782355
4
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Graule Maschinenbau GmbH ,
Robert-Bosch-Str. 7, D-73431 Aalen
Tel: 0049 (0)7361 49511 Fax: 0049 (0)7361 49521, e-mail:info@graule.de
position, to prevent pulling forward unintentionally. The saw blade is then perfectly located
in the lower saw blade protecting hood.
The material wooden supporting table with the insert and the vertical back stop shoulder
must always be in good condition. Defective tables and stop shoulders must be replaced.
Return spring device, which withdraws the tool slide into its rear starting position after
a saw cut, must be immediately replaced in case of breakage. The saw must not be operated
when the return spring device is faulty.
The ball-type nipple guide must be cleaned at regular intervals, so that the guiding elements
may run smoothly and the tool slide may be pulled back indipendently into its rear starting
position through the return spring device.
Lower saw blade protecting hood must be correctly set, so that the saw blade is entirely
covered in its lower area. Switch off the machine (disconnect the mains plug!) to remove
residual material fragments which might be got stuck.
CAUTION: Do not operate the machine if parts are damaged! Faulty parts must be
immediately replaced and in the meantime the machine must be stopped!
5. Qualified application.
Circular cross-cut and mitre-box saws type ZS 135 or ZS 170 may only be used for professional
cutting into sections or mitre cutting of following materials: wood with a rectangular or
square cross section, strip cutted panel materials, like particle board, wood core plywood
and Mdf-boards which are made fit for the cutting range, plastic profiles (duroplastic and
thermoplastic) and, in connection with hydraulic feed brakes, hollow extruded aluminium
profiles up to a wall thickness of approx. 4 mm . Profiles must have a safe support. Profile
sections must be adapted to the machining range. The saw blade must match the material to
be cut.
A qualified application also requires that the saw blade has a negative effective cutting
angle.
Any other different application shall be regarded as unsuitable and the manufacturer assumes
no responsibility for resulting damages of any kind. The risk shall be taken by the user alone.
The use of HSS-(high-speed steel) saw blades and cutting-off wheels is not allowed.
The machine must be connected to a large exhaustion plant.
During operation the machine must have a safe location.
A qualified application also requires that the manufacturer meets all specified operation,
maintenance and repair conditions, as well the operation and safety regulations of the
working instructions.
6. Other risks
Owing to the purpose of application of the machine design, the following remaining risks
may arise, even after taking all necessary safety precautions and despite a qualified
application:
Touching the saw blade during the cutting operation.
Slinging away of small wood fragments.
Breaking and slinging out of saw blade parts.
Damage to hearing during a long operating time without ear protection.
Emission of harmful dusts during operation without an exhaustion plant.
Danger of injury through the saw blade tooth when replacing saw blades.
7. Safety notes
The machine may only be operated and attended by people who are familiar with it and well
informed about the dangers. Repairs may only be made by qualified staff.
The machine must be operated in line with all appropriate regulations for prevention of
accidents as well as with the generally accepted requirements about safety and industrial
medicine.
No warranty is given by the manufacturer for any damage resulting from unauthorized
changes on the machine.
Improper use of high-speed machines can be dangerous! Therefore:
Read the instructions for use carefully before operating the machine.
Never work without the protective equipment as specified for each operation and do not
change anything in the machine that could be detrimental to its safety.
Children and young people are not allowed to operate the machine, except for young
people under supervision of an expert for training purposes.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Graule ZS 135 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Graule ZS 135 in de taal/talen: Engels als bijlage per email.

De handleiding is 0.85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info