665820
13
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
13
MAGYS 400-4 / 400 GR / 500 GR / 500 WS
EN
CONTROL PANEL (FIG-4):
Welding mode selection / test (1) :
- 2T: two-stage welding / 4T: four-stage welding.
- SPOT: Spot welding with adjustable spot diame-
ter
- Delay: intermittent welding modes for an opti-
mised operating procedure
2 modes to make easier the setting up of the welding
unit: « Manual » or « Synergic ».
- Test function: The LED switches on when you
push the button (1). Read chapter «Welding unit set-
tings»
Voltage display (9) :
By pulling the trigger (The LED indicates that your
torch is on) the voltage will be displayed according to the
parameters selected.
Power adjustment switch (12): 20 positions for the
Magys 400-4, 400 GR and 30 for the 500 GR / 500 WS.
SPOT / DELAY potentiometer (3): To adjust the wel-
ding time of a point, the size of the point and the time
between each point.
Wire speed setting (2): Potentiometer to adjust the
wire speed. The speed can vary from 1 to 24 m/minute.
Note for the MAGYS 400 GR/500 GR/500 WS: It is pos-
sible to select either the potentiometer of the separate
wire feeder or the generator.
See chapter «wire speed potentiometer» and the sticker
inside the wire feeder
Arc dynamics potentiometer (4): To adjust automati-
cally or manually the arc dynamics.
Metal selection and manual mode (5): Read chapter
«Welding unit settings»
Mode « Synergic » (6): Read chapter «Welding unit
settings»
Welding current display (10): indicates the ampe-
rage (LED « A ») or the thickness (11) recommended
according to the power selected (read « test » function
in the chapter « Welding unit settings »).
Note: « NOP » on the display indicates that the welding
current selected is superior to the one recommended
taking into account the parameters (type and diameter
of the wire).
Wire diameter (7): Select the wire diameter used.
Thermal protection LED (8): Read chapter «Thermal
protection».
WELDING UNIT SETINGS: (FIG-4)
« SYNERGIC » MODE
This function automatically controls the wire speed. There is no need to set the wire speed manually.
- Position the potentiometer (2) in the middle of the « Optimal synergic » zone
- Select: Wire type (5), wire diameter (7), power mode (with the 2 power switches on the front (12)).
From the settings chosen, the unit determines the optimum wire speed and is ready to weld. It is also possible to ma-
nually adjust the wire speed (+ or –) if necessary using the potentiometer (2). The last welding conguration is saved
in the memory automatically (wire diameter, wire type, mode).
« Test » function
Only in the synergic mode, I twill indicate you the thickness you can weld with the parameters
selected without using any gas or wire. These values are calculated on the basis of a welding
on the at surface. Attention: you have current in the torch, so avoid any contact with any
metallic part.
NOTE: If the gas, the wire diameter, and the metal used are different from the ones selected in the synergic mode, you
will need to switch to the manual mode to set up the welding unit.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys MAGYS 500 WS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys MAGYS 500 WS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info