624567
16
Verklein
Vergroot
Pagina terug
1/82
Pagina verder
Clamping Screw Set Up
Grinding
Before the start of grinding, the chain should be conducted
between both the attachment guides
Now, the tooth to be sharpened first should be taken against
the stop. Watch out for the sharpening angle to correspond
to the guides position. The type of the chain to be sharpened
should be determined using the sharpening block provided
or the table p.9. There, you can find out the cutting
thickness, angles and dimensions.
Set the guides to the chain width using the set screw u(A) so
that it is firmly fixed in the clamping screw by clamping lever
control (B).
Set the feed by set screw (E).
On severely worn chains, the lateral position of the chain
guide should be secured with a set screw (D).
Set the top plate angle by means of the set screw (p.3, p. 5)
and it may be also read on the scale (F). The vice angle
should be set up by set screw (G).
G
B
A
D
E
F
Vrcholový řezný úhel
(Top Plate Angle)
Úhel ostří
(Vice Angle)
With the clamping screw adjusted and the vice angle set up
(Notice: RH and LH teeth to be differentiated) and preset the
top plate angle, lead the grinding disk down to the tooth by soft
pushing the supporting strut. The grind depth may be set by
set screw (K).
With clamping lever loosen (B), the set screw is being screwed
or unscrewed (E) until the grinding disk to sharpen will touch
the tooth. During the procedure, pull the chain to the guide (L)
carefully.
(Notice. Wear gloves when performing the job!)
K
L
Some types of saw-chains require that the clamping screw be tilted by 5° - 10° (cf. Table: space Tilt angle).
Note the notches (Fig.9).
Now, the machine may be switched on and the saw-chain grinding may be started by a careful thrust on the grinding disk.
Adjust the pressure as necessary. Mark the start of grinding e.g. with a piece of chalk and grind all the teeth in one direction,
then turn the clamping screw (mind the angle) and grind the teeth in opposite direction.
With warn chains, the lateral guide position (Fig.10, position M) shall be set for the grinding disk not to touch the guide.
Avoid any strong thrust as the teeth might collide and the chain would wear and tear too fast.
Notice : Never grind any driven parts.
16
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gude P 2500 94131 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gude P 2500 94131 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 2,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info