786710
33
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
EN
DETAILED
INSTRUCTIONS
FOR USE OF WASHING
MACHINE
www.gorenje.com
679870en.indd 1679870en.indd 1 25. 02. 2021 09:42:2525. 02. 2021 09:42:25
Life is complicated today. Let's make laundry care simple! Your
new WaveActive washing machine uses innovative technology
and latest achievements in laundry care to help you simplify
your daily household chores. WaveActive technology offers
the gentlest care for any garment, with minimum creasing.
At the same time, your washing machine will be easy on the
environment, owing to its highly efficient use of power, water and
detergent.
This washing machine is intended solely for household use.
Please do not use it for any laundry labelled as not suitable for
machine washing.
The following symbols are used throughout the manual and they have the following meanings:
Information, advice, tip, or recommendation
Warning – general danger
Warning – danger of electric shock
Warning – danger of hot surface
Warning – danger of fire
It is important that you carefully read the instructions.
679870en.indd 2679870en.indd 2 25. 02. 2021 09:42:3725. 02. 2021 09:42:37
679870
3
4 SAFETY PRECAUTIONS
10 WASHING MACHINE DESCRIPTION
11 Technical specifications
12 Control unit
14 INSTALLATION AND CONNECTION
14 Removing the blocking rods
15 Moving and transport after installation
16 Selecting the room
16 Adjusting the washing machine feet
17 Washing machine placement
19 Connecting to water supply
21 Aqua - stop
21 Total aqua - stop
22 Connecting and securing the water discharge hose
24 Connecting the appliance to the power mains
25 BEFORE USING THE APPLIANCE FOR THE FIRST TIME
26 WASHING PROCESS, STEP BY STEP (1–7)
26 Step 1: Heed the labels on the laundry
27 Step 2: Preparing the washing process
30 Step 3: Choosing the washing programme
34 Step 4: Choosing the settings
40 Step 5: Selecting additional functions
44 Step 6: Starting the washing programme
45 Step 7: Change of washing programme or manual (physical) cancellation
46 Step 8: End of the washing programme
47 INTERRUPTIONS AND CHANGING THE PROGRAMME
51 MAINTENANCE & CLEANING
51 Cleaning the dispenser tray
52 Cleaning the water supply hose, detergent dispenser housing, and rubber
door gasket
53 Cleaning the pump filter
54 Cleaning the washing machine exterior
55 TROUBLESHOOTING
55 What to do ...?
56 Troubleshooting and error table
60 Servicing
61 RECOMMENDATIONS FOR WASHING AND ECONOMIC USE YOUR
WASHING MACHINE
65 Stain removal tips
67 DISPOSAL
68 PROGRAM DURATION AND SPINNING RATE TABLE
STEPS OF
THE WASHING
PROCESS
WASHING
MACHINE
CLEANING AND
MAINTENANCE
INTRODUCTION
TROUBLE-
SHOOTING
PREPARING
THE WASHING
MACHINE
BEFORE FIRST
USE
MISCELLANE-
OUS
CONTENTS
679870en.indd 3679870en.indd 3 25. 02. 2021 09:42:4225. 02. 2021 09:42:42
679870
4
Carefully read the instructions for use before using the
washing machine.
Please, do not use the washing machine without reading
and understanding these instructions or use first.
These instructions for use of a washing machine are
supplied with different types or models of washing
machines. Therefore, they may include descriptions
of settings or equipment that are not available in your
washing machine.
Failure to observe the instructions for use or inappropriate
use of the washing machine may result in damage to the
laundry or the appliance, or injury to the user. Keep the
instruction manual handy, near the washing machine.
Instructions for use are available on our website at
www.gorenje.com.
Your washing machine is intended solely for household
use. If the washing machine is used for professional,
for-profit purpose or purpose exceeding normal use in a
household, or if the washing machine is used by a person
who is not a consumer, the warranty period shall be equal to
the shortest warranty period required by relevant legislation.
SAFETY PRECAUTIONS
679870en.indd 4679870en.indd 4 25. 02. 2021 09:42:4225. 02. 2021 09:42:42
679870
5
Follow the instructions for correct installation of the Gorenje
washing machine and connection to the water and power
mains (see chapter »INSTALLATION AND CONNECTION«).
Connection to water and power supply has to be executed
by an adequately trained technician or expert.
Any repair and maintenance pertaining to safety or
performance should be done by trained experts.
To avoid danger, a damaged power cord may only be
replaced by the manufacturer, a service technician, or an
authorized person.
Before connecting the washing machine to the power
mains, wait for at least 2 hours until it reaches room
temperature.
In case of a defect, only use approved spare parts by
authorized manufacturers.
In case of incorrect washing machine connection, incorrect
use, or servicing by an unauthorized person, the user shall
bear the cost of any damage as such damage shall not be
covered by warranty.
The washing machine may not be connected to the power
mains using an extension cord.
Do not connect the washing machine to power mains using
an external switching device such as a programme timer, or
connect it to power mains that is regularly switched on and
off by the power supply provider.
679870en.indd 5679870en.indd 5 25. 02. 2021 09:42:4225. 02. 2021 09:42:42
679870
6
Do not connect the washing machine to an electrical outlet
intended for an electric shaver or hair dryer.
Do not install the washing machine in a room where the
temperature can drop to below 5°C, as washing machine
parts may be damaged in case of water freezing.
Place the washing machine on a level and stable solid
(concrete) base.
If the washing machine is placed on an elevated stable base,
the washing machine has to be additionally secured against
tipping.
Before the first use of the washing machine, remove the
blocking rods, as switching on a blocked washing machine
can result in serious damage (see chapter »INSTALLATION
AND CONNECTION/Removing the blocking rods«). Warranty
shall be void in cases of such damage.
To connect the washing machine to water supply, make
sure to use the supplied water supply hose and gaskets.
Water pressure has to be between 0.05 and 0.8 MPa (0.5 – 8
bar).
Always use a new water supply hose to connect the washing
machine to water supply; do not reuse an old water supply
hose.
The end of the water discharge hose should reach into a
water drain line.
Before the start of the washing cycle, press the door on the
679870en.indd 6679870en.indd 6 25. 02. 2021 09:42:4225. 02. 2021 09:42:42
679870
7
indicated spot until it locks into place. The door cannot be
opened during washing machine operation.
We recommend removing any impurities from the
washing machine drum before the first wash using the
Cotton 90°C programme (see PROGRAMME TABLE).
After the washing cycle, close the water tap and pull out
the washing machine plug from the power socket.
Clean the pump filter whenever the symbol appears on the
display unit.
Only use the washing machine for washing laundry, as
described in the instruction manual. The machine is not
intended for dry cleaning.
Only use agents for machine washing and care of
laundry. We shall not be responsible for any damages or
discolouration of gaskets and plastic parts resulting from
incorrect use of bleaching or colouring agents.
When descaling, only use descaling agents with added
anti-corrosion protection. (Only use non-corrosive descaling
agents.) Follow the manufacturer's instructions. Finish the
descaling process with several rinse cycles or by running the
Steril tub (Self-cleaning programme) in order to remove any
residual acid (e.g. vinegar etc.).
Do not use detergents that contain solvents as this could
lead to release of poisonous gases, damage to the washing
machine, and risk of fire and explosion.
679870en.indd 7679870en.indd 7 25. 02. 2021 09:42:4225. 02. 2021 09:42:42
679870
8
No silver ions are released during the washing programme.
The washing machine is not intended for use by persons
(including children) with physical or mental impairments,
or persons with lacking experience and knowledge. These
persons should be instructed about the use of the washing
machine by a person responsible for their safety.
The warranty does not cover consumables, minor
deviations in colour, increased noise that results from
appliance age and which does not affect the functionality of
the appliance, and aesthetic defects on components, which
do not affect the functionality and safety of the appliance.
CHILD SAFETY
Before closing the washing machine door and running the
programme, make sure there is nothing except laundry in the
drum (e.g. if a child climbed into the washing machine drum
and closed the door from the inside).
Keep the detergent and conditioner out of reach of children.
Activate the child lock. See chapter »CHOOSING THE
SETTINGS/Child lock«.
Do not let children younger than three years come
near the appliance, unless they are under constant
supervision.
The washing machine is made in compliance with all
relevant safety standards.
This washing machine may be used by children aged 8
years and above and by persons with reduced physical,
679870en.indd 8679870en.indd 8 25. 02. 2021 09:42:4325. 02. 2021 09:42:43
679870
9
sensory or mental capabilities or lack of experience and
knowledge, but only if they are supervised during the use of
the washing machine, if they have been provided relevant
instructions regarding safe use of the washing machine, and
if they understand the hazards of inappropriate use. Make
sure children do not play with the appliance. Children may
not clean the washing machine or perform any maintenance
tasks without supervision.
DANGER OF HOT SURFACE
At higher washing temperatures, the door glass will heat up.
Be careful to avoid burns. Make sure children do not play
near the door glass.
WATER OVERFLOW PROTECTION (WITH WASHING
MACHINE SWITCHED ON)
If the water level in the appliance rises above normal level,
then the excess water level protection will be activated. It will
shut off the water supply and start pumping out the water.
The program is interrupted and an error is reported (see
TROUBLESHOOTING TABLE).
TRANSPORT/TRANSPORT AFTER INSTALLATION
If you intend to move the washing machine after it has
been installed, then it should be blocked by inserting at
least one blocking rod (see chapter »INSTALLATION AND
CONNECTION/Moving and transport«). Before inserting the
blocking rods, disconnect the washing machine from the
power mains!
679870en.indd 9679870en.indd 9 25. 02. 2021 09:42:4325. 02. 2021 09:42:43
679870
10
BACK
1 Water supply hose
2 Power cord
3 Water discharge hose
4 Adjustable feet
FRONT
1 Control unit
2 Start/pause button
3 Programme selector knob
4 On/off/reset button
5 Dispenser tray
6 Door
7 Rating plate
8 Pump filter
34 25
6 87
1
2
1
3
4
WASHING MACHINE DESCRIPTION
679870en.indd 10679870en.indd 10 25. 02. 2021 09:42:4425. 02. 2021 09:42:44
679870
11
TYPE: PS15/XXXXX MODEL: XXXXXX.X
Art.No.: XXXXXX Ser.No.: XXXXXXXX
220-240 V ~ XX Hz XX A Pmax.: XXXX W
XXXX W XXXX/min X kg 0,05-0,8 MPa
IPX4
MADE IN SLOVENIA
Rating plate
TECHNICAL SPECIFICATIONS
(DEPENDING ON THE MODEL)
Rating plate with basic information about the washing machine is fitted on the front wall of the
washing machine door opening (see chapter »WASHING MACHINE DESCRIPTION«).
Maximum load See rating plate
Width 600 mm 600 mm 600 mm 600 mm
Height 850 mm 850 mm 850 mm 850 mm
Washing machine depth (a) 430 mm 465 mm 545 mm 610 mm
Depth with door closed 462 mm 495 mm 577 mm 640 mm
Depth with door open (b) 947 mm 980 mm 1062 mm 1125 mm
Washing machine weight X kg (depending on the model)
Rated Voltage See rating plate
Nominal power See rating plate
Connection See rating plate
Water pressure See rating plate
Current See rating plate
Frequency See rating plate
679870en.indd 11679870en.indd 11 25. 02. 2021 09:42:4625. 02. 2021 09:42:46
679870
12
3START/PAUSE BUTTON
Use this button to start or
pause a programme.
Upon start-up or during pause,
the button backlight will flash;
when the programme is started
and in progress, it will be lit
continuously.
1ON/OFF/RESET
BUTTON
Use this button to turn the
washing machine on and
off, and to reset the washing
programme.
The button is lit when the
washing machine is switched
on.
2PROGRAMME
SELECTOR KNOB
2a Light next to the selected
washing programme is lit.
CONTROL UNIT
1 2 2a 3
679870en.indd 12679870en.indd 12 25. 02. 2021 09:42:4625. 02. 2021 09:42:46
679870
13
4
WASHING MODE
4a POWERCARE
4b TIMECARE
5DOSEAID
Information on
recommended amount of
powder and liquid detergent,
according to the selected
settings and the amount of
laundry in the drum.
6GREENGUIDE
Information on water and
power consumption, according
to the selected washing
settings.
7PREWASH
8CLEAN THE PUMP
FILTER symbol lighting
9 TEMP. (WASHING
TEMPERATURE)
Temperature settings options
10
SPIN (SPINNING RATE
/DRAIN /PUMP
STOP )
Option to set the spinning rate
11START DELAY
Option to set a start
delay
12
CHILD LOCK symbol
lighting
Press the positions 11+13 and
hold them for 3 seconds.
13 W ATER+ (HIGH
WATER LEVEL)
Option to set the higher water
level (2 levels)
7 98 10 11 1312
654b4a4
679870en.indd 13679870en.indd 13 25. 02. 2021 09:42:4825. 02. 2021 09:42:48
679870
14
1Move the hoses
and undo the
screws on the back of
the washing machine.
Remove the two
angular pieces.
2Slide the angular
pieces onto the
grove in the blocking
rod; before doing so,
rotate the right angular
piece to the opposite
side.
3Use the angular
pieces to rotate
the blocking rods by
90°and pull them out.
4Cover the two
holes through
which the blocking
rods were inserted
with plastic plugs, and
redo the screws that
you undid in step 1.
The plastic plugs are
supplied in the bag with
the washing machine
instruction manual.
INSTALLATION AND CONNECTION
Remove all packaging. When removing the packaging, make sure not to damage the appliance
with a sharp object.
REMOVING THE BLOCKING RODS
Before the first use of the appliance, transport rods must be removed. A blocked washing
machine may be damaged when it is switched on for the first time. Warranty shall be void in
cases of such damage!
679870en.indd 14679870en.indd 14 25. 02. 2021 09:42:5525. 02. 2021 09:42:55
679870
15
MOVING AND TRANSPORT AFTER INSTALLATION
If you wish to move the washing machine after it has been installed, the angular pieces and at
least one blocking rods have to be re-installed to prevent vibration damage to the washing machine
during transport (see chapter »INSTALLATION AND CONNECTION/Removing the blocking rods«). If
you lost the angular pieces and the blocking rods, they can be ordered from the manufacturer.
After transport, the washing machine should be left to stand still for at least two hours
before it is connected to the power mains, so that it can reach room temperature. The
appliance should be installed and connected by a trained technician.
Carefully read the instructions for use before connecting the washing machine. Repair or
any warranty claim resulting from incorrect connection or use of the washing machine shall
not be covered by the warranty.
679870en.indd 15679870en.indd 15 25. 02. 2021 09:42:5725. 02. 2021 09:42:57
679870
16
Incorrect levelling of the washing machine with the adjustable legs may cause vibration,
appliance sliding across the room, and loud operation. Incorrect levelling of the washing machine is
not subject to warranty.
Sometimes, unusual or louder noise may appear during appliance operation; these are mostly
the result of improper installation.
1Level the washing
machine in
longitudinal and
traverse direction by
rotating the adjustable
feet.
2After adjusting
the height of the
feet, firmly tighten the
jam nuts (counter nuts)
using a spanner No
17, by turning them
towards the bottom of
the washing machine
(see figure).
SELECTING THE ROOM
Floor on which the washing machine is placed must have a concrete base. It should be clean
and dry; otherwise, the washing machine may slide. Also, clean the bottom surface of adjustable
feet.
The washing machine must stand level and stable on a solid base.
ADJUSTING THE WASHING MACHINE FEET
Use a water scale and spanner No. 32 (for feet) and 17 (for the nut).
679870en.indd 16679870en.indd 16 25. 02. 2021 09:42:5825. 02. 2021 09:42:58
679870
17
WASHING MACHINE PLACEMENT
If you also have a Gorenje dryer of corresponding (same) dimensions, it can be placed on top of the
Gorenje washing machine (in this case, vacuum feet must be used) or next to it (figures 1 and 3).
If your Gorenje washing machine is smaller (minimum depth 545 mm) than your Gorenje dryer, then
the dryer support has to be purchased (figure 2). It is essential to use the vacuum feet! Additional
equipment (dryer support (a) and vacuum feet (b)) are available for purchase at service units.
The surface on which the appliance is placed should be clean and level.
Gorenje washing machine onto which you intend to place the Gorenje dryer should hold the weight
of the Gorenje dryer (see chapter »WASHING MACHINE DESCRIPTION/Technical information«).
12 3
4X
b
a
679870en.indd 17679870en.indd 17 25. 02. 2021 09:43:0125. 02. 2021 09:43:01
679870
18
Before connecting the washing machine to the power mains, wait for at least 2 hours until
it reaches room temperature.
Opening the washing machine door (bird's-eye view)
See chapter »WASHING MACHINE
DESCRIPTION/Technical information«).
a = Washing machine depth
b = Depth with door open
The washing machine may not be in contact with a wall or adjacent furniture. For optimum
washing machine operation, we recommend observing the clearances from the walls as indicated in
the figure.
In case of failure to observe the minimum required clearances, safe and correct washing machine
operation cannot be ensured. Moreover, overheating can also occur (figures 1 and 2).
Installing the washing machine under a countertop is not recommended.
Washing machine installation clearances
50 mm
2
b
a
180°
3
25 mm
25 mm
1
679870en.indd 18679870en.indd 18 25. 02. 2021 09:43:0325. 02. 2021 09:43:03
679870
19
If your washing machine features a hot and cold water connection, but you only wish to connect
it to cold water supply, do not install the hot water hose and close the hot water connection on the
back of the washing machine with the supplied cap.
If your washing machine features hot and cold water connection with full aquastop (option
B), and you only wish to connect it to the cold water supply, then seal the hot water hose with a
suitable 3/4" plug that is not supplied with the appliance. The 3/4" plug is available in specialized
plumbing supplies stores.
For normal washing machine operation, the pressure in the water mains should be between 0.05
and 0.8 MPa (0,5 - 8 bar). Minimum dynamic water pressure can be determined by measuring the
water flow. In 15 seconds, 3 litres of water should flow from a fully open tap.
AAQUA - STOP
BTOTAL AQUA -
STOP
CREGULAR
CONNECTION
CONNECTING TO WATER SUPPLY
Attach the hose to the water tap by screwing it onto the thread.
A
B
C
679870en.indd 19679870en.indd 19 25. 02. 2021 09:43:0625. 02. 2021 09:43:06
679870
20
If your model has connections for both hot and cold water, then connect one hose to the
cold water supply (blue wing nut or blue mark on the hose) and the other one to the hot water
supply (red wing nut or red mark on the hose), as indicated on the back of the washing machine.
Connections are labelled with letters C and H (C = cold, H = hot). Warm water (mixture of hot and
cold water) is only added for programmes at 40°C or higher.
Tighten the water supply hose by hand, firmly enough for the hose to have a good seal (max. 2 Nm).
After connecting the hose, the seal must be checked for any leaks. Do not use pliers or similar tools
when connecting the hose as this could damage the nut thread.
Only use the water supply hose supplied with the appliance. Do not use any used or other hoses.
679870en.indd 20679870en.indd 20 25. 02. 2021 09:43:0725. 02. 2021 09:43:07
679870
21
Do not dip the water supply hose with the AQUA - STOP system in water as it contains an
electric valve.
When connecting the water supply hose, make sure to connect it in a way that allows adequate
and unobstructed water supply.
a
AQUA - STOP
If an internal tube or hose is damaged, a shut-off system is activated that cuts the water supply
to the washing machine. In such case, the control glass (a) will turn red. Replace the water supply
hose.
TOTAL AQUA - STOP
If an internal tube or hose is damaged and if water is present on the bottom of the washing
machine, a shut-off system is activated that cuts the water supply to the washing machine. In this
case, the washing process will be stopped, water supply will be cut off, and the washing machine
will switch on the pump and signal an error.
(ONLY WITH SOME MODELS)
(ONLY WITH SOME MODELS)
679870en.indd 21679870en.indd 21 25. 02. 2021 09:43:0825. 02. 2021 09:43:08
679870
22
ADischarge
hose end may
be placed over a
washbasin or a
bathtub. B Use a
string fed through the
opening in the elbow
support to attach the
hose and prevent it
from slipping to the
floor.
BDischarge hose
may also be
attached directly to the
washbasin drain.
CDischarge hose
can also be
attached to a wall
drain with a trap;
such trap should be
properly installed to
allow cleaning.
CONNECTING AND SECURING THE WATER DISCHARGE
HOSE
Feed the water discharge hose into a washbasin or a bathtub, or connect it directly to a drain
(discharge hose minimum diameter 4 cm). The vertical distance from the floor to the end of the
discharge hose may be no more than 100 cm and no less than 60 cm. It can be attached in three
ways (A, B, C).
A
B
C
max 100 cm
min 60 cm
max 90 cm
max 100 cm
max 150 cm
A
B
C
max 100 cm
min 60 cm
max 30 - 40 cm
max 160 cm
max 90 cm
679870en.indd 22679870en.indd 22 25. 02. 2021 09:43:1025. 02. 2021 09:43:10
679870
23
If the discharge hose is not correctly attached, safe and correct washing machine operation
cannot be ensured.
DThe discharge
hose has to be
attached and affixed to
the pin on the back of
the washing machine,
as shown in the figure.
679870en.indd 23679870en.indd 23 25. 02. 2021 09:43:1225. 02. 2021 09:43:12
679870
24
Before connecting the washing machine to the power mains, wait for at least 2 hours until
it reaches room temperature.
Connect the washing machine to a grounded power outlet. After installation, the wall outlet should
be freely accessible. The outlet should be fitted with an earth contact (in compliance with the
relevant regulations).
Information on your washing machine is indicated on the rating plate (see chapter »WASHING
MACHINE DESCRIPTION/Technical information«).
We recommend using over-voltage protection to protect the appliance in case of a
lightning strike.
The washing machine may not be connected to the power mains using an extension cord.
Do not connect the washing machine to an electrical outlet intended for an electric shaver or hair
dryer.
Any repair and maintenance pertaining to safety or performance should be done by trained
experts.
A damaged power cord may only be replaced by a person authorized by the manufacturer.
2 h
CONNECTING THE APPLIANCE TO THE POWER MAINS
679870en.indd 24679870en.indd 24 25. 02. 2021 09:43:1325. 02. 2021 09:43:13
679870
25
Do not use any solvents or cleaning agents that could damage the washing machine (please
observe the recommendations and warnings provided by the cleaning agent manufacturers).
BEFORE USING THE APPLIANCE
FOR THE FIRST TIME
Make sure the washing machine is disconnected from the power mains; then, open the door
towards you (figures 1 and 2).
Before first use, clean the washing machine drum with a soft moist cotton cloth and water, or use
the Cotton 90°C programme. There should be no laundry in the washing machine drum; the drum
should be empty (figures 3 and 4).
12
34
679870en.indd 25679870en.indd 25 25. 02. 2021 09:43:1525. 02. 2021 09:43:15
679870
26
WASHING PROCESS, STEP BY STEP
(1–7)
STEP 1: HEED THE LABELS ON THE LAUNDRY
Normal wash;
Sensitive laundry
Max.
washing
temp.
95°C
95
95
Max.
washing
temp.
60°C
60
60
Max.
washing
temp.
40°C
40
40
Max.
washing
temp.
30°C
30
30
Hand wash
only
Do not
wash
Bleaching Bleaching in cool water
c1
Bleaching not allowed
Dry cleaning Dry cleaning
with all agents
A
Petroleum
solvent R11,
R113
P
Dry cleaning in
kerosene, pure
alcohol, and
R113
F
Dry cleaning not
allowed
Ironing Hot ironing,
max.
200°C
Hot ironing,
max.
150°C
Hot ironing, max.
110°C
Ironing not
allowed
Drying Dry flat (place on
a flat surface)
Drip dry
Line dry
High temperature
Low temperature
Do not tumble
dry
679870en.indd 26679870en.indd 26 25. 02. 2021 09:43:1725. 02. 2021 09:43:17
679870
27
STEP 2: PREPARING THE WASHING PROCESS
1. Sort the laundry by type of fabric, colour, soiling, and allowed washing temperature (see
PROGRAMME TABLE).
2. Wash the laundry that sheds a lot of fibre or lint separately from other laundry.
3. Close the buttons and zippers, tie any ribbons, and turn the pockets inside out; remove any
metal clips that could damage the laundry and washing machine interior, or clog the drain.
4. Place very sensitive clothes and small items in a special-purpose laundry washing bag.
(The special purpose laundry bag is available as an optional accessory.)
679870en.indd 27679870en.indd 27 25. 02. 2021 09:43:3525. 02. 2021 09:43:35
679870
28
SWITCHING ON THE WASHING MACHINE
Use the power cord to connect the washing machine to power mains, and connect the washing
machine to water supply.
Press the (1) ON/OFF/RESET button to switch on the washing machine (figure 1).
With some models, the washing machine drum is also lit for 5 minutes when the washing machine
is switched on (figure 2).
The light in the washing machine drum can also remain lit during appliance operation, if you press
the START/PAUSE (3) key, as well as after the washing programme is completed.
(The lamp in the washing machine drum is not suitable for any other use.)
The lamp in the washing machine drum may only be replaced by the manufacturer, a service
technician or an authorized person.
12
1
679870en.indd 28679870en.indd 28 25. 02. 2021 09:43:3625. 02. 2021 09:43:36
679870
29
LOADING THE WASHING MACHINE
Open the washing machine door by pulling the handle towards you (figure 1).
Insert the laundry into the drum (after making sure the drum is empty) (figure 2).
Make sure that no garment is stuck between the door and the rubber gasket. Close the washing
machine door (figure 3).
Do not overload the drum! See PROGRAMME TABLE and observe your nominal load as indicated
on the rating plate.
If the washing machine drum is too full, the laundry will not be washed as thoroughly.
1 2
3
679870en.indd 29679870en.indd 29 25. 02. 2021 09:43:3825. 02. 2021 09:43:38
679870
30
2
During operation, the programme selector knob (2) will not rotate automatically.
Washing programmes are comprehensive programmes that include all washing stages, including
softening and spinning (this does not apply to Partial programmes).
Partial programmes are independent programmes. Use them when you feel you do not need the
entire washing programme.
STEP 3: CHOOSING THE WASHING PROGRAMME
Choose the programme by rotating the programme selector knob (2) to the left or to the right
(depending on the type of laundry and how heavily soiled it is). See PROGRAMME TABLE.
When you select the washing programme, the light (2a) on the display unit next to the selected
washing programme lights up.
2a
2
679870en.indd 30679870en.indd 30 25. 02. 2021 09:43:3925. 02. 2021 09:43:39
679870
31
PROGRAMME TABLE
Programme Max. load Programme description
Cotton black
30°C - 40°C
** (1/2) This programme is used for washing dark laundry using
special-purpose detergents for black laundry. The
programme washes at low temperatures, with gentle
tumbling and lower spinning rate.
Cotton color
--; - 60°C
* MAX Programme for lightly to moderately dirty laundry. The
temperature can be set separately; therefore, observe the
instructions indicated on the clothing. Wash the clothes
worn directly on the skin at 60°C. Less heavily soiled
laundry will be thoroughly cleaned at 40°C. Spinning speed
can also be freely selected. Programme duration and
amount of water will be adjusted to the amount of laundry.
Cotton white
40°C - 90°C
* MAX Programme for normally or heavily soiled laundry, white
or coloured. The temperature can be set separately;
therefore, observe the instructions indicated on the
clothing worn directly on the skin. Choose 40°C if the
laundry is only lightly dirty. Spinning speed can be set to
your preference. Programme duration and amount of water
will be adjusted to the amount of laundry.
Mix
(Mixed laundry/
Synthetics)
--; - 60°C
3,5 kg Washing programme for delicate clothing made of
synthetic and mixed fibres or viscose, and for simple
care of cotton. Observe the instructions indicated on the
clothing. Most garments made of synthetic fibres are
washed at 40°C.
Wool/Handwash
--; - 40°C
2 kg Gentle washing programme for washing wool, silk,
and clothes that require manual washing. Maximum
temperature is 40°C. This programme has a short spinning
cycle. Top spinning speed available is 800 rpm.
Speed 20´
30°C
2,5 kg Quick washing programme for laundry that only needs
refreshing.
Power 59´
40°C
** (1/2) Programme for smaller amounts of lightly soiled laundry.
The programme washes with gentle tumbling and lower
spinning rate.
* Maximum load (MAX)
** Half load (1/2)
/ Any load (0 kg – MAX kg)
-- Cold wash
679870en.indd 31679870en.indd 31 25. 02. 2021 09:43:4225. 02. 2021 09:43:42
679870
32
Programme Max. load Programme description
Steril tub
(Self-cleaning
programme)
0 kg Washing programme is used to clean the drum and to
remove detergent residues and bacteria. To select the
programme, rotate the programme selector knob to the left
or to the right to the Steril tub (Self-cleaning programme)
position . Other extra functions cannot be selected.
The drum has to be empty. You can add some distilled
(spirit) vinegar (approx. 2 dl) or sodium bicarbonate
(1 tablespoon, or 15 g). We recommend running the
programme at least once a month.
Rinse/Softening
(Partial
programme)
/ For softening, starching, or impregnating the washed
laundry. It can also be used as a rinse programme, but
without added softener. It is completed with an additional
rinse.
You can also choose WATER+ (HIGH WATER LEVEL) by
selecting the extra function.
Spin/Drain
(Spinning rate/
Drain)
(Partial
programme)
/ Use the programme when you only wish to spin the
laundry.
If you only wish to pump out the water from the washing
machine, press the SPIN (10) button to select (drain)
Sports
(Sportswear)
30°C - 40°C
3,5 kg Slightly soiled sportswear made of cotton, microfibres and
synthetic fibres, at lower spinning rates and a brief final
spinning cycle.
Eco 40-60 * MAX Washing cycle, which is able to clean normally soiled
cotton laundry declared to be washable at 40°C or 60°C.
Allergy care
40°C - 90°C
** (1/2) Washing programme is used to wash normal to heavily
soiled clothes that require special care, such as clothes
for people with highly sensitive skin or skin allergies. We
recommend turning the garments inside out, as this will
also thoroughly wash out the skin and other residues.
You can also select the option to wash at maximum
temperature and maximum spinning speed.
Auto wash
30°C
* MAX Washing programme automatically adjusts the duration of
the main wash and the number of rinses depending on the
amount of laundry in the machine. Use it for lightly soiled
laundry.
No extra programme settings are possible.
* Maximum load (MAX)
** Half load (1/2)
/ Any load (0 kg – MAX kg)
-- Cold wash
679870en.indd 32679870en.indd 32 25. 02. 2021 09:43:4825. 02. 2021 09:43:48
679870
33
Add powder or liquid detergents according to the manufacturer's instructions, considering the
washing temperature, washing program, how soiled the laundry is, and water hardness.
Maximum amount of laundry in kg (for the cotton programme) is indicated on the rating plate
fitted under the washing machine door (see chapter »WASHING MACHINE DESCRIPTION/
Technical information«).
Maximum or nominal load applies to laundry prepared pursuant to the IEC 60456 standard.
For better washing effect, we recommend loading the drum to 2/3 when using the cotton
programmes.
679870en.indd 33679870en.indd 33 25. 02. 2021 09:43:5525. 02. 2021 09:43:55
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gorenje WA946 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gorenje WA946 in de taal/talen: Engels als bijlage per email.

De handleiding is 13.63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info