623617
10
Verklein
Vergroot
Pagina terug
1/37
Pagina verder
Training
Use of the unit requires adequate lesson by a professional or
the use of the manual only. Special training is not required.
Technical Data
GWS 450 ECO
Power connection 230 V/50 Hz
Motor output 2,1 kW/P1 (S6/40%)
Speed 2800 U/min.
Ø saw disc 450 x 30 mm
Maximum section 160 mm
Approximate maximum section at
double cutting 200 mm
Cradle width 200 mm
Cradle extension 0-500 mm
Acoustic output level (idling)
measured
guaranteed
96 dB (A)
98 dB (A)
Approximate weight 65 kg
Ordering No. 01837
Transportation and Storage
For a prolonged shutdown, the saw disc and the cradle spring
are recommended to be wiped with an oil-soaked cloth to
protect them from corrosion. Cover the saw with a tarpaulin if
it stands outdoors or at unprotected places. The motor and
the switch should be primarily protected against water.
Residual Hazards and Protective Action
1. Electrical Residual Hazards:
Direct electrical contact:
Defective cable or plug may cause an
electrical shock Wounds cause by conductive
parts on open electrical or defective structural
parts.
Have the defective cable/plug exchanged by a
professional. Use the unit only if connected via a
faulty current switch (FI).
Indirect electrical Contact:
Always unplug before any maintenance.
Operate only with FI switch installed.
2. Mechanical Residual Hazards:
Cutting, incision:
A contact with the rotating saw disc may cause
severe injuries.
Risk of injury by rotating parts
Always be very careful with small pieces to be
worked. Use aids (such as sliding tool or a guide
block/bar). Never touch the disc if it is still moving.
The worn or damaged aid should be replaced
immediately.
Catching, winding:
Loose garments or jewels may be caught by
moving parts. Always wear tight-fitting clothes
and do not wear jewels that could be caught.
3. Noise Hazards:
Impaired Hearing:
Prolonged work with the saw may result in
hearing impairment
Always wear ear protectors
4. Materials and Other Substances Hazards:
Contact, aspiration:
Lungs may be affected by great amount of
dust being formed. Health-hazardous sawdust
emissions from operations without extracting
the dust.
Always wear breathing mask when working with
the unit. Install and use an exhaust equipment.
5. Human Factors Neglect:
Negligent use of personal protection
equipment:
Operating the unit without adequate PPE may
cause severe external/internal injuries
Always wear prescribed protective clothing and work
considerately.
Inadequate local lighting:
Insufficient light is a heavy safety risk.
Provide for sufficient lighting
6. Other Hazards:
Thrown away articles and splashes:
The band or mechanical particles may wound
your eyes in the course of cutting job.
Always wear protection goggles.
Assembly and Initial Operation (Fig. 2, 3, 4, 5 + 6)
Fig. 2 + 3 Install the connector
Fig. 4 + 5 + 6 Blade mount
Saw Disc Replacement on GWS Models (Fig. 4, 5 + 6)
Saw disc replacement on GWS models:
1. Disconnect the power supply.
2. Remove the cotter pin at the end of the cradle setting
rod (Fig. 4), put up the rod and tip the cradle forward
(Fig. 5 ).
3. Lock the disc on the sawdust tank with a screw.
4. Always wear safety gloves at these operations.
5. Release the setting screw using a C-wrench with
caution. The cautiousness is essential as unexpected
lapse of the wrench may result in a severe injury of the
hand!
6. Carefully remove the saw-blade in the upward direction
and put a new blade in the installation procedure is
reverse.
7. When changing or carrying the saw-blade, always hold it
safely and firmly. The disc is heavy at it may be slipping
down. If it falls out of your hands, it may cause severe
injuries. .
8. After the disc replacement, set the cradle so that the disc
distance is 50 mm (Fig. 6).
Caution: Remove the lock screw again!
Caution: Always wear safety gloves when replacing
the disc to avoid accidents.
Initial Operation Safety Instructions
Before putting the machine in operation, check to see
that the machine is connected to the mains, it does not
show any damage and the screwed joints are tight.
Re-check that the power supplying cable does not show
any apparent damage, such as cracks or scraped spots
Check to see that no foreign objects got in the machine
that could be shot out on switching.
Always stand off the direction of shooting out the
objects that were caught by the saw-blade (chips,
pieces of bark).).
It is prohibited to operate the machine being under
influence of narcotics and similar agents such
As alcohol.
Do not use the machine for performing any other works
than those it has been designed for as indicated in this
instruction manual “Working Instructions”
Under any conditions observe our instructions of safety
and accident prevention, putting operation, function,
work and care and maintenance. Variances are possible
upon our written consent only
Never leave the machine without having disconnected
the power supply (unplugging the machine) and having
the machine secured against use by unauthorised
persons.
10
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gude GWS 450 ECO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gude GWS 450 ECO in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info