747993
55
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
55 / 80
33028_mc_28_Teil2_jh
Offset (mixer neutral point)
The dotted vertical line in the middle of the graphic indicates the
position of the mixer neutral point ("offset"). This is the point on the
control travel where the mixer does not affect the control channel.
By default this point is in the control center.
If you select the line under "Offset", the bottom line will show "STO"
and "SET".
Define the position for the offset with the control by selecting “STO”.
Select "SET" and the value is entered using the selection keys.
Setting the curve mixer C9 - C12
Open the display page in the column " ". Mixer guide lines can be
defined for the four curve mixers. These guide lines can be defined
by up to four freely adjustable points between the two endpoints "L"
(low = -100% control travel) and "H" (high = +100% control travel). In
the default settings of the program, 2 support points are already
defined, the endpoints "L" and "H".
Setting support points
Move the control of the mixer input to obtain a vertical line in the
graphic to the right of the display. This line shows the position of
the control. Move the line to the point to the desired support
point. Tap the SET button. A 1 and a percent display appear in the
"Point" line. If necessary, add the further three points.
Support points moving
Move the vertical line with the control of the mixer input to the sup-
port point "L, 1 to 4 or H". The support points will be changed. The
number and the current curve value of this point are displayed.
Activate the value field of the line Point. Then use the selection keys
to change the value to between -125% and +125%.
Trim point function
Alternatively, if the value field is active, select already set points by
ascending or descending with the selection keys. The selected point
is marked in the graphic with a triangle. The selected support point
can then be changed with the selection keys. Tap the ESC button to
exit this trimming function.
Trim offset function
If the value field is active, you can select and change already set ver-
tices by ascending or descending with the selection keys. You can
move an existing curve vertically with the  keys in the range of ±
25%.
Tap the ESC button to exit this trim offset function.
–45%
0%
0%
Input
Output
Point ?
C.Mix 9
normal
Curve off
810
+35%
–55%
Input
Output
Point 2
C.Mix 9
normal
Curve off
810
–55%
–35%
+55%
Input
Output
Point 2
C.Mix 9
normal
Kurve aus
810
–55%
Trim point
+35%
–80%
Input
Output
Point 2
C.Mix 9
normal
Kurve aus
810
–80%
Trim offset
55

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Graupner MC-28 4D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Graupner MC-28 4D in de taal/talen: Engels als bijlage per email.

De handleiding is 17,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info