665816
15
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
15
PROMIG
EN
Move through the different functions with the «MODE» button (2).
F06: Burn back adjustment. This function enables to avoid the wire to stick to the contact tip at the end of your weld. The adjustment
range of this product is between -10ms to 70ms with the buttons TYPE (-) and WIRE(+).
F07 : Post gaz adjustment Adjustment on how long the gas protects the welding pool at the end of the weld. The adjustment range
is between 0ms to 950ms with the buttons TYPE (-) and WIRE(+).
EXPERT SETTING (STANDARD EN 1090)
In order to comply with EN1090, the product supports WPS (Welding Procedure Specication) and helps to achieve WPQR (Welding
Procedure Qualication Record). It is possible to calibrate the voltage, the current and the wire speed of the product. Warning: the
calibration must be done by GYS or its qualied distributor. Required equipment : Dummy load (ref: 060418), tachometer (ref:
053953), voltmeter and ammeter (ref: 053984).
1/ Voltage and current calibration:
The functions F00 (voltage) and F01 (current) are adjustable through the hidden menu. These functions are available by pressing the
«MODE» button for 3 seconds. The setting range varies from -20% to +20%, by 1% step.
2/ Wire speed calibration:
WARNING: To display the wire speed, a calibration is required for each welding conguration.
The functions F02 (internal motor) and F05 (sparated wire feeder) are adjustable through the hidden menu (you can access it by
pressing the MODE button for 3 seconds) The setting range varies from -20% to +20%, in 1% increments.
To exit hidden menus, move through the different functions with the MODE button until you see «END».
«SYNERGIC» MODE (FIG-V)
With this function, there is no need to adjust the wire speed.
• Put the wire speed potentiometer (4) in the middle of the« Optimal synergic » zone. • Select:
-The wire type (3)
-The wire diameter (3)
-The power (switch on the front panel), to select the right position in accordance with the thickness of the part to weld, please refer
to the table «Synergic mode» (g. VI). From this combination, the device determines the optimal wire speed and the device is ready
to weld. It is also possible to adjust the wire speed if necessary by adjusting the potentiometer (4) + or – manually. A memory of
the latest welding congurations is made and is recalled each time the machine is switched on or each time a trigger of one of the
torches is pressed.
RISK OF BLESSING RELATED TO MOBILE COMPONENTS
The wire feeders contain moving parts that may catch hand, hair, clothes or tools which can lead to injuries! Take extra
care.
• Do not place your hand on mobile/pivoting/wire feeding parts of the machine!
• Make sure that all panels remain closed when in use !
Do not wear gloves when setting up the wire and changing the wire reel.
ADVICE AND THERMAL PROTECTION
• The product must not be carried by its handles, torch supports or the upper panel but by the underside of the product. The gas
bottle must not be attached to the product during movement.
• Respect the basic rules of welding.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Leave the device connected after welding to allow cooling.
• Thermal protection: The light turns on and the cooling duration is a couple of minutes inuenced by the ambient temperature
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys PROMIG 400-4S DUO DV bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys PROMIG 400-4S DUO DV in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 2,81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info