Handleiding Harman Kardon AVR 1510 (pagina 21 van 47) (Engels)

534559

Verklein

Vergroot

Pagina terug

1/47

Pagina verder

ENGLISH

AVR

Speakers

This selection lets you program the correct setting for each speaker group. The settings

in this menu affect the remainder of the speaker setup process and the availability of

various surround modes at any time.

Select ON when the speakers are present in the system; select OFF for positions where

no speakers are installed. The Front Left & Right setting is always ON and may not be

disabled.

When you have ﬁnished, press the Back/Exit button.

Crossover

After you return to the Speaker Setup menu, navigate to the Crossover line and press the

OK button to display the Crossover menu.

The AVR will display only those speaker groups you set to On in the Number of Speakers

menu.

Refer to Table A2 to see the crossover frequencies that you wrote down for your

speakers.

For each speaker group, select one of these eight crossover frequencies: Large, 40Hz,

60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the speaker’s crossover frequency is

below 40Hz, select the ﬁrst option, “Large.” This setting doesn’t refer to the speaker’s

physical size but to its frequency response, which is also called “full range.”

We recommend that you set the Subwoofer Crossover to the same frequency you used

for the Front Left & Right speaker setting. If you set the Front Left & Right speakers

to “Large”, we recommend that you experiment with different Subwoofer Crossover

Frequency settings to ﬁnd the one that produces the best blend between the subwoofer

and Front Left & Right speakers with your system in your room.

Write down the settings in Table A2 in the Appendix.

When you have ﬁnished entering the settings, press the Back/Exit button to return to the

Speaker Setup menu.

Select the “Speakers” menu again and note the Subwoofer setting: This setting depends

upon the Crossover setting you selected for the front left and right speakers.

If you set the front speakers to a numeric crossover frequency, the subwoofer Ř

setting will always be Sub. All low-frequency information will always be sent to the

subwoofer. If you don’t have a subwoofer, either upgrade to full-range front left and

right speakers or add a subwoofer at the earliest opportunity.

If you set the front left/right speakers to Large, select one of the three following Ř

settings for the subwoofer:

L/R+LFE: This setting sends all low-frequency information to the subwoofer,

including a) information that would normally be played through the front left and

right speakers and b) the special low-frequency effects (LFE) channel information.

OFF: Select this setting when no subwoofer is in use. All low-frequency information

will be sent to the front left and right speakers.

LFE: This setting plays low-frequency information contained in the left and right

program channels through the front left and right speakers, and directs only the

LFE-channel information to the subwoofer.

Distance

As described above in Step Two, when you measured the distances from each of your

speakers to the listening position, your AVR provides an adjustment that compensates

for the different distances so that the sound from each speaker will reach the listening

position at the proper time. This process will improve the clarity and detail of the sound.

On the Speaker Setup menu, move the cursor to the Distance line and press the OK

button to display the Adjust Speaker Distance menu.

Enter the distance from each speaker to the listening position that you measured in Step

Two and recorded in Table A3 in the Appendix (see page 33). Select a speaker, then use

the Left/Right buttons to change the measurement. You can enter distances between 0

and 30 feet (9.1m). The default distance for all speakers is 10 feet (3m).

The default unit of measurement is feet. To change the unit to meters, select the Unit line

and press the Left or Right button to change the setting.

Step Four – Setting Channel Output Levels

For a conventional stereo receiver, a simple balance control adjusts the stereo imaging

by varying the relative loudness of the left and right channels. In a home theater system

with up to ﬁve main channels plus a subwoofer, achieving proper imaging becomes

both more critical and more complex. The goal is to ensure that each channel is heard

at the listening position with equal loudness (when signals of equal loudness are played

through them).

The Output Adjust menu allows you to calibrate the levels manually, either using the

system’s built-in test tone or while playing source material.

From the Speaker Setup menu select Output Adjust to display the speaker volume

adjustment menu.

All of the system’s speakers will appear with their current level settings. You can adjust

each speaker’s level between –10dB and +10dB in 1dB increments.

Set Up the AVR

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Harman Kardon AVR 1510 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Harman Kardon AVR 1510

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info