665823
19
Verklein
Vergroot
Pagina terug
1/50
Pagina verder
19
NEOPULSE 270-T1 / 270-T2 / 300
EN
PERFORMANCE
NEOPULSE 270-T1 / 270-T2 NEOPULSE 300
400V - 3~
230V - 3~
(Neopulse T2 only)
400V - 3~ 230V - 3~
X / 60974-1 @ 40°C
(T cycle = 10 min)
20% 60% 100% 40% 60% 100% 40% 60% 100% 45% 60% 100%
I
2
280A 190A 170A 220A 190A 170A 270A 240A 200A 240A 220A 200A
U
2
28.6V 23.5V 22.5V 25V 23.5V 22.5V 27.5V 26V 24V 26V 25V 24V
DESCRIPTION
The NEOPULSE is a semi-automatic welding unit; ventilated for semi-automatic welding (MIG or MAG) and can weld
steel, stainless steel and aluminum. Adjustment is quick and easy with its « synergic wire speed » function.
ELECTRICITY SUPPLY
The absorbed effective current (I1eff) shown on the machine is when used at maximum output. Check that the power
supply and its protection (fuse and/or circuit-breaker) are compatible with the necessary current during use.
The device must be placed in such way that the power socket is always accessible.
Do not use an extension cord which has a wire section smaller than 1.5 mm².
The NEOPULSE is supplied with a 16A plug 5 poles (3P+N+PE) 400V CEE17.. It must be connected to a 400 V (3PH)
supply WITH earth and protected by a circuit breaker (16A and 1 differential 30mA).
It can also be used on a 230V network (3Phase + PE), 50/60 Hz, then it will be advised to use the correct 20A plug.
- The machine will warn you if it is connected to a power supply under 360Veff or over 440Veff.
- Protected against overvoltage, the NEOPULSE will switch off automatically.
DEVICES PRESENTATION (FIG 1)
1 Display + incrementing button 8 Toggle switch Wire feed / Gas purge
2 Reel support 9 SD card support
3 Standard or Push Pull torch connection 10 ON / OFF switch
4 Connection for the earth 11 Power supply cable
5 Push Pull torch command connector 12 Cooling unit connector
6 SpoolGun torch command connector 13 Standard or Push Pull torch gas connection
7 SpoolGun torch power connector 14 SpoolGun torch gas connector
SEMI-AUTOMATIC WELDING FOR STEEL / STAINLESS STEEL (MAG MODE)
This device can weld 0.6/0.8/1 mm steel wires and 0.8/1 mm stainless steel wires.
The machine is delivered with Ø 0.8/1 rollers for steel and stainless steel welding. The value visible on the roller when
in place, is the wire diameter currently in use (FIG-3-B).
For Steel or Stainless Steel, you will need to use specic gas - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary
depending on usage. For the specic requirements, seek advice from your gas distributor.
The gas ow for steel is between 8 and 15L / min depending on the environment.
SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE)
This device can weld 0.8/1/1.2 mm aluminium wires.
To weld aluminium, neutral gas “pure Argon” (AR) is required. When choosing gas, ask a gas distributor for advice. The
gas ow in aluminium should be between 15 and 25 L / min depending on the environment.
Things to note when welding with Aluminium
- Rollers: Use rollers specic to aluminium welding (U groove)
- Roller pressure: Set the pressure of the rollers to minimum so as not to crush the wire
- Capillary tube: Do not use a capillary tube when welding aluminium
- Torch: When welding aluminium use a special aluminium torch with Teon sheath to reduce friction. Do not cut the
sheath near the connector! It is used to guide the wire from the rollers.
- Contact Tip: Use the specic Aluminium contact tip corresponding to the diameter of the wire.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys NEOPULSE 300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys NEOPULSE 300 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 5,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info