Handleiding Hako Scrubmaster B140R (pagina 31 van 38) (Engels)

683782

Verklein

Vergroot

Pagina terug

1/38

Pagina verder

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Scrubmaster B140 R is equipped

Hako Scrubmaster B140R Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info