665733
13
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
13
SMARTMIG 110
EN
INSTALLATION – PRODUCT OPERATION
DESCRIPTION
Thank you for choosing this machine. To get the best from your machine, please read the following carefully :
The SMARTMIG 110 is a traditional machine for semi-automatic welding of ux cored wire only (AC current).
Adjustment and Setting of this machine is easy with its SMART feature.
ELECTRICITY SUPPLY
This machine is tted with a 16A socket type CEE7/7 which must be connected to a single-phase 230V (50 - 60 Hz)
power supply tted with three wires and one earthed neutral.
The absorbed effective current (I1eff) is displayed on the machine, for optimal use. Check that the power supply and
its protection (fuse and/or circuit breaker) are compatible with the current needed by the machine. In some countries,
it may be necessary to change the plug to allow the use at maximum settings.
DEVICE PRESENTATION (FIG-I)
1- Wire speed regulator
2- Control panel and table for SMART feature
3- Power Switch Off/On
4- Voltage selection
5- Power cable
6- Fixed torch
7- Fixed earth cable
8- Drive Reel
9- Wire Reel Support
10- Handle
SEMI-AUTOMATIC WELDING FOR STEEL (FIG-II)
This machine can only weld with no gas wire of Ø0.9 (no gas ux cored wire)
Using no gas wire does not require a gas supply
This machine is supplied to work with a Ø0.9 no gas wire. The contact tip, the rollers, the torch liner are made for this
use. The product is equipped with a two Ø0.9 grooves roller. One is U shaped (recommended for no gas wire) and the
the other is V shaped.
The SMARTMIG 110 is recommended for welding steel 1 to 2mm thick. For thicker sheets, up to 4mm, the assembly
will require several passes.
This welding process requires a slow speed in order to obtain a good quality welding bead.
Warning : The current circulates in the torch and can create a welding arc without pressing on the trigger.
Watch a demonstration video of the SMARTMIG 110 on YouTube.
https://www.youtube.com/watch?v=lvqBXjqbAUk
PROCESS OF REEL AND TORCH ASSEMBLY (FIG-III)
Remove the Nozzle (g III-E) from the torch by turning clockwise and then remove the contact tip, leaving the sup-
port
and the spring on the torch (g III-D).
• Open the door of the machine
FIG III-A : Position the reel on to the support.
• Adjust the reel break (1) to avoid reel movement tangling the wire when welding stops. Be careful not to tighten
too much - the reel must rotate without straining the motor.
• Tighten the plastic screw (2).
FIG III-B : Installing the drive roller.
FIG III-C : To select the adjustment of the drive rollers, proceed as follows :
• Loosen the drive roller knob as far as possible.
• Insert the wire until it exits the other side by about 2cm, tighten the knob again slightly.
• Start the motor by pressing the trigger of the torch.
• Tighten the knob (g III-C) whilst pressing the trigger until the wire starts to move.
Nb : When welding with Aluminium, use the minimum possible pressure to avoid crushing the wire
• Leave approximately 5cm of wire out of the end of the torch, then attach the contact tip suitable for the wire used,
and then the nozzle (g III-E).
The SMARTMIG 110 can accommodate 100mm diameter wire reels.
Smartmig 110
No Gas 0.9 (086104)
DIRECTIONS FOR USE (FIG IV)
The SMARTMIG feature allows you to adjust the voltage and the wire speed.
• The voltage (button A/ B)
• Wire speed - adjust the regulator (1) to the colour zone indicated.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys SMARTMIG 110 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys SMARTMIG 110 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info