Handleiding Gude GRK 250-300 LP (pagina 11 van 50) (Nederlands, Duits, Engels, Frans, Italiaans)

624755

Verklein

Vergroot

Pagina terug

1/50

Pagina verder

conditions. Any damaged part of the machine should be

immediately repaired or replaced.

 Do not leave the machine running unattended.

Switch the machine off and do not leave it until it

completely stops

 The appliance meets EN 61000-3-11 requirements and

is subject to special connection conditions. That means

that use on optionally selected connection points is

inadmissible.

 The appliance can lead to occasional voltage

fluctuations under unfavourable power conditions.

 The appliance is only designated to be used for

connection points not exceeding the maximum allowed

impedance of Z

max

= 0,233 Ω.

 As a user, you must make sure your connection point on

which you want to use the appliance meets the above-

mentioned requirements – after agreement with your

electricity supplier if necessary.

Trimming Saw Safety Instructions

Steps to be taken prior to the first use:

 Assembly and installation

 Getting familiar with the function and correct operations

of the controls as follows:

 switch on/off

 upper and lower protective cover

 saw shaft and pushbutton on the hand grip lock

 skew setting of the saw head, stop clips and turning

table lock

 Read all the safety information and operating

instructions in this manual and take care to understand

it.

 Observe all the precautionary notices on the trimming

saw.

Before each use:

 Check the saw. If a part is missing, bent or

unserviceable for another reason, if there is a defect on

electrical equipment, switch the saw off and unplug it.

Prior to the following use, replace all the missing,

damaged or defective parts.

 Plan your job to have your eyes, hands, face and ears

protected at any time.

 Wear safety goggles meeting the requirements of DIN

58214. While the machine is in use, various particles

could get in your eyes and cause a permanent visual

impairment. You may buy the safety goggles at the place

where you bought the trimming saw. Using goggles not

in conformity with DIN 58214 may result in a serious

injury in result of a crack of the protection glass.

 When working on a dusty job, wear a dust-proof mask in

addition to the goggles.

 To prevent blocking of the saw disc in the kerfs or

throwing the cut material off:

 Select a saw disc matched to the specific job. Use this

trimming saw for wood and similar materials or soft

metals, such as aluminium.

 The arrow on the saw disc showing the rotation direction

should coincide with the arrow on the saw. The saw disc

teeth should direct downwards on the front of machine

 Make sure that the saw disc is sharp, undamaged and

properly set up. With the machine unplugged, push the

saw head downwards. Turn the saw disc with your hand

a check whether the movement is free. Turn the saw

head to the position at an angle of 45° and repeat the

check. If the disc drags at a place, the head should be

reset as described in Article 6 „Preparation Steps “

 Keep the saw disc and the saw disc flanges faces clean.

 The saw disc flanges should be fitted with the work

shoulder inwards (in the direction of the saw disc)

 The work shoulder side of the flange should tightly fit on

the saw disc flange.

 The flange screw should be fastened manually using a

socket spanner 13 mm.

 Make sure that all the attachment devices and locks are

tight and no component is allowed too much of free

travel.

 Never cut with free hand:

 Press the cut material down to the table and to the

stop all the time so that any swinging and turning is

prevented. No sawdust should collect under the cut

piece.

 Take steps to prevent any move of the piece after it is

cut through (e.g. if it does not touch the support with

its all surface

 For cutting pieces not abutting the plate with their all

surface, use supports, feeding aids or another

machine.

 Make sure that chips will fall away along the side of the

saw disc. If on the contrary, the chips could get stuck in

the disc and it would throw them off.

 Never cut several pieces at a time.

 Take special care when cutting large or very small

pieces or pieces difficu

lt to handle.



Use auxiliary supports (table, holders) for long

pieces that tend to fall down from the table when

unsupported.

 Never use this saw to cut pieces so small that they

cannot be safely held with hand if you put your

index finger on the stop outer edge.

 When cutting pieces of various profile, work so that

the material cannot slip and get jammed in the disc.

The pieces of various profiles should either attach

with all their surface areas or it is necessary to hold

them with a device that will prevent waggling,

turning or slipping during the course of cutting. .

 Round pieces, such as bars or tubes should be

held firmly otherwise, they would spin and there is a

risk of the disc getting stuck. Always clam round

pieces in a proper device.

 No nails or foreign matters should be left in the cut

pieces.

 The viewers should be kept at a safe distance from the

work area and the area behind the saw, where the

sawdust and chips go.

 Never switch the trimming saw before removing all the

things except for the piece to be cut and clamping

devices from the table.

 To prevent hearing deterioration, always wear ear

protectors when working for a longer time.

 To prevent being retracted in the disc,

1. Do not wear gloves

2. Put off any jewellery and wide garments.

3. If your hair is long, wear a hairnet.

4. Roll up the long sleeves above your elbows.

 Unplug the machine prior to any adjusting the end stop

or the saw head, replacement of the disc or accessories

and any other kind of maintenance in order to prevent

any accidents in result of unintentional switching on.

 Do not touch the metal pins of the plug when plugging in

to get protected from the electrical shock.

 Do not use the cable for pulling out the plug from the

socket.

Protect the cable against the high temperature, oil and

sharp edges.

 Never apply detergents or lubricants on this disc, which

still turning.

 To prevent fire, never operate the trimming saw close to

inflammable liquids, vapours or gases

 Avoid any accidents possibly resulting from the use of

improper accessories. Only recommended saw discs

should be used.

While the saw is running:

 Before the first cut, have the saw running idle for a while.

If you hear unusual sounds or feel strong vibrations,

switch the saw off, unplug and find out the cause. Do not

Gude GRK 250-300 LP Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info