Handleiding Harman Kardon AVR7200 (pagina 20 van 52) (Engels)

502637

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

SYSTEM CONFIGURATION

20 SYSTEM CONFIGURATION20 SYSTEM CONFIGURATION

the MASTER MENU (Figure 1) appears. The

›

cursor will be next to the IN/OUT SETUP line.

Press the Set Button p to enter the menu and the

IN/OUT SETUP menu (Figure 2) will appear

on the screen. Press the

‹

›

Navigation Button

n until the desired input name appears in the high-

lighted video, as well as being indicated in the front-

panel Input Indicators ˆ by the green LED next to

the desired input name. If the input will use the stan-

dard left/right analog inputs, no further adjustment is

needed.

Figure 2

If you wish to associate one of the digital inputs with

the selected input source, press the

Navigation

Button n on the remote while the IN/OUT

SETUP menu (Figure 2) is on the screen, and the

on-screen cursor will drop down to the DIGITAL

IN line. Press the

‹

›

Navigation Button n until

the name of the desired digital input appears. To return

to the analog input, press the button until the word

ANALOG appears. When the correct input source

appears, press the

Navigation Button n

once so that the

›

cursor appears next to BACK

TO MASTER MENU, and press the Set

Button p.

To change the digital input at any time using the dis-

crete function buttons and the semi-OSD system,

press the Digital Select Button o on the remote.

Within five seconds, make your input selection using

the

⁄

Navigation Button n until the desired

digital or analog input is shown in the Upper Display

Line A and in the lower line of the on-screen dis-

play. Press the Set Button p to enter the new digi-

tal input assignment.

NOTE: When a source such as an HDTV receiver

or a digital cable set-top box is used, you may wish

to connect both the coaxial digital output and the

standard, analog output of the source to the AVR’s

VID 2 and Coax 2 inputs since the program sources

and channels received by these devices often switch

between analog and digital audio. To simplify opera-

tion, the AVR 7200 will automatically select whichever

output is active and change the AVR’s input setting.

An exclusive Harman Kardon feature is the ability to

switch the front-panel coaxial digital audio and analog

audio/video jacks from their normal use as inputs to

output connections so that portable recording devices

may easily be connected. On the AVR 7200, the

Digital Coax 3 Jack ( is normally an input, but

this may also be switched to a digital output for use

with CD-R/RW decks, MD recorders or other A/V

recorders. To change the jack to an output, press

the

⁄

Navigation Button n while the

IN/OUT SETUP menu is on the screen until

the

›

cursor is next to COAXIAL 3. Then press

the

‹

›

Navigation Button n so that the word

OUT is highlighted. The Input/Output Status

Indicator * will turn red, indicating that the jack is

now a record output.

NOTE: A signal will be sent to this jack only when the

input selected for use by the AVR 7200 is digital.

Digital signals will be passed through regardless of

their format, and which digital input (optical or coax)

they are fed from. However, analog signals are not

converted to digital, and the format of the signal (e.g.,

PCM, Dolby Digital or DTS) may not be changed.

The front-panel analog

Video 4 Inputs Ó are nor-

mally set as an input for use with camcorders, video

games and other portable audio/video products, but

they may be switched to an output for connection to

portable audio/video recorders. To temporarily switch

them to outputs, you must first be at the

IN/OUT

SETUP menu. Press the

Navigation Button

n until the on-screen

›

cursor is pointing to the

VIDEO 4 line. Press the

›

Navigation Button

n so that the word OUT is highlighted. The

Input/Output Status Indicator * between the S-

and composite video jacks will turn red, indicating that

the analog Video 4 jacks are now record outputs.

Selection of the front-panel jacks as an output will

remain effective as long as the AVR 7200 is on. Once

the unit is turned off, the jacks will revert to their nor-

mal use as an input when the unit is turned on again.

When all needed adjustments have been made, press

the

Navigation Button n until the

›

cursor is

next to BACK TO MASTER MENU to con-

tinue with the system configuration.

Surround Setup

he next step is to set the surround mode you wish

to use with the input that was previously selected in

the

IN/OUT menu. Since surround modes are a

matter of personal taste, feel free to select any mode

you wish – you may change it later. However, to make

it easier to establish the initial parameters for the

AVR 7200, it is best to select Dolby Pro Logic II or

Logic 7 for most analog inputs and Dolby Digital for

inputs connected to digital sources. In the case of

inputs such as a CD player, tape deck or tuner, you

may wish to set the mode to Stereo (“Surround off”)

as they are not typically used with multichannel

program material, and it is unlikely that sur

round-

encoded material will be used. Alternatively, the

Logic 7

Music mode is a good choice for stereo-only source

material. See page 29 for more information on avail-

able surround modes.

When selecting surround modes for digital program

material, the AVR 7200 will always examine the data

stream and automatically select Dolby Digital or DTS

as applicable.

It is easiest to complete the surround setup using the

full-OSD on-screen menus. From the

MASTER

MENU (Figure 1), press the

⁄

Navigation

Button n until the

›

cursor is next to the SUR-

ROUND SELECT menu. Press the Set Button

p until the SURROUND SELECT menu

(Figure 3) is on the screen.

Figure 3

Each of the option lines on this menu (Figure 3)

selects the surround mode group, and within each of

those groups there will be a choice of the specific

mode options. The choice of modes will vary accord-

ing to the speaker configuration in your system. When

the

SURR BACK line of the SPEAKER

SETUP menu (Figure 5) is set to NONE the

AVR 7200 will be configured for 5.1-channel opera-

tion, and only the modes appropriate to a five-speaker

system will appear. When the

SURR BACK line

of the SPEAKER SETUP menu (Figure 5) is

set to SMALL or LARGE the AVR 7200 will

be configured for 6.1/7.1-channel operation, and

additional

modes such as Dolby Digital EX

and DTS-ES

will appear, as they are only available when seven

main speakers are present. In addition, some of the

modes available in the AVR 7200 will not appear

unless a digital source is selected and is playing the

correct bitstream.

To select the mode that will be used as the initial

default for an input, first press the

⁄

Navigation

Button n until the on-screen cursor is next to the

desired mode’s master group name, such as

** SURROUND SELECT **

DOLBY

DTS

LOGIC 7

DSP (SURR)

VMAx

STEREO

BACK TO MASTER MENU

* IN/OUT SETUP *

INPUT :VIDEO 1

DIGITAL IN :OPTICAL 1

COAXIAL 3 :IN OUT

VIDEO 4 :IN OUT

BACK TO MASTER MENU

AVR 7200 OM 1/27/03 4:46 PM Page 20

Harman Kardon AVR7200 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info