624755
14
Verklein
Vergroot
Pagina terug
1/50
Pagina verder
1. Rotation axle lubrication if the run gets tight
1.1 Loosen the set nut a put a few drops of the lubricant oil
on the washer and the contact area.
1.2 Remove it and lubricate the rotating axle and contact
areas. NOTICE: Before removing the axle, the saw disc
top cover and the end stop upper part have to be
removed first. The job should be accomplished by a
skilled servicing technician. Mind the position of both the
spring’s ends in the case. Mark it with a piece of chalk to
facilitate re-installation.
2. To provide silent and easy run of the swinging
protective cover control lever, all the metal and plastic
contact areas should be slightly lubricated with sewing
machines oil now and then. Take care not too use
excessive amount of the oil. Sawdust tends to deposit in
the excessive oil and form hard spots.
NOTICE: „Unplug the machine prior to any adjustment or
maintenance. “
Handling Motor
Caution: To avoid any damage of the motor, clean it
(cooling) of the sawdust and dust regularly.
1. Connect the saw to the mains of 230V secured with a 16
A fuse and a protective undercurrent switch. Poor
protection may cause a damage to the motor.
2. If the motor does not start immediately, let the switch go.
UNPLUG .
Check the saw disc for easy run. If it is does run easily,
try restarting again.
3. When the motor stops sudden while cutting is in
progress, push the switch off and unplug the machine.
Release the saw disc from the material cut. Afterwards,
you may finish the job. .
4. Fuses or protection switches may respond to conditions
as follows:
a. THE MOTOR IS OVERLOADED. If the saw
disc is immersed in the material too fast or if the
saw is switched on and off too often, it may
result in the motor overloading or a fault on the
gear.
b. Fluctuations of the mains voltage within a range
of 10% will not pose any risk to normal
operation of the saw. However, if the load is too
high, the voltage on the motor connection
terminals should correspond to the plate data.
5. Many problems of the motor may be caused by loosen
or defective connectors, overloading, undervoltage (the
latter may result from too small cross-section of supply
cables). Always check all the connections, voltage value
and the current consumed.
14
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gude GRK 250-300 LP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gude GRK 250-300 LP in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info