782355
7
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Graule Maschinenbau GmbH ,
Robert-Bosch-Str. 7, D-73431 Aalen
Tel: 0049 (0)7361 49511 Fax: 0049 (0)7361 49521, e-mail:info@graule.de
8.7 Selecting and replacing the saw blades
On cross-sectional saws with extension arms only saw blades with negative effective cutting
angle may be used! An effective cutting angle from -3° to -5° is appropriate.
Select a HM-circular saw blade fitting to the material to be cut. See list of accessories.
DISCONNECT THE MAINS PLUG when replacing the saw blade! By using the
handwheel for the elevation adjustment, lift up the saw slide so that the saw blade may run
free above the material supporting table. Pull the saw unit completely forwards and stop it
there by means of the knurled screw at the guide carriage behind the motor. Remove the left
saw blade protection hood. Stop the saw blade by putting across a wood lath and open the
saw blade straining screw to the right. Caution: the straining screw has a left thread! Insert
the saw blade. Place the face chuck in such a way that the locking pin of the saw blade
flange graps into the bore holes of the face chuck. Make sure that the clamping surfaces on
the saw blade flange, saw blade and face chuck are clean and free from dust. Tighten the
straining screw and mount the protection hood.
8.8 Hydraulic feed brake (option)
The hydraulic feed brake prevents the saw blade to be pulled into the cut material. Adjust
the feed speed with the knurled brass screw at the valve block. Select the speed in such a
way that the saw blade can easily cut the material.
The liquid in the feed brake is a drilling oil emulsion with a ratio of mixture 1:40 with
water.
Do not close the screw cap of the liquid container completely, so that the air may stream in
and out. If an insulating air cushion builds up in the tube of the hydraulic feed brake, you
must open the choker screw turning approx. 3 times and pull the tool slide quite to the front
a few times, so that the air cushion will be squeezed out of the tube. Then adjust again the
choker screw.
8.9 Pneumatic saw blade spray appliance (option)
Release the saw blade spray appliance using the lever valve beside the pull handle. Adjust
the spray nozzle by means of the knurled screw at the orifice hood in such a way that there
will be a light smoke-screen on the saw blade. No banked-up water level must build up on
the machine. As to the liquid for the spray appliance, it is a customary coolant and lubricant,
adequately diluted, for metal finishing.
8.10 Pneumatic material tension (option)
The cut material should always be tensed as near as possible to the cutting line. Make always
sure that the cylinder retaining arm never lies on the cutting line. Adjust the clamping
cylinder leaving max. 5 mm air between the cut material and the pulled in thrust piece of the
clamping cylinder. SQUEEZE DANGER! The air pressure must fit the material to be
tensed. The material to be tensed must not be compressed. The use of suitable additions is
recommended. The valve for the pneumatic material tension is on the right in front of the
material supporting table.
8.11 Mitre adjustment
There are adjusting dead stops for 90° and 45° . Intermediate mitres can be adjusted at your
choice according to scales.
Horizontal mitre adjustment: release the back lower clamping lever. The machine may now
be swivelled to the left. To adjust the mitre to the right, pull up the stop pin in the oscillating
crank, so that the 90° cam can be overrun. After adjusting the mitre, the oscillating crank
must be stopped again by means of the clamping lever.
8.12 Elevation adjustment
You can adjust the elevation of the saw blade by means of the handwheel. For this purpose
lightly loosen the wing screws which press on the vertical supports and tighten them again
after adjusting. Adjust the elevation of the saw blade so that it may cut approx. 5-8mm deep
in the wood platform. The depth gauge for this adjustment is on the support block behind
both vertical pillars for the elevation adjustment.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Graule ZS 135 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Graule ZS 135 in de taal/talen: Engels als bijlage per email.

De handleiding is 0.85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info