502621
6
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
6 S
peaker Selector:
P
ress this button to begin
the process of configuring the unit to match the type
of speakers used in your listening room. (See pages
28–30 for more information on speaker setup and
c
onfiguration.)
7 Surround Mode Group Selector: Press this but-
ton to select the top-level group of surround modes.
E
ach press of the button will select the current or last
used mode in each of the surround mode groups
(e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo).
When the button is pressed so that the name of the
s
urround mode group appears in the on-screen dis-
play and in the
Lower Display Line ı, press the
Surround Mode Selector 8 to cycle through the
individual modes available. For example, press this
button to select Dolby modes, and then press the
Surround Mode Selector 8 to choose from the
various Dolby mode options.
8 Surround Mode Selector: Press this button
to select from among the available surround mode
options for the mode group selected. The specific
modes will vary based on the number of speakers
available, the mode group and if the input source is
digital or analog. For example, press the
Surround
Mode Group Selector
7 to select a main mode
grouping such as Dolby or Logic 7, and then press
this button to see the specific mode choices available.
Note that the digital surround modes, such as Dolby
Digital and DTS, may not be accessed unless that type
of source signal is present, such as when a DVD movie
or television signal programmed in Dolby Digital or DTS
surround sound is playing. For more information on sur-
round mode selection,
see pages 25 and 35–41.
9 Tuning Selector: Press the left side of the button
to tune lower-frequency stations and the right side of
the button to tune higher-frequency stations. When the
tuner is in the Manual mode,
each tap will increase or
decrease the frequency by one increment.
When the
tuner receives a strong enough signal for adequate
reception,
MANUAL TUNED will appear in the
on-screen display and the
Lower Display Line ı.
When the tuner is the Auto mode, press the button
once, and the tuner will scan for a station with accept-
able signal strength.
When the next station with a
strong signal is tuned the scan will stop and the
on-screen display and
Lo
wer Display Line
ı
will indicate AUTO
TUNED
.
When an FM
Stereo station is tuned, the display will read
AUTO ST TUNED.
To switch back and forth between the Auto and
Manual tuning modes, press the
Tuner Mode
Selector
&.
) / B
uttons:
W
hen configuring the AVR 340’s
settings, use these buttons to select from all of the
available choices
.
! Tuner Band Selector: Press this button to turn
the AVR on and to select the Tuner as the input. Press
it again to switch between the AM and FM frequency
bands. (See page 41 for more information on the tuner.)
@ Set Button: When making choices during the
setup and configuration process, press this button
t
o enter the desired setting into the AVR 340’s memory.
# Digital Input Selector: Press this button to
select one of the digital audio inputs or the analog
audio input for any source. (See pages 38–41 for
more information on digital audio.)
$ Preset Stations Selector: Press this button to
scroll up or down through the list of stations that have
been entered into the preset memory. (See page 41
for more information on tuner presets.)
% Delay
Adjust Selector:
Press this button to
begin the steps required to enter delay settings. (See
pages 30–31 for more information on delay times.)
^ Input Source Selector: Press this button to
change the input by scrolling up or down through the
list of
Input Indicators Ú.
& Tuner Mode Selector: Press this button to select
Auto or Manual tuning. When the button is pressed so
that the
AUTO appears in the Lower Display Line
ı, the tuner will search for the next station with an
acceptable signal when the
Tuning Selector 9u
˚
is pressed.
When the button is pressed so that
MANUAL appears in the Lo
wer Display Line
ı,
each press of the
Tuning Selector 9u
˚
will
increase the frequency. This button may also be used to
switch between Stereo and Mono modes for FM radio
reception. When weak reception is encountered,
press
the button so that
MANUAL appears in the Lo
wer
Display Line
ı and on the on-screen display to
switch to Mono reception. Press it again to switch back
to Stereo mode
.
(See page 41 for more infor
mation on
using the tuner.)
* Optical 4 Digital Audio Input: Connect the optical
digital audio output of an audio or video product to this
jack. When the input is not in use, the built-in shutter will
close to avoid dust contamination that might degrade
future perfor
mance.
( Coaxial 4 Digital Audio Input: This jack is used
for connection to the output of portable audio devices,
video game consoles or other products that have a
coax digital audio jack.
Ó V
ideo 4 Video Input Jacks:
T
hese jacks may
be used for temporary connection to the composite or
S-video output of video games, camcorders or other
portable video products. You may make a connection
t
o either jack at any time, but not to both simultaneously.
Ô Video 4 Audio Input Jacks: These audio jacks
may be used for temporary connection to video
g
ames or portable audio/video products such as
camcorders and portable audio players.
NOTE: The AVR 340 is shipped with two covers that
may be installed over the front-panel input jacks when
they are not in use.
Channel Adjust Selector: Press this button to
begin the process of trimming the channel output lev-
els using an external audio source. (For more informa-
tion on output level trim adjustment,
see page 31.)
Ò Volume Control: Turn this knob clockwise to
increase the volume, counterclockwise to decrease
the volume. If the AVR 340 is muted, adjusting the
Volume Control Òb
©
will automatically
release the unit from the silenced condition.
Ú Input Indicators: The current selected source
will appear as one of these indicators. When the unit
is turned on, the entire list of available modes will
light briefly, and then revert to normal operation with
only the active mode indicator illuminated.
NOTE: When /DMP has been selected as
the input source, no
Input Indicator N will light.
DMP/THE BRIDGE IS CONNECTED
will scroll across the Upper Display Line P, unless
you have retitled the source name, in which case that
name will appear. See page 22 for more information
on input titling.
Û Speaker/Channel Input Indicators: These indi-
cators are multipurpose, indicating both the speaker
type selected for each channel and the incoming data-
signal configuration. The left, center, right, side surround
and back surround speaker indicators are composed of
three boxes, while the subwoofer is a single box. The
center box lights when a “small” speaker is selected,
and the two outer boxes light when
“large” speakers are
selected. When none of the boxes are lit for the center,
surround or subwoofer channels, no speaker has been
assigned that position. (See pages 28–29 for more
infor
mation on configuring speakers.)
NOTE: When you have reassigned the surround back
speakers to the remote zone using the
MULTI
ROOM SETUP
menu, the boxes that indicate the
presence of the surround back speakers will automati
-
cally disappear, reflecting the fact that the main listen-
ing area is now configured for 5.1-channel operation.
The
Bridge
T
M
FRONT-PANEL CONTROLS
6 FRONT-PANEL CONTROLS
FRONT-PANEL CONTROLS
AVR 340 OM 3/22/06 9:09 AM Page 6
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR340 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR340 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Harman Kardon AVR340

Harman Kardon AVR340 Snelstart handleiding - English - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info