3.
Sealing with sealing glass and sealing screw (A)
as accessories – IP 40
Attach the sealing glass, article number 46.13.0002.4, and secure it
with the sealing screw, article number 16.10.0011.8.
4. Operating the time switches
The steps marked with the symbol are necessary to carry out a switching
program.
4.1 Reset
Press the "Reset" key with a pencil or similar
object. This sets the time switch to its basic setting.
– before every restart
– to delete all switching times and the time
4.2 Entering the time and current day of the week
After pressing the "Res" key (see 4.1):
During the summer time period: press the "±1h" key once.
Keep the " " key pressed during steps
,
and
.
With the "h" key: enter the hours
With the "m" key: enter the minutes
With the "Day" key: enter the current day 1= Mo ... 7 = Su
Release the " " key
The colon now flashes at one second intervals.
Note:
If the "h/m" keys are pressed for longer than 2 seconds, the display
will enter fast-forward scroll mode.
or
Save with the " " key.
The time switch goes over to automatic mode and displays
the current time.
Begin every additional switching time and the associated
switching state = ON or = OFF again with 4.3.
Note:
If an input is incomplete, the segments still not selected
are displayed flashing.
Refer to the unit imprint/circuit diagram for connection details.
The following appears after approximately 2 seconds:
Summer time and
winter time
changeover
Hand switch
channel 1
Reset
Enter
hours
Days of the
week flash
Enter
minutes
Holiday
program
Enter
time
Enter
switching
time
Hand switch
channel 2
Deselect days
of the week
Select days
of the week
A
5. Additional functions
5.1 Summer time and winter time setting
● Press the "±1h" key once.
5.2Automatic summer time/winter time changeover
The following 3 changeover variants are available:
4.4 Free channel block formation
The channels 1 and
2 or 1 or 2 can be assigned as required to
every switching command " " or " ".
If you have deselected a day on which the switching command should
be carried out,
Reading the entered data
Press the keys "±1h" and "Day" once simultaneously.
Pressing the key "±1h" several times allows all entered data to be read
in turn
The key " " allows you to return to the current operating state at
any time.
Changing the entered data
Changes can only be carried out in the variants cHA and HA.
Press the keys "±1h" and "Day" once simultaneously
Press the key "±1h" twice
Select the variant cHA or HA with the key "m"
Alter the changeover times as described in Figs. 1 to 5.
Deactivating the automatic S/W changeover function
Press the keys "±1h" and "Day" once simultaneously.
Press the key "h" until "– –" appears (after the last day in the relevant
month)
Press the key " ": The clock changes to the current operating state.
The S/W time changeover can then be performed either manually by
pressing the key "±1h" once or new data can be entered as shown in
Figs. 1 to 5.
5.3 Manual switch " "
The current switching state can be changed at any time with the " " key for
channel 1 or 2 (depending on the version). Use of this manual override facility
does not alter any of the programmed information.
5.7 AM/PM time display
If the "±1" key and the "h" key are pressed simultaneously, the time display
is switched to AM/PM mode (used mainly in English-speaking countries).
5.8 Holiday program
Note:
The holiday program has priority over the standard week program.
The holiday program can only be entered if all seven days of the week
(1234567) are selected.
5.6 Deleting individual switching times
Keep pressing the "Prog." key until the switching time to be deleted is
displayed.
Set to "– –" with the "h" or "m" key and then press the " " key for
about three seconds.
The switching time is deleted and the current time is displayed after the key is
released.
Aborting the holiday program prematurely
If the holiday pr
ogram has already started:
● Press the " " key once
If the holiday pr
ogram has not yet started:
● Press the " " key twice
6. Technical data
Connection see unit imprint
Switching capacity see unit imprint
Ambient temperature –10 °C to +55 °C
Running reserve 150 h at +20 °C
Memory locations 42
Shortest switching time 1 min.
Programmable every minute
Protection IP 20
If the holiday program is to start on a different day to the current one –
max. 6 days ahead – use the "Day" key to select the day on which the
holiday program is to commence.
If the holiday program is to be executed for up to max. 99 days, continue with
steps
+
.
If the holiday program is to be executed for an unlimited period, leave out
step
and continue with step
.
Enter the required number of holiday days with the "Sel." key
(1 to max. 99 days).
Press the " " key to save the entries.
If the current day of the week was entered as the holiday
program start, the following appears:
d = day
number of
entered
holiday days
Image II
Operating Instructions MIL 72/2 digi 42
WA-EKF 3054/01.96/S:MMS/D:Str./80.10.0739.7
1. Putting into operation
Electrical units may only be installed and assembled by a skilled electrician. (The
term "skilled electrician" is defined in VDE 0105).
Notes:
The unit contains well-designed electronic components which are largely protected
against external interference. However, it must be remembered that extremely high
interference voltage peaks can be superimposed on the mains voltage, depending
on the installation site. Interference which, despite all internal protective measures,
can also effect an electronic unit also arises when contactors are switched. In order
to guarantee the greatest possible operational reliability, the following details must
be observed:
a) In the case of larger systems, a suitable varistor or RC element
must be used to provide interference suppression for contactor
coils directly switched by the time switch.
b) If inductive direct current loads are switched, a suppressor diode
must be installed.
c) Inductive loads and particularly fluorescent lamps place particular
demands on the output contacts. In each individual case, check
whether it is appropriate to install an isolating relay or contactor.
2. Assembly and connection
Fit the base in accordance with local conditions.
GB
4.3 Entering the switching times
42 memory locations are available
Each switching time occupies 1 memory location.
Keep pressing the "Prog." key until a free memory location
"– – : – –" is shown in the display..
Select the switching functions " " (ON) or " " (OFF) with the
" " key for channel 1 or 2 (depending on the version).
With the
"h"
key: enter the hours
With the
"m"
key: enter the minutes
If a switching command is to be executed every day, proceed with
step
. If 1 switching command is to be executed only on one day or
on certain days skip step
and continue with step
.
Reselect the deselected day with the "Day" key (day of the week and
cursor flash).
Confirm this day with "Sel." (cursor flashes).
Press the "Day" key (day is reselected).
Save with the "Prog." key
(the next free memory location is displayed)
or
Save with the " " key.
AU (Automatic) = fixed changeover
The S/W time changeover is performed on the basis of a predefined
calendar program which is permanently programmed up until the year 2079
and cannot be changed.
(Statutory summer time ruling of the European Union and Switzerland).
Start of summer time: Always the last Saturday in March.
The hour is advanced by one hour from 2 to 3.
End of summer time: Always the last Saturday in October.
The hour is moved back by one hour from 3 to 2.
cHA (calculated semi-automatic) =
freely selectable changeover with weekday reference
You enter the valid summer time starting date for your country (e.g. date of
the last Friday in April of the current calendar year) and also the date on
which summer time ends (e.g. date of the first Tuesday in October of the
current calendar year).
The program automatically assigns to this date the correct day of the week
(in this case Friday and Tuesday).
In the subsequent years, the time changeover always takes place on the
calculated day of the week, irrespective of the date (in this case the last Friday
in April and the last Tuesday in October).
HA (semi-automatic) =
freely selectable changeover with date reference
You enter the valid summer time starting and end dates for your country.
In the subsequent years, the time changeover always takes place on the same date.
Activation of the automatic summer time/winter time
changeover function
A requirement for the automatic S/W time changeover is that the current date
is entered.
If the time switch is set to AM/PM, the month is set with the key "h" and the
date is set with the key "m".
Entering the current date
Press the keys "±1h" and "➜Day" once simultaneously.
Display
– with key "h"
enter the current date, e.g. 09
– with key "m"
enter the current month, e.g. 02
Display
– enter the current year with
the "m" key
– select the required variant with
the key "m"
Display
activate
AU (Automatic)
with the key " "
The time switch changes
to the current operating state
Display
Press "±1h" once
– enter the summer time starting date
with "h" and "m"
(e.g. 28:04)
Display
Press the key " "
– enter the end of summer time with
"h" and "m" (e.g. 26:09)
The time switch changes to the current operating state
Press the key "±1h" once
(only if mode cHA or HA is required)
Display
flashing
Press "±1h" once
Press "±1h" once
Save with the "Prog." key or
With the "Day" key, select 1 day on which the switching command
is not
to be carried out (cursor flashes)
Confirm this day with the "Sel." key (day of the week and cursor flash)
Press the "Day" key (day is deselected).
Repeat steps
,
and
for every day to be deselected
Save with the "Prog." key (the next free memory location is
displayed)
Automatic Mode Manual Mode
Continuous Operation
= ON
= OFF
= OFF
= ON
= Continuous ON
= Continuous OFF
The switching times If the current switching You can only return
correspond to the
state is changed manually,
to automatic mode
entered program. the next switching from the and
command is again switching modes
executed automatically by pressing the
according to the entered " " key.
switching program.
5.4 Reading the programmed switching times
Press the "Prog." key several times:
– displays all entered switching times starting with the first memory
location.
– the first free memory location "– – : – –" is then displayed.
– the number of memory locations still free is then displayed
If the memory locations are occupied, the following appears in the display: "FR "
Press the " " key:
The time switch changes to automatic mode and displays the current time.
5.5Changing the programmed switching times
Keep pressing the "Prog." key until the switching time to be changed is
displayed
The new data can then be entered as described in Point 4.3.
Note on saving switching times:
If programming is not
completed with the " " key after the switching
time is entered (4.3), the complete switching command is still auto-
matically saved after approximately 90 seconds. The time switch then
changes to automatic mode and shows the current time again
Enter switching times for the holiday period as described
under 4.3. Whilst programming, the " " key must be
pressed to denote a holiday instruction.
The " " key must be pressed for each switching time.
Next, save the holiday switching times with the "Prog." or " " key.
Entering the start and duration of the holiday program
After entering the switching times for the holiday program
Press the " " key once. the following image appears:
Cursor of
the current
day of the
week flas-
hes
Ho = Holiday
Image I
Image II remains until the holiday days have passed, for example
d:10, d:09, d:08 .......... etc.
Pressing the " " key again and holding it down now allows the day of the
week, the time and the cur
rent switching state – " " = ON or " " = OFF –
to be checked.
If a day of the week other than the current day was entered as the holiday
program start, the current time is displayed after the " " key is pressed.
The holiday program is then started at midnight at the start of the selected
day of the week and its duration is displayed (Figure II)
After the programmed holiday days have expired, the current time appears in
the display.
