Handleiding Harman Kardon AVR 4000 (pagina 39 van 58) (Engels)

8518

Verklein

Vergroot

Pagina terug

1/58

Pagina verder

PROGRAMMING THE REMOTE 39

Programming the Remote

The AVR 4000 is equipped with a powerful

remote control that will control not only the

receiver’s functions, but also most popular brands

of audio and video equipment, including CD

players, TV sets, cable boxes, VCRs, satellite

receivers and other home-theater equipment.

Once the AVR 4000’s remote is programmed

with the codes for the products you own, it is

possible to eliminate most other remotes and

replace them with the convenience of a single

universal remote control.

Programming the Remote

with Codes

As shipped from the factory, the remote is fully

programmed for all AVR 4000 functions, as well as

those of most Harman Kardon CD changers, DVD

players, CD players and cassette decks. In addition,

by following one of the methods below, you may

program the remote to operate a wide range of

devices from other manufacturers.

Note: The Input Selector button Video 4

cannot be programmed with codes as it functions

as input selector for the AVR only. Moreover, only

the default code "001" can be programmed on

the AVR Selector button

Direct Code Entry

This method is the easiest way to program your

remote to work with different products.

1. Use the tables in the following pages to deter-

mine the three-digit code or codes that match

both the product type (e.g., VCR,TV), and the

specific brand name. If there is more than one

number for a brand, make note of the different

choices.

2. Turn on the unit you wish to program into the

AVR 4000 remote.

3. Press and hold both the Input Selector

for the type of product to be entered (e.g., VCR,

TV) and the Mute button

at the same

time. When the Program/SPL Indicator

turns amber and begins flashing, release the but-

tons. It is important that you begin the next step

within 20 seconds.

4. If the unit you wish to program into the AVR

4000 remote has a remotable Power on/off func-

tion, follow these steps:

a. Point the AVR 4000’s remote towards the unit

to be programmed, and enter the first three-

digit code number using the Numeric buttons

. If the unit being programmed turns off, the

correct code has been entered. Press the Input

Selector

again, and note that the red

light under the Input Selector will flash three

times before going dark to confirm the entry.

b. If the product to be programmed does NOT

turn off, continue to enter the three-digit code

numbers until the equipment turns off.At this

point, the correct code has been entered. Press

the Input Selector

again and note that

the red light under the Input Selector will

flash three times before going dark to confirm

the entry.

5. If the Power function of the unit to be pro-

grammed cannot be remoted, follow these steps

(max. 20 seconds after step 3 above, or else step

3 must be repeated first):

a. Enter the first three-digit code number using

the Numeric buttons

and press the

Input Selector

again. Press the remote

button of any transport function remotable

with the unit, e.g. Pause or Play

ﬂ

.If

the unit being programmed starts that func-

tion, the correct code has been entered.

b. If the unit does not start the function whose

button was pressed, repeat steps 3 and 5a

above with the next three-digit code number

listed in the setup code table for that brand

and product type, until the unit reacts properly

on the transport function transmitted.

6. Try all of the functions on the remote to make

certain that the product operates properly. Keep

in mind that many manufacturers use a number

of different combinations of codes, so it is a good

idea to make certain that not only does the

Power control work, but that the volume, channel

and transport controls work as they should. If

functions do not work properly, you may need to

use a different remote code.

7. If the unit does not react to any code en-

tered, if the code for your product does not

appear in the tables in this manual, or if not all

functions operate properly, try programming the

remote with the Auto Search Method.

Note on Using the AVR 4000 remote with

a Harman Kardon CD Recorder.

As shipped from the factory the remote is pro-

grammed for controlling Harman Kardon CD

players. But it is able to control most functions

of the CD Recorder CDR2 and CDR20 (see func-

tion list on page 44) too after the code ”002” is

entered to the CD Selector button

described above. For returning to the CD player

control commands the code ”001” must be

entered.

Auto-Search Method

If the unit you wish to include in the AVR 4000’s

remote is not listed in the code tables in this

manual or if the code does not seem to operate

properly, you may wish to program the correct

code using the Auto Search method that follows.

Note that the Auto Search method works only

with units whose Power functions can be

remoted:

1. Turn on the product that you wish to include in

the AVR 4000 remote.

2. Press and hold both the Input Selector

for the type of product to be entered (e.g., VCR,

TV) and the Mute button

at the same

time. When the Program/SPL Indicator

turns amber and begins flashing, release the but-

tons. It is important that you begin the next step

within 20 seconds.

3. To find out if the code for your unit is pre-pro-

grammed, point the AVR 4000 remote towards

the unit to be programmed, and press and hold

the

⁄

button

.This will send out a series of

codes from the remote’s built-in data base, with

each flash of the red light under the Input

Selector

indicating that a code has been

sent.When the device to be programmed turns

off,immediately release the

⁄

button

. Note

that it may take one minute or more until the

right code is found and the unit turns off.

4. When the

⁄

button was not released in time

after the unit turned off, the proper code will be

”overrun”. That’s why a function test should be

made: Turn the unit on again and, while the

Input Selector

still lights red, press the

⁄

button

once, than the

button

once

too. When the unit turns off, the right code was

found, when not, the code was ”overrun”.To re-

find the correct, while the Input Selector

still lights red, press (not hold pressed) the

button

repeatedly to step backwards

through the codes available and observe the

reaction of the unit at each press. As soon as the

unit turns off the correct code is found.

5. Press the Input Selector

again, and

note that the red light will flash three times

before going dark to confirm the entry.

6. Try all of the functions on the remote to make

certain that the product operates. Keep in mind

that many manufacturers use a number of differ-

ent combinations of codes, and it is a good idea

to make certain that not only the Power control

works, but the volume, channel and transport

controls, as appropriate. If all functions do not

work properly, you may need to Auto-Search for

a different code, or enter a code via the Direct

Code Entry method.

Code Readout

When the code has been entered using the Auto

Search method, it is always a good idea to find

out the exact code so that it may be easily

reentered if necessary. You may also read the

codes to verify which device has been

programmed to a specific Control Selector

button.

Harman Kardon AVR 4000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Harman Kardon AVR 4000

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info