637250
11
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
11- 20
GR-10C_jh_V1
Initialization of the gyro
Once the model has been switched on, the gyro immediately
becomes active but still needs to be initialised. To initialise the
gyro, keep your model still when you switch it on. The calibra-
tion process can only be performed when the receiver is abso-
lutely still. After 3 seconds in still position you will hear beeps
emitted by all motors. The signal tone can vary depending on
the esc model. These "wiggles" signal that initialisation has been
successful and that calibration is complete. Always wait until the
calibration process has finished before starting to fly the model.
The motors will not start until the calibration is complete.
CAUTION
If the copter is used for long time (>1min) in Acro 3D mode the
receiver can loose its position information and the copter can
move itself out of control. Before switching back to Attitude
mode, hoover the copter for 30 s or land it in Rate mode, so that
the receiver can reset the position.
Special function channel 6
The auto-flip function allows you to flip your copter in a very easy
way. It is essential that you control in Attitude mode (function not
allowed in Rate mode).
The auto-flip function must be controlled by channel 6. For this
program a 2-way switch (e. g. SW1) in the transmitter control
menu on channel 6 with the following values:
Auto-flip function on = Channel 6 > 110%
Auto-flip function off = Channel 6 < 110%
Activate the switch and within 5 sec move the nick or roll stick
to more than 50% of its course, then the copter makes auton-
omously a flip in the selected direction. After the flip it is possible
to have some little position movements (<10°)
Basic settings
Type
Quadro x, Quadro +, Tri L, Tri R
Channel connections to the receiver for the different copter
types.
Connect the speed controllers of the motors to the receiver fol-
lowing the proper scheme (see next page "Connection scheme
of different copter types").
In case of tricopter use only digital servos for servo 4.
Motor direction seen from the top of the copter!
Initialization by switching on
!
Step 2
Basic settings
Multicopter Basis< v >
>Type Quadro X
Mode NORMAL
ONESHOT No
Minpower % 10
Calibr. Posit. No
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Graupner GR-10C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Graupner GR-10C in de taal/talen: Engels als bijlage per email.

De handleiding is 1,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info