Handleiding Haas-Sohn COMPACT-PELLET 310 (pagina 14 van 40) (Engels)

812036

Verklein

Vergroot

Pagina terug

1/40

Pagina verder

content, different lengths. Precise quality features

can however only be determined with suitable

technical analysis equipment.

A simple quality test: Put a few pellets in a glass

of water:

Good quality: Pellets sink

Poor quality: Pellets float.

The use of poor quality or impermissible fuel

impairs the function of your pellet stove and in

addition can lead to the expiry of the guarantee

and the thereby associated product liability.

Impermissible fuels are e.g. also chippings, straw

or maize. The burning of wood pellets of poor

quality leads to the cleaning intervals becoming

shorter and more fuel being consumed, as a

result however the pellet tank must also be filled

more frequently.

Wood pellets are packed in plastic- or paper

sacks. To ensure trouble-free burning of the wood

pellets it is necessary to transport and store the

fuel as dry as possible and free of dirt. When in

contact with moisture, the pellets swell up greatly.

Take care when filling wood pellets in the storage

container that the pellet sacks do not come into

contact with the hot surfaces of the stove.

Two kilograms of wood pellets have about the

same energy content as one liter of „Heating Oil

Extra Light“. Observed 3-dimensionally, 3 m3 of

wood pellets corresponds to approx. 1,000 liters

of heating oil. Different heating outputs of the

pellet stove are not only caused by the quality of

the pellets, but also by the raw material wood

(type of wood).

7.2. First commissioning of your pellet stove

The materials of the pellet stove must slowly get

used to the development of heat. Through careful

heating you avoid cracks in the furnace plates,

enamel damage and material distortion. Therefore

do not set the target temperature on the control

unit too high (about 1.5°C to 2°C higher than the

momentary room temperature).

• Before the first commissioning, possibly

existing stickers are to be removed as well as

all accessory parts withdrawn from the ash

tray, respectively the furnace, this also applies

to possibly existing transport safety devices.

• Please check, whether the furnace lining is

engaged in its anchoring (this could have

slipped out of its position through transport or

during the installation of the stove).

• Check whether the burner pot is fitting

perfectly in its mounting.

• Close the furnace door.

• Fill the storage container with standardized

pellets (Ø 6 mm).

• Plug in mains cable

• Set the On/Off toggle switch to „1“.

• After the toggle switch is set to ON, the

controller begins with the initialization. This

procedure takes a few seconds.

• After the initialization, the information page

appears – press right key (menu) – set cursor

to operating mode – press right key (select) –

select the required mode of operation with the

cursor – press right key (Save)

• Stove starts with the burner test – duration

approx. 2 minutes – measurement of the

burner soiling.

• After the burner test, the start phase begins.

Tip!!

For the first commissioning, place approx. 30

pellets on the burner. This accelerates the starting

operation.

General:

If the start phase could not be successfully

concluded, i.e. no development of flames or the

required temperature on the temperature sensor

not reached, than a safety shutdown is initiated

and an error message tripped („Start phase

waste-gas target temp. not reached – check

burner – Date and Time“).

Remedying the fault:

After the stove has cooled down, the burner is to

be emptied and if necessary cleaned. Caution!

There may still be glowing cinders in the ash!

Then press the left key on the control unit

continuously until the fault message appears –

then press the right key of the control unit (Ack.)

– the information page now appears – press right

key (menu) – set cursor to operating mode and

press right key (select) – that page appears in

which the operating mode can be selected –

select required operating mode with the cursor

and press right key (Save) – the stove begins

with the burner test (duration approx. 2 minutes)

and then the start phase is initiated.

Note: A possible smell developing due to the

burning-in of the protective enameling disappears

after a short time. Please ventilate the installation

room well. The enameling does not however

contain any toxic vapors.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Haas-Sohn COMPACT-PELLET 310 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Haas-Sohn COMPACT-PELLET 310

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info