728680
20
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
20 EN
Mounting
Very heavy product; hood handling and installation must be carried out by at least two persons.
Before beginning installation:
Check that the product purchased is of a suitable size for the chosen installation area.
Remove the charcoal (*) lter/s if supplied (see also relative paragraph). This/these is/are to be mounted only if you want lo use the
hood in the ltering version.
Check (for transport reasons) that there is no other supplied material inside the hood (e.g. packets with screws (*), guarantees (*), etc.),
eventually removing them and keeping them.
If possible, disconnect and move freestanding or slide-in range from cabinet opening to provide easier access to rear wall/ceiling.
Otherwise put a thick, protective covering over countertop, cooktop or range to protect from damage and debris. Select a at surface
for assembling the unit. Cover that surface with a protective covering and place all canopy hood parts and hardware in it.
In addition check whether near the installation area of the hood (in the area accessible also with the hood mounted) an electric socket
is available and it is possible to connect a fumes discharge device to the outside (only suction version).
Carry out all the masonry work necessary (e.g. installation of an electric socket and/or a hole for the passage of the discharge tube).
Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualied technician must verify suitability
of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood. Do not
tile, grout or silicone this appliance to the wall. Surface mounting only.
OPERATION
Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for
5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking.
IHT953S2XBG
To select the functions of the hood press on the symbol. Function will be activated when symbol will be released.
T1. Standby mode (the control panel off – all functions disabled) / ON (control panel switched on)
Note: After about a minute of inactivity (suction and lights), the hood will automatically switch to standby.
T2. ON/OFF lights
- with the lights on, touch the LED strip SL1 with the ngers towards right or left to increase or decrease the intensity of the light.
Note: the light turns on at the last set intensity before its switching off.
T3. ON/OFF Automatic operation “AdaptTech”.
The hood automatically sets the suction speed (power) 2 to increase if the environmental conditions detected by the hood sensor
require it.
If there are no variations in the environmental conditions, after 10 minutes (if the hood is already in suction speed (power) 1), the hood
turns off.
Note: for a correct use of this function, rst perform the „Setting of the parameters for Automatic Operation” (see corresponding
paragraph).
Note: During automatic operation, if the user acts on the other functions that adjust the speed, auto ventilation function is switched off.
T4. ON/OFF Motor
- with the motor running, touch the led strip SL2 with your ngers towards right or left to increase or decrease the suction speed (pow-
er).
Note: the motor starts running at the last suction speed (power) set before switching off.
T5. ON/OFF Intensive suction speed (power) “POWER BOOST” (timed)
Note: After 5 minutes of operation the hood returns to its previous state.
T6. ON/OFF intensive suction speed (power) “POWER BOOST x 2” (timed)
Note: After 5 minutes of operation, the hood goes back to the previous status.
T7. ON/OFF operation mode „ReFresh”.
Every 50 minutes of inactivity, the suction speed (power 1 is turned on for 10 minutes.
T8. ON/OFF Timer of the suction speed (power).
Note: this function is available for the speeds that can be selected with button T4.
Press once or repeatedly to choose the delayed switch off time that you want to set (10-20-30 minutes)
T9. Indicatorandresetltersaturation
The button lights on automatically with steady light when it is necessary to perform the grease lter maintenance.
The button lights on automatically with ashing light when it is necessary to perform the charcoal lter maintenance.
T1 T2 T3 T4 T5 T6 T7 T8 T9
SL1 SL2
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gorenje IHT943A2XBG bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gorenje IHT943A2XBG in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks als bijlage per email.

De handleiding is 6,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info