Handleiding Gude BTS 4000 ECO (pagina 10 van 35) (Nederlands, Duits, Engels, Frans, Italiaans)

624782

Verklein

Vergroot

Pagina terug

1/35

Pagina verder

Qualification

No special qualification is required for use of the unit except for

detailed direction by a professional.

Minimum Age

Only persons above 16 years of age are allowed to work with

the unit.

Exempted from the provision is the use of the juvenile trainees

if they work in the course of their professional training with an

aim to obtain the skill under a trainer supervision.

Training

Use of the unit requires adequate lesson by a professional or

the use of the manual only. Special training is not required.

Technical Data

Supply connection 230 V

Frequency/Protection type 50 Hz / IP 32

Protection class I

Max. output P

350 W

Motor speed 1450 min

-1

Work area l x w: 190 x 125 mm

Ø sander disk ca: 150 mm

Sander belt dimensions l x w: 914 x 100 mm

Stop inclination: 0-45°

Sander belt inclination : 0-90°

Connection cable: 1,5 m / H05 VV-F

Weight ca: 14 kg

Dimensions l x w x h (mm): 500 x 370 x 330 mm

Ordering No.: 55111

Transportation and Storage

The unit has been designed for stationary use.

Units out of use should be stored in a dry locked room.

Residual Hazards and Protective Action

1. Mechanical Residual Hazards:

 Catching, winding:

Lose garments and jewels may be caught with moving

parts.

Contact with rotating sander disk may result in serious injuries.

 Friction, abrasion:

Always wear tight-fitting garments and do not wear

jewels that might be caught.

Avoid any contact with the sanding means. Use protection

gloves.

2. Electrical Residual Hazards:

 Direct electrical contact:

Defective cable or plug may cause an electrical shock.

Have the defective cable/plug exchanged by a professional.

Use the unit only if connected via a faulty current switch (FI).

 Indirect electrical contactt:

Accidents caused by conductive parts on open or

defective structural parts .

Always unplug for maintenance Use the unit only if connected

via a faulty current switch (FI).

3. Noise Hazard:

 Hearing Impairment:

Prolonged work with the unit may result in hearing

impairment.

Wear ear protectors

4. Materials and Other Substances Hazards:

 Contact, aspiration:

Lungs may be affected by great amount of dust being

formed.

Always wear breathing mask when working with the unit.

5. Human Factor Neglect:

 Neglect us of personal protection equipment:

Operating the unit without adequate PPE may cause

severe external/internal injuries

Always wear prescribed protective clothing and work

considerately.

 Inadequate local lighting:

Insufficient light is a heavy safety risk.

Provide for sufficient lighting

6. Other hazards:

 Thrown away objects and splashes:

In the process of cutting, the blade or mechanical

particles may injure your eyes.

Always wear goggles when working with the unit

Assembly and Initial Operation (Fig. 2)

Mount the unit to four respective points on flat horizontal

ground using suitable screws and check it for firm settlement.

Workbench Alternative Assembly (Fig. 3 and 4)

Fig. 3:

Belt and disc grinding machine 4000 ECO is supplied nearly

completely assembled. It is only needed to shift the table

bracket (Fig.1 – pos. 3) to a given screw (Fig.3 – pos. A) and

to screw it together with an socket wrench.

Fig. 4:

Now, attach the table bracket with the lock screw delivered.

Now, the table is smoothly adjustable.

Initial Operation Safety Instructions

 Mind the safe attachment of the unit on a suitable surface

area.

 Make sure that all the screwed joints are tight.

Procedure

 The assembly of parts should be done in shown order. Be

particular about correct arrangements of structural parts

according to the figures.

 Connect a suitable dust exhauster to the exhaust

connection.

The unit must always be operated with a dust

exhauster. That will prevent excessive dust nuisance

that may be health hazardous and helps to a better

sanding result.

Operation (Fig. 5 and 6)

Fig. 5:

Mind the run direction!

Fig. 6:

By pressing button (I), the unit will switch on. Pressing button

(0), it will switch off.

Change of Grinding Angle (vertical use, Fig. 7, 8 and 9)

Unloosen both the nuts behind the grinding disc using a

forked wrench (size 13)  (Fig. 7).

Set up the required angle of the grinding belt.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Gude BTS 4000 ECO Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info