646573
7
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
GEAppliances.com
10
Ext Tumble/Wrinkle Care
Minimizes wrinkles by adding approximately 60
minutes of no-heat tumbling after clothes are
dry. The beeper will sound every five minutes as a
reminder to remove the clothes.
The estimated time remaining display will show
“0:00”.
The extended tumble time does not get added to
the cycle time on the display.
11
Damp Alert
This option causes the dryer to beep when clothes
have dried to a damp level. Remove items that you
wish to hang dry. The Damp Alert will only beep
when this option is selected, and the dryer will
continue to dry.
Removing clothes and hanging them when they are
damp can reduce the need to iron some items.
Volume
Alerts you that the cycle is complete. The beeper
will continue to sound every minute for the next 5
minutes, until the clothes have been removed. The
clothes should be removed when the beeper goes
off so wrinkles don’t set in.
Press Volume to select low, medium or high volume,
or to turn the beeper off.
To turn on or off the sounds the buttons make
when pressed, press and hold the Volume button
for 3 seconds.
Lock Control
You can lock the controls to prevent any
selections from being made. Or you can lock
or unlock the controls after you have started a
cycle.
Children cannot accidentally start the dryer by
touching buttons with this option selected.
To lock the dryer, press and hold the Lock
Control button for 3 seconds.
To unlock the dryer controls, press and hold the
Lock Control button for 3 seconds.
A sound is made to indicate the lock/unlock
status.
The indicator light above the button will
illuminate when the controls are locked.
NOTE: The Power button can still be used when
the machine is locked.
12
13
14
Clean Filter Message
This message represents only a reminder and does
not always appear when the filter needs cleaning.
The filter should be cleaned after every drying cycle
is complete.
This message will disappear after the Start/
Pause button is pressed. Even though you may
have already cleaned the filter (before or after the
Power button has been pressed), the “Clean Filter
message will still be displayed until the Start/Pause
button is activated.
15
Display
Displays the approximate time remaining until
the end of the cycle.
As the cycle begins, you will see an initial
approximate total cycle time in the display.
Then lights will “race” in the display. This means
the dryer is continuously monitoring the amount
of moisture in the load. The lights will continue
until the dryer senses a low level of moisture in
the load. At that point, the dryer will calculate
and display the approximate time remaining.
My Cycle (on some models)
Set up your favorite combination of settings and
save them here for one touch recall. These custom
settings can be set while a cycle is in progress.
To store a My Cycle combination of settings:
1. Select your drying cycle.
2. Change Temp and Level settings to fit your
needs.
3. Select any drying options you want.
4. Press and hold the My Cycle button for 3
seconds to store your selection. A beep will
sound and the button will light up.
To recall your stored My Cycle combination:
Press the My Cycle button before drying a load.
To change your stored My Cycle combination:
Repeat steps 1–4.
16
My
Cycle
7
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw General Electric GFD45 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van General Electric GFD45 in de taal/talen: Engels, Spaans als bijlage per email.

De handleiding is 3,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info