514977

HEARTWAY PF7 Handleiding

40
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
1
USERS MANUAL
PT7/PF7
HEARTWAY MEDICAL PRODUCTS CO., LTD.
Part no:70030163-(NHC)
2
CONTENTS
1. Technical Specification…………….................................…………….3
2. Major Assembly… … …………… ……………… …………… … …… ..4
3. Safety Instruction……………………………………………………....5~8
4. Environment Condition………………………… …… … ……………..9
5. Warranty… …………… ………… ……… … ………………… … …… ..10
6. Assembly Instruction…………………………………………………..11~12
7. Adjustment For Seating Comfort……………………………….……..13~15
8. Specification Of Control Panel…..………………………….…………16~32
9. Battery Charger Instruction ……………………………………………33~36
9-1. Appearance…………………………………...............................35
9-2. Specification……………………………………………….……..35
9-3. Charger Instruction………………………………………………..36
9-4. LED indication…………………..……………………………….36
9-5. Troubleshooting…………………………………… …………….36
9-6. Caution…………………………………………………………...36~41
10. Battery Warning…………………………………………………………………42
3
TECHNICAL SPECIFICATIONS
4
MAJOR ASSEMBLY
Your power scooter is shipped partially disassembled for protection during shipping. After
unpacking, please check whether you have received the following main components as our standard
specification (See Fig.1).
1. Scooter (without seat)
2. Captain Seat
1 2
(Fig. 1)
5
SAFETY INSTRUCTION
OPERTATION OF SCOOTER
1. To prevent injury to yourself or others, always ensure that the power is switched off when getting
on or off of the scooter.
2. Always check that the drive wheels are engaged (drive mode) before driving.
(Fig.2)
3. Always check you have selected the correct” forward or reverse” button when about to drive.
(Fig.3)
4. Press the button and allow the driving at LOW speed as shown
S P E E D
on the control Panel
until you are familiar with the scooter. Set the speed control according to your driving ability.
5. Always reduce your speed when making sharp turns.
6. Do not switch off the power when the scooter is still moving forward. This will bring the chair to
an extremely abrupt stop.
7. Use gel/dry batteries only.
Engaged
position
Selected driving
direction.
6
Ramps and Curbs
1. Also check that ramp surface is roughened to prevent slipping. Never drive across a slope or
turn sharply on a slope.
(Fig.4) (Fig.5)
2. When driving up curbs, always check the height of the curb to ensure that it does not exceed
120mm height.
(Fig.6)
Transferring at Free-Wheel Condition
(1) Turn off the power (2) Disengaged the motor
(Fig.7) (Fig.8)
When driving up or down
ramps, be sure to check that
the angle of the slope is less
than 10 degrees (slopes
about 1/6).
Maximum height 120mm
7
(3) The function of the Micro-switch Brake System in the scooter.
(Fig.9)
General
1. Always use a seat belt, and keep your feet on the scooter all the time.
2. Do not over load the scooter with it’s maximum weight capacity of 160kg (352lbs)
3. Do not attempt to lift or move a power scooter by any of its removable parts. Personal injury
and damage to the power chair may result.
4. Never try to use your scooter beyond its limitations as described in this manual.
5. Do not operate your vehicle if it is not functioning properly.
6. Do not connect any electrical or mechanical device to the scooter. Failure to obey this
instruction may result in injury and will void the warranty.
7. Never use electronic radio transmitters such as CB, walkie-talkies, portable computers or
cellular phones while using the vehicle without first turning the scooter off.
Use While Under The Influence Of Medication Or Alcohol
1. Check with your physician if you are taking any medication that may affect your ability to
operate your power scooter safely.
2. Do not operate your scooter while you are under the influence of alcohol, as this may impair
your ability to operate your power scooter in a safe manner.
Electromagnetic interference (EMI) from Radio Wave Sources
The rapid development of electronics, especially in the area of communications, has saturated our
environment with electromagnetic (EM) radio waves that are emitted by television, radio and
communication signals. These EM wave are invisible and their strength increases as one approaches
the source. All electrical conductors act as antennas to the EM signals and, to varying degrees, all
power wheelchairs and scoot-
ers are susceptible to electromagnetic interference(EMI). The interference could result in abnormal,
unintentional movement and/or erratic control of the vehicle. The United States Food and drug
Administration (FDA) suggests that the following statement be incorporated to the user’s manual
When transferring at free-wheel
condition, a brake system will
appear if the transferring speed
is more then 30% of the
scooter’s maximum speed.
8
for all scooters like the PT7 and PF7. Motorized scooters may as susceptible to electromagnetic
interference (EMI), which is interfering electromagnetic energy emitted from sources such as radio
stations, TV stations, amateur radio (HAN) transmitter, two-way radios and cellular phones. The
interference (from radio wave sources) can cause the powered wheelchair to release its brakes,
move by itself or move in unintended directions. It can also permanently damage the powered
scooter’s control system. The intensity of the EM energy can be measured in volts per meter
(V/m).Each powered scooter can resist EMI up to a certain intensity. This is called “immunity
level”. The higher the immunity level, the greater the protection. At this time, current technology is
capable of providing at least 20 V/m of immunity level, which would provide useful protection
against common sources of radiated EMI.
Following the warnings listed below should reduce the chance of unintended brake release or
powered scooter movement that could result in serious injury:
1. Do not turn on hand-held personal communication devices such as citizens band (CB) radios and
cellular phones while the powered scooter is turned on.
2. Be aware of nearby transmitters such as radio or TV stations and try to avoid coming close to
them.
3. If unintended movement or brake release occurs, turn the powered scooter off as soon as it is
safe.
4. Be aware that adding accessories or components, or modifying the powered scooter, may make it
more susceptible to interference from radio wave sources
(Note: It is difficult to evaluate the effect on the overall immunity of the powered scooter).
5. Report all incidents of unintended movement or brake release to the powered scooter
manufacturer, and note whether there is a radio wave source nearby.
TURN OFF YOUR POWERED SCOOTER AS SOON AS POSSIBLE WHEN EXPERIENCING
THE FOLLOWING:
‧ Unintentional scooter movements
‧ Unintended or uncontrollable direction.
‧ Unexpected brake release
The FDA has written to the manufacturers of power scooters asking them to test new products to be
sure they provide a reasonable degree of immunity against EMI. The FDA requires that a powered
wheelchair should have an immunity level at least 20 V/m, which provides a reasonable degree of
protection against more common sources of EMI. The higher the immunity level, the greater the
protection. Your powered scooter has an immunity level of 20 V/m which should protect against
common sources of EMI.
9
ENVIRONMENTAL CONDITIONS
Environmental conditions may affect the safety and performance of your power scooter. Water and
extreme temperatures are the main elements that can cause damage and affect performance.
A) Rain, Sleet and Snow
If exposed to water, your power scooter is susceptible to damage to electronic or mechanical
components. Water can cause electronic malfunction or promote premature corrosion of
electrical components and frame.
B) Temperature
Some of the parts of the power scooter are susceptible to change in temperature. The controller
can only operate in temperature that ranges between 18℉(-8℃) and 122℉ (50℃).
At extreme low temperatures, the batteries may freeze, and your power scooter may not be able to
operate. In extreme high temperatures, it may operate at slower speeds due to a safety feature of the
controller that prevents damage to the motors and other electrical components.
10
WARRANTY
Quality/ Warranty Declaration
Products are to be fit for purpose and of excellent quality and performance. For valid warranty
claims Heartway will, at their discretion, replace/ repair/ refund items mutually agreed to be
defective.
Heartway’s warranty as following:
(1) Frame: two year limited warranty
(2) Electronic Components and Charger: one year limited warranty.
(3) Controllers: one and half year limited warranty
(4) Batteries: 1 year warranty limited
(5) Consumables (wheel tires, arm pads, and seat cushions): not warranted.
Any damage or defect of any nature occurring from the misuse of the product is not to be covered.
The warranty is to start from the date of arrival of our products.
11
ASSEMBLY INSTRUCTION
It is very easy to assemble your PT7 scooter. Please follow the procedure below .
1. Tiller Positioning
Press down the lever, fold the tiller up to vertical position and let it lock into your preferred
position. (See Fig 2)
(Fig.9) (Fig.10)
2. Installing the Seat
(Fig.11)
Lever
Always apply the force
at this position when
adjusting the angle.
Gently push the lever downward
Put the seat axle into the seat post and let it lock
automatically. (See Fig 11)
12
6. Installing the Batteries (you can omit this step if your scooter already assembled with the
batteries)
(Fig.12) (Fig.13)
(Fig.13)
Release the screw
nuts with your hand.
Lift off the shroud from
the base frame gently
﹢/ ﹣pole (Red is positive,
black is negative)
Connect each battery harness
ring terminal to the batteries
terminal posts. Observing
battery positive and negative
polarity color coding
Connected
13
ADJUSTMENTS FOR SEATING CONFORT
A. Armrest Position Adjustment
(Fig.14)
B. Seat Rotation and Position Adjustment
B-1: Seat Rotation Adjustment
→ press down the seat rotation lever
→ rotate your seat by clockwise or counter-clockwise direction.
→ let the lever lock into the corresponding notch. Note: There is a lock in 90°
position whenever you turn by clockwise or counter-clockwise direction.
(Fig.15) (Fig.16)
Turn the round plate and adjust
to your position. Anticlockwise
will move the armrest upward
and clockwise will be downward
14
B-2: Seat Position Adjustment
→ lift up the seat position lever
→ slide your seat backward or forward to your desired position
→ let the lever lock into your preferred position.(See Fig 16)
Note: The distance of adjustment from backward to forward is 150mm.
(Fig 17)
C. Backrest Angle Adjustment
→ lift up the lever located at the left side of the seat
→ adjust the backrest position to fit what is most comfortable for you from 105° to 135°. (See Fig
12)
(Fig.18)
D. Headrest Height Adjustment
→ press the button and lift up or down the headrest to your desired position
→ let the button lock into the corresponding notch. (See Fig 13)
Backrest angle
adjustment
lever
15
Press the button
(Fig 19)
16
OPERATION AND CONTROL PANEL
SCOOTER CONTROL PANEL
(LCD)
SPECIFICATIONS
FOR：JSC501(LCD)
PREPD
BY
CHK
APPR
DATE
TEST
DESN
NAME：
Updated
Functions
070829
Scooter Control Panel (LCD)
New Spec.
061012
DWG NO：
REVISION
RECORD
DATE
PRE
P
CHK
JSC501
17
INDEX
1. APPEARANCE……………………………………………………… ..18
2. FUNCTIONS…………………………………………………………..19~20
2-1. Function Descriptions……………………………………………….19
2-2. Button & LED………………………………………………………20
3. Usage Conditions……………………………………………………… 20
4. Characteristics Test…………………………………………………….21
5. OPERATING INSTRUCTION………………………………………..21~32
5-1. Speed Sensor and Display…………………………………………..21
5-2. High / Low / Turn Speed……………………………………………22
5-3. Power Indication……………………………………………………23~24
5-4. Clock………………………………………………………………..25
5-5. Odometer ………………………………………………………… ..25
5-6. Headlight Control………………………………………………… 26
5-7. Back-up Lamp Control…………………………………………….27
5-8, 9, 10 Indicators and Parking-Lamp Control………………………28
5-11 Malfunction Message…………………………………………… .29
5-12. Power On Self Test………………………………………………29
5-13. Temperature meter (TEMP)……………………………………30
5-14. Reverse Indicator……… ……… ……… ……… ……… … …… 30
5-15. Adjust Buttons………… … … ………… … … … …………… … 31
5-16. LCD Backlight… ……… … … … … …………… … … ………… 32
6. System Configuration… …………… … … … … … ………………… 32
7. Circuit Diagram……………………………………………………32
18
1. APPEARANCE
LCD（Liquid Crystal Display）Scooter Control Panel, TN Mode
Function
Buttons
LED Indication
LCD
ADJ
Buttons
19
2. FUNCTIONS
2-1 Function Descriptions
FUNCTION
SPECIFICATION
1
Speed Sensor
7 Segment display (2.5 digits +1 decimal) + “km/h / mph” symbol
2
High / Low / Turn
Speed
Indicated as “H” and “L” symbols
3
Power Indicator
Battery remaining capacity and charging indicator
(6 squares + Battery Icon)
4
Clock
Hour / Minute / Second display and setting
5
Odometer
ODO (99999 km max), TRIP (99.9 max)
6
Main-Beam
(Headlight)
“Power-saving” mode, Blue LED
7
Back-up Lamps
“Brake / Reverse” modes, Orange LED
8
Right-Indicator
Flash mode, Green LED
9
Left-Indicator
Flash mode, Green LED
10
Parking Lamp
Including “Reverse Mode”, left- indicator and right-indicator
flashing simultaneously, Red LED
11
Malfunction
Message
Malfunction code:
7 Segment display (1digit ) + Warning symbol + Red LED
12
Power-on Scan
All LED turn on
13
Temperature
(TEMP) Gauge
“C / F” modes
14
Reverse Light
“Reverse” symbol flashing
20
2-2 Button & LED
FUNCTION
SPECIFICATION
Buttons
“MODE” switch
Function set
Left-Indicator control
Right-Indicator control
Parking Light control
Headlight control
High / Low speed switch
Back-up lamps control
Horn
LED Indicators
Left-Indicator (Green)
Right- Indicator (Green)
Parking (Red)
Headlight (Blue)
Warning (Red)
Back-up lamp (Amber)
LCD Backlight
Illumination: 700 mcd min (Orange color)
LOGO Backlight
Blue color
Connecter
CON1: 20PIN
3. Usage Conditions
ITEM
SPECIFICATION
Voltage
DC 24 V
Operation Voltage
DC 16 ~32 V
Storage Temperature
-40C ~ 90C
Operation Temperature
-25C ~ 55C
Meter Angle
at Handle Cover
30 of elevation while scooter assembly
(LCD orientate to six o’clock)
SE
T
M
O
D
E
21
4. Characteristics Test
General Characteristic Performance Test (20 5℃)
Hardware Circuit:
ITEM
SPECIFICATION
RESULT (n = )
Lowest Operation
Voltage
16V max
V
Consuming Current
(V
B
= 24.0V)
Dynamic: 200 mA max
-- Backlight and LED light status
Static: 5 mA max
-- Key OFF status
mA
mA
5. OPERATING INSTRUCTION
5-1. Speed Sensor and Display
ITEM
SPECIFICATION
Operation Features
Speed detection by speed sensor from transaxle with
conversion at 1400rpm equal to 60km/h.
Tolerance
15~20%
Digits range
≤ 19.9: 0~19.9
> 19.9: displayed by integer “20~199” (199 max)
Display Switch Button
Initial setting at km/h, switch to MPH by MODE and
SET buttons
22
5-2. High / Low / Turn Speed
ITEM
SPECIFICATION
Operation Features
(1) Switch High / Low speed by pressing button once.
(TRN as control signals)
Press one time: High-speed <<--->> Low-speed
(with memory storage).
(2) Take exterior turn-switch as determinant signal
(TRN as control signals).
Symbols on LCD
＂H＂symbol means “High Speed”:
S P E E D
＂L＂symbol means “Low Speed”:
S P E E D
＂L＂symbol flashing means “Turn Speed”:
SPEED SPEED
Flicker Frequency
1 sec.
23
5-3. Power Indication
ITEM
SPECIFICATION
Battery
Remaining
Capacity
Remaining
Capacity (%)
Voltage (V)
Scale Bar
100
(6)
＞ 25.42
85
(5)
≦ 25.42
70
(4)
≦ 25.12
55
(3)
≦ 24.78
40
(2)
≦ 24.42
30
(1)
≦ 23.88
and Flashing
20
Low-power
Warning
Warning LED Flashing
Flicker
Frequency
2 sec.
Operation
Characters
(1) Scale status only decrease, won’t increase.
(2) When the remaining capacity was less than 30%, warning sound
(“Be-Be” two short sounds) act at 5 seconds intervals.
While (a) Key Off (b) Charging Mode (c) Sleep Mode, warning
sound released.
24
ITEM
SPECIFICATION
Charge
Indication
Remaining
Capacity (%)
Voltage
(V)
Scale Bar
40
(2)
＜ 25.44
55
(3)
＞ 25.44
70
(4)
＞ 26.18
80
(5)
＞ 26.92
90
(6)
＞ 28.5
100
(7)
Increase
Frequency
0.5 sec.
Operation
Character
(1) Scale status only decrease, won’t increase.
(2) Take the PIN3(CH3) of charger as determinant signal, enter「Charging
Mode」when CH3 grounding (L), not only “KEY ON” or “KEY OFF”.
Remarks
Above scale bar status only for reference, must take the indicator of charger
as the precise diagnosis.
25
5-4. Clock
ITEM
SPECIFICATION
Tolerance (per day)
±2 sec.
Initial Setting Value
『Hour：Min』mode :『AM 12:00』
『Hour : Min』Setting
(12-Hour format)
Display range : AM12:00 ~ PM11:59
AM
PM
:
mile
km
When『Hour』is between 1 and 9 o’clock, displayed at 1~9.
5-5. Odometer
ITEM
SPECIFICATION
Operation Features
Odometer detected by the signal of Opto Coupler then converts into
distance.
Display Switch
Button
「km/h」 means the odometer displayed as kilometer.
「mph」 means the odometer displayed as mile.
Accumulative
Display [ODO]
(1) Display Range:00000~99999
AM
PM
:
mile
km
(2) Once the total mileage up to 99999km or 62149mile
(99999÷1.609mile), the counter will restart from “00000”.
TRIP Counter
(1) Display Range：00.0~99.9
AM
PM
:
mile
km
(2) When over 99.9km, display stop counting
(won’t restart from “00.0”).
Operation status
(1) Odometer indication display on ODO mode when Power On,
then switch to TRIP mode after 5 seconds.
(2) TRIP can be reset to “00.0”.
26
5-6. Headlight Control
ITEM
SPECIFICATION
Operation Feature
Take exterior headlight switch as determinant signal.
(1) Switch on/off the head light by pressing button once,
then LED will turn on/off simultaneously.
(2) LCD backlights turn on / turn off with head light.
Power Saving Mode
When motor stop, the modulation down to 30% (Headlight)
When motor act, 100% output power (Headlight)
Usage Condition
While (a) KEY OFF (b) Power-Saving mode (c) Sleep mode , all
functions closed.
Determinant
Condition
(1) 2.2V＞WIP＞2.8V ( 100% Full-power )
(2) 2.2V＜WIP＞2.8V ( 100% Full-power )
(3) Full / Half power switch at real time.
(4) The determination of “Reversing Mode” need to consider the
motor direction and panel setting.
Remarks
(1) Loop Load: 24V/50W max
(2) With “short circuit” and “overload” protection
27
5-7. Back-up Lamp Control
ITEM
SPECIFICATION
Operation Feature
Take exterior back-up lamp switch as determinant signal.
(1) Switch on/off the head light by pressing button
once, then LED will turn on/off simultaneously.
(2) LCD backlights turn on / turn off with head light.
(Control Mode)
Brake-lamp Mode
Reversing-lamp Mode
When motor changes from act (go forward) to stop, the lamp
reinstated after flashing for 3 sec.
Determine as “Reversing Mode”, back-up lamp keep flashing.
Reverse warning sound can be set by panel ( Turn on / Turn
off)
Usage Condition
While (a) KEY OFF (b) Charging Mode (c) Sleep Mode, all
functions closed.
* Brake-lamp & Reversing-lamp Mode won’t be limited by
Back-up lamp switch on or off.
Flicker Frequency
1 sec.
Determinant Condition
(1) 2.2V＞WIP＞2.8V ( 50% Half-power )
(2) 2.2V＜WIP＞2.8V ( 100% Full-power )
(3) Full / Half power switch at real time.
(4) The determination of “Reversing Mode” need to consider
the motor direction and panel setting.
Remarks
(1) Loop Load : 24V/50W max
(2) With “short circuit” and “overload” protection
28
5-8, 9, 10. Indicators and Parking-Lamp Control
ITEM
SPECIFICATION
Operation Feature
Take exterior left-right indicators and parking-lamps switch as
the determinant signal.
Control Mode
(Left-direction lamp)
(Right-direction lamp)
(Parking lamp)
Press button once, the right-indicator and turn off,
left-indicator and flashing, warning sound act.
Press again to turn off left-indicator.
Press button once, the right-indicator and turn off,
left-indicator and flashing, warning sound act.
Press again to turn off left-indicator.
Press button once, turn on, right-left indicators and
flashing , warning sound act . Press again to
turn off the Parking lamp function.
Usage Condition
While (a) KEY OFF (b) Charging Mode (c) Sleep Mode, all
functions closed.
Flicker Frequency
1 sec.
Warning Sound
Frequency
One short “Bi” sound per second
Determinant Condition
Left-Right indicators have priority to Parking lamp.
<Ex.>
If “Parking lamp” turned on already, now you start “Right
indicator” function, the flashing indicator lamps will change
from both side (left & right) to right side, and the “Parking
lamp” function will be closed.
Remarks
(1) Load circuit for left-direction light: 24V/50W max
(2) Load circuit for right-direction light: 24V/50W max
(3) With “short circuit” and “overload” protection
29
5-11. Malfunction Message
ITEM
SPECIFICATION
Operation Feature
Take the connector pin (KEY) of controller as determinant signal,
then converts it into digital code.
Usage Condition
When the controller send out an error message, red LED flashing
with controller signal at same time, the “Error message code” will
show on LCD.
mph
km/h
Flicker Frequency
1 sec.
Controller
message
(Flicker)
Message
code
symbol
LED
(Flicker)
Status
1
--
--
Flashing,
opposite to
controller
message.
Battery needs charge soon.
2
2
On
Low-voltage, needs charge now
3
3
On
Over-voltage
4
4
On
Over-current
5
5
On
Park Brake lost or faulted
6
6
On
Accelerator not align center
7
7
On
Accelerator broken or faulted
8
8
On
Motor broken or faulted
9
9
On
Others
5-12. Power On Self Test
ITEM
SPECIFICATION
Initial Status
When scooter power on, the control panel will go through a self-test
routine; the backlight and all LCD segments will be tuned on for 3
seconds, then switch automatically to the general operation mode
(ODO).
30
5-13. Temperature meter (TEMP)
ITEM
SPECIFICATION
Operation Feature
Temperature detected by temperature sensor (NTC) from
transformation with signal.
Tolerance
2C
Display Range
-20C ~50C
-4F ~122F
Display Switch
Button
When display C, degree stand for Celsius thermometer
When display F, degree stand for Fahrenheit thermometer
5-14. Reverse Indicator
ITEM
SPECIFICATION
Operation Feature
Take exterior forward / backward switch as determinant signal.
Power Saving Mode
When switch direct to “forward”, no symbol on LCD.
When switch direct to “backward”, symbol flashing on
LCD.
Flicker Frequency
1 sec.
AM
PM
:
mile
km
31
5-15. Adjust Buttons
ITEM
SPECIFICATION
Button
“MODE”
switch
Function set
General Display
Mode (TRIP)
Press SET for 3 seconds to reset TRIP at “00.0”.
Setting Mode
Press MODE and SET simultaneously for more than
2 seconds. to enter “Setting Mode”, then 『Hour：MIN』start
flashing.
(1) When『Hour』flashing:
Press SET to increase of number, then press
MODE to enter “Setting Mode” of 『MIN』.
(2) When『MIN』flashing:
Press SET to increase of number, then press
MODE to enter “Setting Mode” of 『km/h & mph』.
(3) When 『km/h』 or 『mph』flashing
Press SET to choose “km/h” or “mph” type, then
press .MODE to enter “Setting Mode” of 『C / F』
(4) When『C』or『F』flashing
Press SET to choose C or F .
Escape from Setting
Mode
Under setting mode, if below situations happened, will auto
save the last setting value then escape to general operation
mode.
(1) No any operation of ADJ button for 20 sec.
(2) Press MODE and SET at same time for more
than 2 sec.
Operation Status
(1) 『Hour：Min』,『km/h』or『mph』,『C』or『F』
offer Cyclical Switch function.
(2) When adjusting 『Hour：Min』, press SET to increase
number, if press SET for more than 2 seconds, the
number will increase continuously until button released,
setting value with Cyclical Switch function (only 2
seconds from 0 to 9).
* If『Hour』less than 10, the denary “0” doesn’t display.。
Remarks
Button tones: one short “Bi” sound
SE
T
M
O
D
E
32
5-16. LCD Backlight
ITEM
SPECIFICATION
LCD Backlight
When pressing MODE and SET buttons, the backlight will
be turned on voluntarily and turned off No any operation of ADJ
button more than 5 sec.
6. System Configuration
ITEM
SPECIFICATION
Controller
Ds162K01 Series
Charger
CTE 8A
Battery
WP12280 *2 (Series connection)
WigWag
CTE NCW-K001
Bulb
24V / 50W max
Tire-Diameter
Circumference
Tire diameter circumference of ____ mm
7. Circuit Diagram
33
BATTERIES & CHARGER
BATTERY
We recommend that you use deep-cycle batteries that are sealed and maintenance- free for your
power scooter. Both sealed lead-acid ( SLA) and gel cell are deep-
cycle batteries and are similar in performance. Deep-cycle batteries are specially designed to
provide power, drain down, and then accept a relatively quick recharge. Lead-acid batteries
should be charged as often as possible.
Specification of the battery that we recommend:
Type:
Size:
Voltage:
Amp Hours:
Deep –cycle sealed lead-acid or gel cell
80AH
12V each
80 amp hours
Depending on the use, terrain and driving conditions, the batteries will provide a range of 32
miles of travel. However, even if the power scooter is not in use, we recommend that the
batteries be charged periodically.
Note:
→Do not use any automotive batteries. They are not designed to handle a long, deep
discharge and also are unsafe for use in power scooter.
→The useful life of a battery is quite often a reflection of the care it receives.
Note: Display a charging battery
Display battery recharging is in process.
Battery capacity icon
When battery charging is in progress the LED display (increases from the lowest scale to the
highest scale in a repeat action.)
Battery capacity display method:
100% 80% 60% 40% 20%
34
(voltage >28.19V) (voltage > 27.82V) (voltage >27.45V) (voltage > 25.71V) (voltage < 25.71V)
* Recharge battery only when the key is in off position. When indicator is showing low status,
this confirms battery needs recharge.
Note:
→Always charge your batteries in well ventilated areas.
→The charger is intended for indoor use only. Protect from moisture.
→For maximum performance , it is recommended that you replace both batteries at the same
time if the batteries are weak.
→If the vehicle will not be used for a long period of time, arrange to have the batteries
recharged at least once every month to avoid deterioration of the batteries..
According to the battery type and condition of the batteries, they usually can be fully charged
in 4-10 hours. This will be indicated when the status light in the battery charger side panel
turns green. Charging the battery longer will not harm the battery. We recommend that you
charge the batteries for 8 to 10 hours after daily use.
35
Battery Charger Instruction
1.APPEARANCE
Important!
Make sure voltage input is correctly selected for your location (110V or 220V) and adjust
manually.
2. SPECIFICATION
Item
BATTERY CHARGER (SWITCHING MODE)
Model
4C24080A
Output Current(DC)
8A±5%
Charging Voltage(DC)
28.8V
Floating Voltage(DC)
27.6V
Input Current (AC)
3.8A max.
Input Voltage(AC)
100 ~ 240 V 50/60Hz
Efficiency
AC-DC 85% min
Operating Temperature
0°C ~ 40°C
Switching Method
SWITCHING MODE
Charging Method
Constant current two stage constant voltage
Battery
Application
24V Lead Acid Rechargeable Battery (26Ahr ~ 75Ahr)
Output Detection
1.Short Circuit Protection
2.Reverse Power Protection
3.Overheat Protection
4.Charging Plug Protection
Power Cord
Output Plug to Battery
Indicator :
Green Flash : Power On
Orange Flash : Pre Charge
Orange : Charging
Green&Orange Flash : Charged 80%
Green : Full Charge
Red Flash：Defect
8A
36
Operating Humidity
20％ ~ 85 %
Measure
L 185mm×W 130mm×H 195mm
Weight
1.7K g
Color
Blue
3. CHARGER OPERATING INSTRUCTION
(1)Make sure the battery charger output voltage is the same as the connecting battery.
(2)Plug in the power cord. LED indicates green flash when AC power on.
(3)Connect the battery charger to the battery.
(4)Start charging ; please refer to 4. LED INDICATION
4. LED INDICATION
(1)Green Flash：Power on
(2)Orange：Charging
(3)Orange Flash：Pre charge
(4)Green&Orange Flash：Charged 80%。
(5)Green：Full charged(Floating charge)。
(6)Red Flash：Defect
5. TROUBLE SHOOTING
(1) If green indicator is off：
․Check AC input. If it works normally, the battery charger may be defect.
(2) If green indicator keeps flashing , can’t turn to charging indication：
․Check if the battery connect successfully.
․Check if the output connection is short or open.
․If the battery connection is normally , the battery charger may be defect.
(3) If red indicator keeps flashing ：
․Check if the battery connection is reversed.
․Check if the output connection is short or open.
․Check if the environment temperature is too low (0
o
C)
․If the red indicator still keeps flashing , the battery charger may be defect .
(4) Charging indicator (orange) can’t turn to green：
․The battery might defect , please stop charging and have the battery be repaired.
(5) If the charging indicator (orange) turns green (fully charged) immediately：
․The battery may be in well-charged condition
․If the battery is not fully charged, the battery may be defect .
6. CAUTION
(1) Before using the battery charger, read all instructions and cautionary markings.
(2) Use the battery charger in a well-ventilated area
(3) To avoid the risk of injury, charge only lead-acid or gel cell type rechargeable batteries.
(4) Please turn off the power after charging
37
9. EMC statements
This portion of the content will provide the user with basic information that
describes the problems with EMI, known sources of EMI, protective measures
either to lessen the possibility or exposure or to minimize the degree of exposure,
and suggested action should unexpected or erratic movement occur.
Caution: It is very important that you read this information regarding the possible
effects of electromagnetic interference on your electric P17RT WHEELCHAIR.
■ ELECTROMAGNETIC INTERFERENCE (EMI) FROM RADIO WAVE
SOURCES
Powered vehicle may be susceptible to electromagnetic interference (EMI), which
is interfering electromagnetic energy (EM) emitted from sources such as radio
stations, TV stations, amateur radio (HAM) transmitters, two-way radios, and
cellular phones. The interference (from radio wave sources) can cause the
powered vehicle to release its brakes, move by itself, or move in unintended
directions. It can also permanently damage the powered vehicle’s control system.
The intensity of the interfering EM energy can be measured in volts per meter
(V/m). Each powered vehicle can resist EMI up to a certain intensity. This is
called its “immunity level”. The higher the immunity level the greater the
protection. At this time, current technology is capable of achieving at least a 20
V/m immunity level, which would provide useful protection from the more
common sources of radiated EMI. This powered vehicle model as shipped, with
no further modification, has an immunity level of 20 V/m without any accessories.
There are a number of sources of relatively intense electromagnetic fields in the
everyday environment. Some of these sources are obvious and easy to avoid.
Others are not apparent and exposure is unavoidable. However, we believe that
by following the warning listed below, your risk to EMI will be minimized.
38
The sources of radiated EMI can be broadly classified into three types:
1. Hand-held portable transceivers ( transmitter-receivers with the antenna
mounted directly on the transmitting unit.
Examples include: citizens band (CB) radios, “ walkie talkie”, security, fire, and
police transceivers, cellular telephones and other personal communication
devices.
Note: some cellular telephones and similar transmit signal while they are ON,
even when not being used;
2. Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances and taxis. These usually have the antenna mounted on the outside
of the vehicle; and
3. Long-range transmitters and transceivers, such as commercial broadcast
transmitter (radio and TV broadcast antenna towers) and amateur (HAM) radios.
Note: Other types of hand-held devices, such as cordless phones, laptop
computers, AM/FM radios, TV sets, CD player, and cassette players, and small
appliances, such as electric shavers and hair dryers, so far as we know, are not
likely to cause EMI problems to your powered vehicle.
■ POWERED VEHICLE ELECTROMAGNETIC INTERFERENCE (EMI)
Because EM energy rapidly becomes more intense as one moves closer to the
transmitting antenna (source), the EM fields from hand-held radio wave sources
( transceivers) are of special concern. It is possible to unintentionally bring
high levels of EM energy very closer to the powered vehicle’s control system
while using these devices. This can affect powered vehicle movement and
braking. Therefore, the warnings listed below are recommended to prevent
possible interference with the control system of the powered vehicle.
■ WARNINGS
Electromagnetic interference (EMI) from sources such as radio and TV stations,
amateur radio (HAM) transmitters, two-way radios, and cellular phones can affect
powered vehicles and motorized wheelchair. Following the warnings listed
below should reduce the
24
39
chance of unintended brake release or powered vehicle movement, which could
result in serious injury.
1. Do not operate hand-held transceivers-receivers), such as citizens band (CB)
radios, or turn ON personal communication devices, such as cellular phones,
while the powered vehicle is turned ON;
2. Be aware of nearby transmitters, such as radio or TV stations, and try to avoid
coming close to them;
3. If unintended movement or brake release occurs, turn the powered vehicle
OFF as soon as it is safe;
4. Be aware that adding accessories or components, or modifying the powered
vehicle, may make it more susceptible to EMI ( Note: There is no easy way
to evaluated their effect on the overall immunity of the powered vehicle);
and
5. Report all incidents of unintended movement or brake release to the powered
vehicle manufacturer, and note whether there is a source of EMI nearby,
■ IMPORTANT INFORMATION
1.20 Volts per meter ( V/m) is a generally achievable and useful immunity
level against EMI ( the higher the level, the greater the protection);
2.This product has an immunity level of 20 V/m without any accessories and
connected to it.
25
40
Assembling drawing
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
26
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
FRONT TILLER COVER
1
2
TILLER FRAME
BUZZER
3
4
RUBBER DUST COVER
5
TILLER RAM MECHANISM
HANDEL CAP
6
7
HANDEL GRIP
BRAKE LEVER
8
9
REAR VIEW MIRROR
REAR TILLER COVER
10
11
CONTROL PANEL
FR SWITCH
12
13
POTENTIOMETER COMBINATION
14
WIGWAG
WIGWAG PAD
15
16
FRONT BASKET
FF COVER
17
18
FRONT BASKET CAP
19
HEADLIGHT
HEADLIGHT BRACKET
20
LOCATOR
21
22
SPEED METER
FRONT HUB
23
24
FRONT TYRE
BEARING
25
26
FRONT AXLE
CHARGER
27
28
FR COVER
FORK
29
30
SPEED SENSOR
MAIN FRAME
31
32
REAR FENDER
REAR BASKET
33
34
BATTERY
SIDE COVER R
35
36
REAR COVER
PLUG(R,L)
37
38
DISK BRAKE SET
TRANSAXLE
39
SUSPENSION BRACKET
40
41
REAR HUB
REAR TYRE
42
43
BATTERY CAP
SIDE COVER L
44
45
FLOOR
REAR SUSPENSION
46
47
RELEASE LEVER
REAR BUMPER
48
49
LAMP BASE
REAR INDICATOR
50
51
LAMP CAP
52
SEAT SLIDING POST
SEAT BASE
53
54
SEAT SLIDING RAIL
CAPTAIN SEAT ASM
55
PT7
41
Assembling drawing
PF7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
26
28
29
30
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
FRONT TILLER COVER
1
2
TILLER FRAME
BUZZER
3
4
RUBBER DUST COVER
5
TILLER RAM MECHANISM
HANDEL CAP
6
7
HANDEL GRIP
BRAKE LEVER
8
9
REAR VIEW MIRROR
REAR TILLER COVER
10
11
CONTROL PANEL
FR SWITCH
12
13
POTENTIOMETER COMBINATION
14
WIGWAG
WIGWAG PAD
15
16
FF CAP
FF COVER
17
18
FRONT BUMPER
19
HEADLIGHT
HEADLIGHT BRACKET
20
TURNING COUPLING
21
22
SPEED METER
FRONT HUB
23
24
FRONT TYRE
BEARING
25
26
FRONT AXLE(R,L)
CHARGER
27
28
FR COVER
SUSPENSION SPRING
29
30
SUSPENSION ARM(R,L)
MAIN FRAME
31
32
REAR FENDER
REAR BASKET
33
34
BATTERY
SIDE COVER R
35
36
REAR COVER
PLUG(R,L)
37
38
DISK BRAKE SET
TRANSAXLE
39
SUSPENSION BRACKET
40
41
REAR HUB
REAR TYRE
42
43
BATTERY CAP
SIDE COVER L
44
45
FLOOR
REAR SUSPENSION
46
47
RELEASE LEVER
REAR BUMPER
48
49
LAMP BASE
REAR INDICATOR
50
51
LAMP CAP
52
SEAT SLIDING POST
SEAT BASE
53
54
SEAT SLIDING RAIL
CAPTAIN SEAT ASM
55
32
31
56
57
56
STEM
FRONT BUMPER
57
BRACKET
42
WARNING!!
1) Please beware once the bi-bi sounds alarm to indicate the status of low battery. Conservatively
speaking, the mobility is able to reach the maximum traveling distance up to 10 kilometer once
the bi-bi sounds exist. Please understand we don’t recommend the user to continue riding once
the status of low battery is shown.
2) Once the bi-bi sounds exist, which means there is only 30% of battery energy left. Please take
actions to recharge the batteries immediately.
3) We strongly recommend that the user must recharge the battery whenever the status of low
battery is alarming. Otherwise, it will seriously cause the battery to over-discharging status and
damage the life of battery. The consequence of the status of the battery over-discharging will
result in damage to battery recharge -performance. The battery recharge-performance will
decline by 15% whenever the over-discharging occurs.
… 40

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

HEARTWAY-PF7

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw HEARTWAY PF7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van HEARTWAY PF7 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info