Handleiding Harman Kardon AVR 4000 (pagina 21 van 58) (Engels)

8518

Verklein

Vergroot

Pagina terug

1/58

Pagina verder

SYSTEM CONFIGURATION 21

Input Setup

The first step in configuring the AVR 4000 is to

select an input. This may be done by pressing

the front panel Input Source Selector

until the desired input’s name appears momen-

tarily in the Main Information Display

and the green LED lights next to the input’s

name in the front panel Input Indicators



The input may also be selected by pressing the

appropriate Input Selector on the remote control

When using the full-OSD system to make the

setup adjustments, press the OSD button

once so that the MASTER MENU (Figure

1) appears. Note that the

› cursor will be next

to the IN/OUT SETUP line. Press the

Set button

to enter the menu and the

IN/OUT SETUP menu (Figure 2) will

appear on the screen. Press the

‹/› buttons

until the desired input name appears in

the highlighted video, as well as being indicated

in the front panel Input Indicators



by the

green LED next to the desired input name. If the

input will use the standard left/right analog

inputs, no further adjustment is needed.

Figure 2

If you wish to associate one of the digital inputs

with the selected input source, press the

¤ but-

ton

on the remote while the IN/OUT

SETUP menu (Figure 2) is on the screen, and

note that the on-screen cursor will drop down to

the DIGITAL IN line. Press the

‹/› but-

tons

until the name of the desired digi-

tal input name appears. To return to the

ANALOG input, press the buttons until the

word analog appears. When the correct input

appears, press the

¤ button

until the ›

cursor appears next to RETURN TO

MENU, and press the Set button

To change the digital input associated with the

input selected at any time using the discrete

function buttons and the semi-OSD system,

press the Digital Input Select button

on the front panel or the remote. Within five sec-

onds, make your input selection using the

Selector buttons on the front panel

or the

⁄/¤ buttons

on the remote until the

desired digital or analog input is shown in the

Main Information Display

and in the

lower third of the video display connected to the

AVR 4000. Then press the Set button

enter the new digital input assignment.

An exclusive Harman Kardon feature is the abili-

ty to switch front panel jacks from their normal

use as inputs to output connections so that

portable recording devices may easily be con-

nected. On the AVR 4000, the Coaxial 3

Digital Jack

is normally an input, but it

may also be switched to a digital output for use

with CD-R/RW decks, MD recorders or other dig-

ital audio recorders. To change the jack to an

output, press the

⁄/¤ buttons

while the

IN/OUT SETUP menu is on the screen

so that the

› cursor is next to COAXIAL

3. Then press the

‹/› buttons

so that

the word OUTis highlighted. Note that the

Digital Coax 3 Status Indicator

will turn

red, indicating that the jack is now a record out-

put.

Note: A signal will be sent to this jack only

when the input selected for use by the AVR

4000 is digital. Digital signals will be passed

through regardless of their format, and which

digital input (optical or coax) they are fed from.

However, analog signals are not converted to

digital, and the format of the signal (e.g., PCM,

Dolby Digital or DTS) may not be changed.

Selection of the Digital Coax 3 jack as an

output will remain effective as long as the

AVR 4000 is on. However, once the unit is

turned off, the jack will revert to its normal use

as an input when the unit is turned on again.

Surround Setup

Once the input setup has been completed, the

next step for that input is to set the surround

mode you wish to use with that input. Since sur-

round modes are a matter of personal taste, feel

free to select any mode you wish – you may

change it later.The Surround Mode chart on

page 28 may help you select the mode best suit-

ed to the input source selected. However, to

make it easier to establish the initial parameters

for the AVR 4000, it is best to select Dolby Pro

Logic for most analog inputs and Dolby Digital

for inputs connected to digital sources. In the

case of inputs such as a CD Player,Tape Deck or

Tuner, you may wish to set the mode to Stereo, if

that is your preferred listening mode for stan-

dard stereo sources, where it is unlikely that sur-

round encoded material will be used.

Alternatively, the 5 Channel Stereo or

Logic 7

Music mode may also be a good choice for

stereo-only source material.

It is easiest to complete the surround setup

using the full-OSD on-screen menus. From the

main MASTER MENU menu (Figure 1),

press the

⁄/¤ button

until the › cursor is

next to the SURROUND SETUP menu.

Press the Set button

so that the

SURROUND SETUP menu (Figure 3 or 4)

is on the screen.

Figure 3

Figure 4

Since the factory default for all inputs is Stereo,

the words SURR OFFwill initially appear in

highlighted video (Figure 3) unless another sur-

round mode choice was made with the input

just selected. To change the surround mode

while the

› cursor is next to the surround line,

press the

‹/› buttons

until the desired

surround mode’s name appears in the highlight-

ed video. As the modes are changed, a green

LED will also light next to the mode names in

the Surround Mode Indicators

on the

front panel.

Note that the data lines next to the items in the

screen display will show either numbers or a

series of dashes, depending on whether or not

the specific parameter is adjustable. For exam-

ple, the Center Delay and Night Mode items are

only adjustable for Dolby Digital, and the Delay

Time is only adjusted for Dolby Digital and Dolby

Pro Logic. Note, also, that Dolby Digital and DTS

will only appear as choices (Figure 4) when a

digital input was previously selected.These set-

tings for Delay, Crossover Frequency and Night

mode, that are independent of any input select-

ed, will be described in the next chapter on page

23.

Speaker Setup

This menu tells the AVR 4000 which type of

speakers are in use.This is important as it

adjusts the settings that determine which

speakers receive low frequency (bass) informa-

tion. For each of these settings use the

LARGE setting if the speakers for a

particular position are traditional full-range

loudspeakers that are capable of reproducing

sounds below 100Hz. Use the SMALL set-

ting for smaller, frequency-limited satellite

speakers that do not reproduce sounds below

100Hz. Note that when “small” front (left and

right) speakers are used, a subwoofer is

required to reproduce low frequency sounds. If

* SURROUND SETUP *

SURROUND: DOLBY

DIGITAL

CENTER DELAY: 0MS

SURR DELAY: 00MS

NIGHT: OFF MID MAX

RETURN TO MENU

* SURROUND SETUP *

SURROUND: SURR OFF

CENTER DELAY: MS

SURR DELAY: MS

NIGHT:   

RETURN TO MENU

* IN/OUT SETUP *

INPUT :VIDEO 1

DIGITAL IN:ANALOG

COAXIAL 3 :IN OUT

RETURN TO MENU

System Configuration

Harman Kardon AVR 4000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Harman Kardon AVR 4000

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info