502638
47
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
CONFIGURING THE REMOTE
CONFIGURING THE REMOTE 47
that does not operate properly by using the learning
technique shown on this page.
Automatic Code Entry
In addition to manual code selection using the brand
name list, it is also possible to automatically search
through all the codes that are stored in the AVR remote’s
library to see whether a device will respond even if it
is not listed among the brands that appear when you
program the remote manually. To automatically search
through the codes that are available for a specific device
type (e.g., DVD, VCR), follow these steps:
1. Turn on the power to the device you wish to
program into the AVR remote. This is important
because in a later step you will need to see whether
the device turns off to determine whether the remote
has been programmed for the proper remote codes.
2. Press and hold the Program Button y for
about three seconds while the message shown
in Figure 21 appears in the remote’s LCD
Information Display c. Release the button
when the red light under the Set Button q
appears.
3. The remote’s MAIN MENU message (Figure
22) will appear in the LCD display and the Set
Button q will remain illuminated in red. Press
the Set Button q to begin the process of
selecting a device and locating the proper
remote codes.
4. SELECT A DEVICE will appear in the LCD
display (Figure 23). Press the
/
¤
Navigation
Button o to scroll through the list of device
categories and press the Set Button q when
the device for which you wish to set the codes
appears. For this example, we will select “TV” to
enter the codes needed to operate your TV.
5. At the next menu screen on the remote, press the
Navigation Button o so that the bottom line
of the LCD display reads AUTO (Figure 28) and
then press the Set Button q to enter the
Automatic programming mode.
Figure 28
6. As instructed on the next menu screen, press
the
Navigation Button o to begin the
automatic code search process. Your confirmation
that the remote is sending out commands is the
movement of a square block across the top line
of the LCD display screen while the bottom line
reads PLEASE WAIT. You will also see the
transmit icon in the upper right corner of the LCD
display’s top line to remind you that the remote is
working even though you may not see anything
happening to the device being programmed.
7. It will take a few seconds for the remote to send
out the first group of commands, after which you
will see a new display in the LCD screen, as
shown in Figure 29. Following the instructions, if
the device being programmed has
not
turned off,
press the
Navigation Button o again to
send another group of codes. If the device being
programmed
has
turned off, skip to Step 9.
Figure 29
8. By pressing the
Navigation Button o
again, the remote will send out a new set of
commands. When it pauses, follow the instructions
shown in Step 7. Depending on how many codes
are stored for a specific device type, you may
have to repeat this process as many as fifteen
times. Remember, if the device turns off, skip to
Step 9. When all the codes for the device being
programmed have been tried, the instruction
shown in Figure 30 will appear. This means that
the codes for the product you are trying to pro-
gram are not in the AVR remote library and you
will have to “learn” them into the remote following
the instructions shown in the next section. Press
the Set Button q as instructed to exit the
programming process.
Figure 30
9. If the device being programmed
does
turn off
after following the instructions in Step 7, you
will need to verify the code set by pressing the
Numeric Keys k in sequence, as instructed in
Figure 26. Point the remote at the device being
programmed, and press the “1” Button k to
see whether the device turns back on.
10. After pressing and releasing the “1” Button k,
check to see whether the device has turned back
on. If it has, skip to Step 12. If it does not turn off,
press the “2” Button k, or the next button in
the numeric sequence if you are repeating the
procedure, as instructed by the LCD screen in
Figure 31.
Figure 31
11. When pressing the “1” button does not turn
the device being programmed back on, repeat
the procedure by trying the remainder of the
Numeric Keys k in sequence, each time
pressing and then releasing the button to see
whether the new device turns back on. When it
does, skip to the next step. However, if you try all
10 numeric keys and find that the unit will not turn
on, you won’t be able to use this method to pro-
gram the device. Press the Clear Button j to
exit the programming process. You’ll need to follow
the Learning Commands instructions below to enter
the codes for this device into the AVR remote.
12. When pressing one of the numeric keys in Step
10 or 11 causes the device being programmed
to turn back on, follow the instructions shown in
Figure 29 and press the Set Button q within
five seconds of the device turning on. After you
press the Set button, the top line of the LCD dis-
play will read SAVING… and then the word
SAVED will flash four times in the center of the
bottom line.
13. When the codes are saved, the remote will return
to normal operation, and whenever you press
the Input Selector Button d that was just
programmed, the codes for the new device will
be used.
Learning Commands
On occasions when the AVR remote does not contain
the codes for a particular product’s remote in its built-
in library, or when you wish to program a missing or
special function into one button of a device, the AVR
remote’s learning capability allows you to do that. To
teach commands from one product’s remote into the
AVR remote, follow the steps below:
The process requires that both the device’s original
remote and the AVR remote be available. Before
pressing any buttons on either remote, place them so
that the IR transmitter on the remote from the device
to be programmed is facing the Infrared Lens
l
on the AVR remote. The two remotes should be no
more than an inch apart, and there should not be any
direct sunlight or other bright light source near the
remotes.
1. Press and hold the Program Button y for
about three seconds while the message shown
in Figure 21 appears in the remote’s LCD
Information Display c. Release the button
when the red light under the Set Button q
appears.
2. The remote’s MAIN MENU message (Figure
22), will appear in the LCD display and the Set
Button q will remain illuminated in red. Press
the
Navigation Button o once so that
LEARN appears on the bottom line of the LCD
screen, as shown in Figure 32. Press the Set
Button q to begin the process of learning
POWER ON?
Y - > SET N-> 1 ~ 0
REACH END POINT
EXIT -> SET KEY
POWER OFF?
Y - > 1~ 0 N->
PROGRAM DEVICE
AUTO
AVR7300(120v)-OM 6/14/04 9:15 AM Page 47
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR7300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR7300 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info