534556
32
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
32
AVR
Advanced Functions
For each speaker group, select one of these eight crossover frequencies: Large, 40Hz,
50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz, 110Hz, 120Hz, 140Hz, 150Hz, 160Hz, 180Hz
or 200Hz. If the speaker’s crossover frequency is below 40Hz, select the first option,
“Large.” This setting doesn’t refer to the speaker’s physical size but to its frequency
response, which is also called “full range.”
NOTE: If you have Room EQ set to On, the crossover frequencies have been automatically
set by the AVR and cannot be adjusted.
Write down the settings in Table A6 in the Appendix.
When you have finished entering the settings, press the Back/Exit button to return to the
Manual Setup menu.
Select the “Speakers” menu again and note the Subwoofer setting: This setting depends
upon the Crossover setting you selected for the front left and right speakers.
If you set the front speakers to a numeric crossover frequency, the subwoofer •
setting will always be SUB. All low-frequency information will always be sent to the
subwoofer. If you don’t have a subwoofer, either upgrade to full-range front left and
right speakers or add a subwoofer at the earliest opportunity.
If you set the front left/right speakers to LARGE, select one of the three following •
settings for the subwoofer:
L/R+LFE: This setting sends all low-frequency information to the subwoofer,
including a) information that would normally be played through the front left and
right speakers and b) the special low-frequency effects (LFE) channel information.
OFF: Select this setting when no subwoofer is in use. All low-frequency information
will be sent to the front left and right speakers.
LFE: This setting plays low-frequency information contained in the left and right
program channels through the front left and right speakers, and directs only the
LFE-channel information to the subwoofer.
Distance
As described above in Step Two, when you measured the distances from each of your
speakers to the listening position, your AVR provides an adjustment that compensates
for the different distances so that the sound from each speaker will reach the listening
position at the proper time. This process will improve the clarity and detail of the sound.
On the Manual Setup menu, move the cursor to the Distance line and press the OK button
to display the Adjust Speaker Distance menu.
Enter the distance from each speaker to the listening position that you measured in Step
Two and recorded in Table A4 in the Appendix (see page 39). Select a speaker, then use
the Left/Right buttons to change the measurement. You can enter distances between 0
and 30 feet (9.1m). The default distance for all speakers is 10 feet (3m).
The default unit of measurement is feet. To change the unit to meters, select the Unit of
Measure line and press the Left or Right button to change the setting.
NOTE: If you set the Assigned AMP channels to Zone 2, you will not be able to adjust
their delay settings.
Step Four – Setting Channel Output Levels Manually
For a conventional stereo receiver, a simple balance control adjusts the stereo imaging
by varying the relative loudness of the left and right channels. In a home theater system
with up to seven main channels plus up to two subwoofers, achieving proper imaging
becomes both more critical and more complex. The goal is to ensure that each channel
is heard at the listening position with equal loudness (when signals of equal loudness
are played through them).
Your AVR’s EzSet/EQ calibration can handle this critical task for you simply and
automatically. However, the Output Adjust menu allows you to calibrate the levels
manually, either using the system’s built-in test tone or while playing source material.
From the Manual Setup menu select Output Adjust to display the speaker volume
adjustment menu.
All of the system’s speakers will appear with their current level settings. You can adjust
each speaker’s level between –10dB and +10dB in 1dB increments.
While making adjustments, you can measure the channel levels in one of these ways:
Preferably, use a handheld SPL meter set to the C-weighting, slow scale. Adjust each •
speaker so that the meter reads 75dB when the AVR’s built-in test noise is playing.
By ear. Adjust the levels so that the test tone sounds equally loud to you when it plays •
through each speaker.
To set your levels using the AVR’s internal test tone, select the menu’s Test Tone line and
use the Left/Right buttons to turn the test tone on. Then select the Test Tone SEQ line to
select between Auto and Manual:
Auto: The test tone will automatically circulate to all speakers, as indicated by the
highlight bar. Use the Left/Right buttons to adjust the level for any speaker when the test
tone is paused there. Use the Up/Down buttons to move the highlight bar to another line,
and the test tone will follow the bar. To stop the test tone, use the Up/Down buttons to
move the cursor out of the screen’s speaker listings area.
Manual: The test tone will stay on the selected speaker until you use the Up/Down
buttons to move it to another speaker. Use the Left/Right buttons to adjust the level for
the speaker through which the test tone is playing.
If you are using an external source to set your output levels, set Test Tone to Off, use the
Up/Down buttons to navigate to each speaker, and use the Left/Right buttons to adjust
the speaker’s level while the source plays.
NOTE: If you are using a handheld SPL meter with external source material, such as a
test disc or an audio selection, play it and adjust the AVR’s master volume control until
the meter measures 75dB. Then adjust the individual speaker levels.
Output Reset: To reset all levels to their factory defaults of 0dB, scroll down to this line
and press the OK button.
When you have finished adjusting the speaker levels, record the settings in Table A3 in
the Appendix. Then press the Back/Exit Button.
32

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Harman-Kardon-AVR-161

Zoeken resetten

  • Ik heb glasvezel aansluiting geinstalleerd van kpn. Mijn Harman cardon kan ik nu niet goed installeren. Alles nieuw. Gesteld op 16-7-2023 om 11:15

    Reageer op deze vraag Misbruik melden
  • hoe krijg het geluid van de TV over Harman Cardon A V R 161/230 Gesteld op 3-4-2023 om 10:09

    Reageer op deze vraag Misbruik melden
  • op welke wijze kan ik draadloos muziek ontvangen van laptop Gesteld op 3-3-2021 om 12:39

    Reageer op deze vraag Misbruik melden
  • SUB TS 11 AKTIEVE SUBWOOFER HARTMAN KADON
    TYDENS HET AANDOEN HOOR IK EEN BROMMER GELUID EN ALS OF DIE BOX GAAT DREUNEN Gesteld op 22-11-2017 om 19:35

    Reageer op deze vraag Misbruik melden
    • Hoi ik heb dat probleem ook gehad maar nadat ik het systeem gereset heb was het voorbij. Dat zal niet altijd de oplossing zijn. Probeer als het niet lukt op deze manier eens een nieuwe kabel van avr naar sub, ik heb begrepen dat veel mensen hetzelfde probleem met het brommend al dan niet ploffend geluid hebben mbt de actiefe sub, en dat als het indd aan de sub ligt het een duur grapje kan zijn want dan heb je een probleem met de printplaat bnnenin dat ding. Succes mvg Martijn Moes moes1979@live.nl Geantwoord op 17-10-2018 om 01:14

      Waardeer dit antwoord (2) Misbruik melden
    • Laten op meten en meestal is dat je printplaat
      By deze heb ik het vernieuwd
      Prys 180 euro compleet met plaatsen
      Geluid is weer perfect geluid Geantwoord op 3-1-2019 om 11:51

      Waardeer dit antwoord Misbruik melden
  • Hoe krijg ik mijn Hartman kardon avr 161 230 uit de slaapstand

    Gesteld op 15-9-2017 om 16:21

    Reageer op deze vraag Misbruik melden
  • Ik heb geen tulp aansluiting aan mijn speakers maar losse draad eindes. Zijn tulp aansluiting noodzakelijk? Gesteld op 5-6-2015 om 18:20

    Reageer op deze vraag Misbruik melden
  • 6

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR 161 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR 161 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Harman Kardon AVR 161

Harman Kardon AVR 161 Gebruiksaanwijzing - Nederlands - 52 pagina's

Harman Kardon AVR 161 Gebruiksaanwijzing - Deutsch - 52 pagina's

Harman Kardon AVR 161 Snelstart handleiding - English - 11 pagina's

Harman Kardon AVR 161 Gebruiksaanwijzing - Français - 52 pagina's

Harman Kardon AVR 161 Gebruiksaanwijzing - Italiano - 52 pagina's

Harman Kardon AVR 161 Gebruiksaanwijzing - Espanõl - 52 pagina's

Harman Kardon AVR 161 Gebruiksaanwijzing - Polski - 52 pagina's

Harman Kardon AVR 161 Gebruiksaanwijzing - Dansk - 52 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info