656011
8
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
- 32 -
Setting the Transmitter
group’s setting turns to the maximum(1/1) or the minimum(Min.). If the current group
is in the TTL mode, all the other groups which are in the M mode will change their
FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop
increments, until one of the group’s setting turns to the maximum(3) or the minimum(-
3). If the current group is in the -- mode (flash off), the amounts will not change.
4. Short press the <GR> Button again to confirm the setting.
Test Flash
1. Press the <TEST> Trigger Button to see the
whether flash will fire normally or not.
2. Fully press the <TEST> Trigger Button, and
the Status Indicator Lamp turns red and the
flash can be triggered.
3. The settings on the transmitter end will
synchronize to the receiver end at the same
time.
Modeling Lamp Control
Double-click the <CH/OK> Button to power ON/OFF the modeling lamp.
Setting the Transmitter
Automatically Enter Power Saving Mode
1. The flash trigger will go into standby mode after the transmitter enter sleep mode, and
the displays on the LCD panel will disappear.
2. Press any of the button (<TEST> fully pressed/<CH/OK>/<GR>/<MODE>) can wake
up the flash trigger. If the transmitter is attached to the CANON EOS camera, half
press the shutter can also wake up the system.
3. If the transmitter is set to single contact mode( isdisplayed), the system will not
enter power saving mode.
The following table lists the available and unavailable custom functions of this flash.
Note: Some icons will be displayed when setting the relevant custom functions to make users
have a good understanding.
Functions
Synchronization
delay setting
Single contact
mode
Custom
Functions No.
C.Fn-00
C.Fn-01
Settings and Description
OFF
Master flash synchronization delay N*100 us
(synchronization delay icon is displayed.)
OFF
ON (The single contact mode set icon is displayed.)
It is advisable to set the transmitter to single contact
mode when using it to trigger the flash by PC cord or
through camera's single contact.
Setting Signs
00
1~100
--
on
C.Fn: Setting Custom Functions
- 31 -
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Godox X1TS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Godox X1TS in de taal/talen: Engels als bijlage per email.

De handleiding is 1,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info