Handleiding Gecko in.k800 (pagina 3 van 31) (Engels)

764850

Verklein

Vergroot

Pagina terug

1/31

Pagina verder

in.k800

intuitive color keypad

TechBook

Gecko Alliance

450 des Canetons, Québec (Qc), G2E 5W6 Canada, 1.800.78.GECKO

www.geckoalliance.com Printed in Canada

9919-101191-K

Rev. 12-2019

All trademarks or registered trademarks

are the property of their respective owners.

Full color control

On-screen audio control

Water care selection

Warnings �� 2

Introduction �� 3

Overview

-in�k800 dimensions �� 4

Installation

-Installation of in�k800 �� 5

-Drilling template �� 6

-Installation notes �� 7

-Connecting in�k800 keypad to the spa pack �� 7

-Installation errors �� 8

Keypad functions

-in�k800 keypad layout �� 9

-Settings key �� 9

-Mode key �� 9

-Power �� 9

-Main screen �� 9

-Start or stop accessories �� 10

-Notifications �� 10

-Water temperature �� 11

-Settings �� 11

-Water care �� 12

-Water care modes �� 12

-Modifying schedules ��12

-Heat pump �� 13

-Heat pump modes �� 13

-Audio �� 14

-in�clear-200 (linked version) �� 15

-Maintenance �� 15

-Maintenance reminders �� 16

-Standby �� 16

-Date and time �� 17

-Keypad settings �� 17

-Wi-Fi (in�touch only) �� 18

-Miscellaneous �� 19

-Electrical configuration �� 20

-About �� 21

-in�mix functions �� 22

-in�tune functions �� 23

-Connecting the in�tune to the spa pack ��23

-in�stream functions �� 24

-Connecting the in�stream to the spa pack �� 24

-in�stream 2 functions �� 25

-Connecting the in�stream 2 to the spa pack �� 25

-in�clear functions �� 26

Error messages �� 27

Feature matrix �� 28

Specifications �� 29

Table of contents

WARNINGS

Before installing or connecting the unit, please read the following�

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS MAY SIGNIFICANTLY SHORTEN THE PRODUCT’S LIFE

TIME, AND LEAD TO FAILURES AS WELL AS HAZARDOUS CONDITIONS*. COMMON SENSE MUST ALWAYS PREVAIL

WHEN EVALUATING THE INSTALLATION AND/OR USE OF ANY ELECTRONIC CONTROL IN A FINAL APPLICATION.

• RESPECT ENVIRONMENTAL CONDITIONS LISTED AT END OF TECHBOOK�

• THIS UNIT MUST BE INSTALLED BY QUALIFIED PERSONNEL�

• ONLY QUALIFIED PERSONNEL ARE TO SERVICE THIS UNIT�

THERE ARE NO USER SERVICEABLE PARTS INSIDE�

• THIS UNIT SHOULD BE INSTALLED ON A CLEAN FLAT SURFACE�

• THE GASKET ON THE BACK OF THE UNIT WILL PREVENT WATER INFILTRATION INSIDE, BEHIND THE MOUNTED

SURFACE� IF THE GASKET IS DAMAGED, SEAL THE BACK OF THE UNIT WITH SILICONE TO AVOID ANY LEAKAGE

BEHIND THE MOUNTED SURFACE�

• THIS UNIT MUST BE MOUNTED ON THE OUTSIDE EDGE OF THE SPA� SEE INSTALLATION SECTION FOR DETAILS�

• THE BACK OF THIS UNIT SHOULD NOT BE ENCLOSED IN A WAY THAT CAUSES WATER TO COLLECT�

SEE INSTALLATION SECTION FOR DETAILS�

* HAZARDOUS CONDITION:

A CONDITION THAT IS POTENTIALLY DAMAGING AND/OR DANGEROUS TO THE OPERATOR OR SURROUNDINGS�

THIS INCLUDES, BUT IS NOT LIMITED TO: FIRE, FLOODING OR OTHER WATER DAMAGE, DIELECTRIC BREAKDOWNS

(PRESENCE OF HIGH VOLTAGE), ETC�

MAINTENANCE

If you have problems, do not attempt to repair the unit yourself� Return it to your dealer or service station for servicing�

ACCESSORY PARTS

Be sure to use only the specified accessory parts� Use of other than designated parts may damage this unit internally or may

not securely install the unit in place� This may cause parts to become loose resulting in hazards or product failure�

DISPOSAL OF THE PRODUCT

The appliance (or the product) must be disposed of separately

in accordance with the local waste disposal legislation in force�

Compatible spa controllers:

in�xm2, in�xe, in�yt, in�yj and in�ye with compatible software revision�

Aeware®, Gecko®, and their respective logos are Registered Trademarks of Gecko Alliance Group�

in�k800™, in�xm2™, in�xe™, in�yt™, in�ye™, in�yj™, in�tune™, in�stream™, in�stream 2™, in�mix™, in�clear™, in�touch™

and in�therm™, and their respective logos are trademarks of Gecko Alliance Group�

All other product or company names that may be mentioned in this publication are tradenames, trademarks or registered

trademarks of their respective owners�

Warnings

in�k800

intuitive color keypad

With its bright, full color display, the in�k800 provides an

intuitive user experience, while its screen’s high resolution

brings hot tub user interfaces to a new level� Loaded

with a large amount of memory and a powerful on-board

processor we have created the seamless graphic interface

that spa users have been waiting for�

This techbook presents the different functions and menus

available on your in�k800� Availability of certain functions

depends on the software version of your in�k800� To find

out which features are available for your software version*

refer to the table of available options in the "Feature

matrix" section�

* To see which software version is installed on your in.k800

refer to the "About" section.

Introduction

in.k800 dimensions

8�73"

(221�74 mm)

4�23"

(107�47 mm)

2�03"

(51�57 mm)

Overview

Installation of in.k800

Installation

Gasket with or without adhesive

Optional wing nuts

and spacers

To install the in�k800, use the drilling template provided in this section�

Determine the mounting location and stick the template on chosen location�

Cut out an opening according to the template�

Clean the installation surface and peel the adhesive gasket from the back of the keypad�

Insert keypad and align it correctly, then ensure it is properly glued by gently pressing evenly on the entire surface�

3.5"

88.90 mm

0.125"

3.17 mm

R 0.250"

6.35 mm

R 0.625"

15.87 mm

8.00"

203.20 mm

7.5"

190.50 mm

Installation

Drilling template

in�k800 must be installed

on the outside edge of the

hot tub, so that it is not

subject to moisture trapped

by the cover�

The back of the in�k800 should not be enclosed where

water can gather, but instead cut out�

Vent hole on back of keypad should not be blocked�

Installation

Installation notes

Connecting in.k800 keypad to the spa pack

in.xe & in.xm 2

To connect the in�k800 keypad, simply insert its in�link

connector into the appropriate keypad connector of the

pack enclosure (as illustrated)�

Main keypad in�k800

in.ye & in.yt

To connect the keypad, remove the cover, then insert the

in�link connector into the appropriate keypad connector

(as illustrated)� Route the cable through one of the molded

strain relief channels on the bottom right side of the spa

pack (as illustrated)� Fill the remaining space with the

foam gaskets supplied� Don’t forget to replace the cover

and all screws (torque to 8 in� lb max (0�9 N�m))�

Upon connecting the in�k800 to the spa pack you may see one of two error messages:

Please follow the instructions in the message or contact your dealer for more information�

Installation

Installation errors

Keypad functions

Power

Press any button to turn the keypad on� After 30 minutes

without activity it will shut off�

Main screen

The main screen gives you access to your accessories and

water temperature� At the bottom of the screen you will

see any error or maintenance messages that are present�

Settings key

One press gives you access to a menu to manage the settings of your spa� Refer to the settings section for details about

the settings menu�

Mode key

Successive presses on the Mode key will give access to control different optional accessories of your spa such as Audio

and others� Note that if an accessory is not present in your spa configuration, its menu will not appear�

Refer to the following section to get details about the possible accessories and their detailed functionalities�

The screen will revert back to the spa mode if no key is pressed for 60 seconds�

Depending on pack configuration, Mode key may also be used to change the display orientation when an accessory is

not present�

Settings

Key 2

Key 3

Key 1

Mode

Key 4

Key 5

Down

Selection lights Light/ Key 6

* Functions for keys 1 to 5 will depend on your system's low level configuration.

in.k800 keypad layout

Start or stop accessories

To start or stop an accessory, press the associated button�

Icons will become animated when their accessory

is turned on, and inanimate when turned off�

Icons on the screen will reflect the speed or state

of the devices running on your spa�

When an accessory has more than two states,

press the button until it reaches the desired state�

Notifications

A notification area at the top right-hand side of the screen

shows the state of certain accessories installed in the spa�

Keypad functions

Notification icons

in.mix:

• Indicates that an in�mix system is detected�

For more information about the in�mix system,

refer to the in�mix functions section�

in.clear:

• The icon is green when the in�clear is

generating bromine�

• The icon is grey when the in�clear isn't

generating bromine�

• A red cross indicates that the in�clear is

turned off�

For more information about the in�clear,

refer to the in�clear functions section�

in.touch:

• Indicates that the in�touch module is detected

and connected to a Wi-Fi network�

• A red cross indicates that the in�touch module

is detected but isn't connected to a Wi-Fi

network�

For more information about the in�touch,

refer to the Wi-Fi section�

in.stream 2:

• The icon is green when the in�stream 2 is ON�

• The icon is grey when the in�stream 2 is OFF�

For more information about the in�stream 2,

refer to the in�stream 2 functions section�

Keypad security:

• Indicates that the keypad is locked�

For more information about keypad security,

refer to the keypad settings section�

Water temperature

The temperature at the bottom of the screen shows the

current water temperature� Use the Up and Down keys

to set the desired temperature� The set point will appear

in blue� After 3 seconds without any change to the set

temperature value, the current water temperature will

reappear�

When the set value is lower than the current temperature

Cooling to xx.x will appear below� When the set value is

higher than the current temperature, Heating to xx.x will

be indicated under the value� Normally there is a short

delay before the heating starts, during which Heating

Suspended is indicated under the value�

Settings

From the home page you can access the Settings,

where you will find:

• Water care

• Heat Pump (if installed)

• Audio

• in.clear-200 (linked version)

• Maintenance

• Date and time

• Keypad Settings

• Wi-Fi (only available on in.touch with software 11.00

or higher)

• Miscellaneous

• Electrical configuration

• About

Use the arrow keys to move up and down in the list�

To select an option, press the lit button next to it (key 2)�

At any point you can press the Settings button to return to

the home screen or key 1 to go back�

Keypad functions

Water care

The Water Care section will help you set up your ideal

filtration and heating settings� Choose from Away from

Home, Standard, Energy Savings, Super Energy Savings,

and Weekender, depending on your need�

Use key 2 to choose your setting� A green checkmark will

appear on the selected icon to confirm�

In Economy mode, the set point will be reduced by 20°F*,

which means that the heating system will not be engaged

unless the temperature falls to 20°F below the spa's set

temperature�

The filtration schedule shown on the screen will apply to

the main filtration pump, most likely pump 1� If your spa

uses a circulation pump configured to run 24 hours, the

screen will show you the purge setting instead of filtration�

The purges are pre-programmed for a fixed number of

minutes, therefore the duration will be set to N/A on the

screen, and only the start time can be modified�

* Default pack value

Keypad functions

Away:

In this mode the spa will always be in

economy; the set point will be reduced by

20° F�

Standard:

The spa will never be in economy mode

and will be filtering according to the

pack's low level configuration�

Energy Savings:

The spa will be in economy mode during

the peak hours of the day and resume

normal mode during the evening hours

and on the weekend�

Super Energy Savings:

The spa will always be in economy mode

during peak hours, every day of the week�

Weekender:

The spa will be in economy mode from

Monday to Friday, and will run normally

on the weekend�

Default Settings:

When you select Default Settings you will

be asked to confim your choice� Doing

so will restore all Water care schedules to

default settings�

Modifying schedules

To modify a Water Care mode, use the lit key to the right

(key 5) to open the selected Water Care menu� You can

add schedules by scrolling down to Add, and selecting

with key 2� To delete a schedule, press key 4� You can

modify the programmed schedules by selecting one and

adjusting the schedule using the arrow keys� Use key 2 to

move between parameters�

You have several possibilities for the schedule (Mon-Fri,

weekend, every day, or single days)� The schedules will

be repeated every week� The time and duration are set in

30 minute increments� Once you have set the schedule,

use key 1 to go back� Ensure that you have selected the

desired Water Care mode in the main Water Care menu�

Water care modes

Water care

Keypad functions

Heat pump

This menu allows you to change the regulation mode of

your heat pump� You can choose from Eco Heat, Smart

Heat, Eco Auto, Smart Auto, Cool and Electric�

A green checkmark indicates the currently selected

regulation mode� To change the setting, simply navigate

the menu using the arrow key and press key 2 to choose

the desired regulation mode�

Eco Heat

In this mode, the heat pump is used as

the unique source of heating� The heating

element is kept off and the heat pump

is not used to cool the water should its

temperature rise above the current set point�

Smart Heat

This mode uses the heat pump as the main

heating source� The heating element is

turned on only if there is a large temperature

difference between the water and the set

point� The heat pump is not used to cool the

water in this mode�

Eco Auto

This mode borrows functionality from both

Eco Heat and Cool modes and has the

ability to select the proper Heat or Cool

mode automatically according to the water

temperature� The heating element is never

activated in this mode�

Smart Auto

This mode borrows functionality from both

Smart Heat and Cool modes and has the

ability to select the proper Heat or Cool

mode automatically according to the water

temperature� The heating element is activated

only if there is a large temperature difference

between the water and the set point�

Cool

This mode uses the heat pump in cooling

mode only� The heat pump is not used as a

heating source and the heating element is

never activated�

Electric

This mode keeps the heat pump off and

uses only the heating element to regulate

water temperature�

Heat pump modes

Heat pump

Audio

The in�k800 can be used with the in�tune, in�stream or

in�stream 2 audio system�

The Audio section in the Settings menu gives you the

option to disconnect or unpair your Bluetooth enabled

device when using the in�stream�

The in�stream 2 Settings menu gives you a Bluetooth

disconnect feature and an audio control on fader, balance

and subwoofer�

For more information on audio functions, see the in�tune,

in�stream or in�stream 2 operation section�

Keypad functions

in.clear-200 (linked version)

The in�k800 keypad can be used with the in�clear

sanitization system� The in.clear section allows you to

configure your maintenance settings and Boost level�

For more information on maintenance and Boost settings,

see the in�clear user manual�

Use the Up and Down keys to make your selection,

then key 2 to confirm�

Use the Up and Down keys to change the maintenance or

Boost value, and key 2 to confirm�

* If the maintenance value is modified by more than 2,

a warning message will appear with an option to cancel or

confirm the change.

Maintenance

From the Settings page you can access the Maintenance

menu, which gives you access to the following options:

• Maintenance reminders

• Standby

Use the Up and Down keys to make a selection,

and key 2 to confirm�

Keypad functions

Maintenance reminders

The in�k800 keypad will remind you of maintenance

required on your spa, like rinsing or cleaning the filter�

Each task has its own duration, based on normal use�

The Maintenance reminders menu allows you to verify

the time left before maintenance is required, as well as to

reset the time once a task is completed�

Use the Up and Down keys to move through the list�

To reset a task select it by pressing key 2, then confirm

when prompted� Once you have confirmed the task will

be reset�

When you select Reset reminders you will be asked to

confim your choice� Doing so will reset

all

maintenance

reminders to default values�

Standby

The Standby mode allows you to service your spa�

Pumps will stop for 30 minutes, and automatically restart

after this time�

Once Standby

mode has been activated a screen will

appear to show that pumps are stopped� The spa page

will return at the end of maintenance�

Press on the Confirm key to leave Standby mode and

restart the spa�

Keypad functions

Date and time

Here you can adjust the time format, change the year,

date, and time� Use the arrows to choose the setting that

you want to adjust, and select it by pressing key 2�

Use the arrow keys to change the parameters, and key 2

to move between parameters� Key 1 will take you back to

the main Settings menu�

Keypad settings

In this section, you can change the temperature unit,

language, display orientation, rim light color* and

keypad security� Note the spa pack must be configured

accordingly to be able to change the rim light color�

Use the arrow keys to choose the setting that you want to

adjust� Select it by pressing key 2 then use the arrow keys

again to change the setting�

When you change the display orientation, the contextual

options and arrow keys adjust to the chosen orientation�

The Mode and Menu keys remain unchanged, as well as

the accessory keys in the main Spa menu�

You can lock the keypad by selecting one of 3 security

levels: Unlock, Partial or Full� The Partial level locks the set

point adjustment and many options in the settings menu�

The Full level locks all keypad functions� To unlock the

keypad (either Partial or Full), press and hold the top right

key for 5 seconds�

* Since v23.00, if an in.mix is installed, you can synchronize the

color of rim light with an in.mix zone.

Keypad functions

Wi-Fi (in.touch only)

For the Wi-Fi menu to appear in the Settings menu your

in�touch module must be equipped with software version

11�00 or higher� This menu allows you to connect your

in�touch module to a Wi-Fi network or to change its

network�

For more details about other in�touch connection methods

please see the in�touch techbook�

To connect your in�touch module to a wireless network,

use the Up/Down keys to go to the Wi-Fi option in the

Settings menu and key 2 to select it�

After a few seconds the available networks will appear on

the screen, as well as their signal strength�

Use the Up/Down keys to move through the list�

Select your network by pressing on key 2�

If the Wi-Fi network is password protected enter it when

prompted�

• Use the arrow keys to choose your letters

• Use key 6 to move the curser forward

• Use key 4 to change the type of character

(uppercase, lowercase, number, symbol)

• Use key 3 to backspace

• Use key 2 to confirm

If no password is required the in�touch will connect

automatically�

Once the in�touch module is connected to a

Wi-Fi network a green check mark will appear in

the Wi-Fi menu, and the network name will appear

in the Settings menu�

Keypad functions

Miscellaneous

In this section, you can change the Warm weather* and

Info messages options�

You can bypass the pack filtration over-temperature

feature� When Warm weather is "Off", the filtration over-

temperature is disabled� This feature allows the spa to

continue filtering even through the water temperature is

high�

You can configure the main window message center�

When set to Display, all information messages are

displayed without exception and when set to Hide, some

detailed messages are not

displayed when they occur to

keep the message center simple�

* Depending of pack configuration

Low level configuration Key 1 Key 2 Key 3 Key 4 Key 5 Key 6

1 pump Pump 1 --- --- --- --- Light

2 pumps Pump 1 Pump 2 --- --- --- Light

2 pumps + blower Pump 1 Pump 2 Blower --- --- Light

3 pumps Pump 1 Pump 2 Pump 3 --- --- Light

3 pumps + blower Pump 1 Pump 2 Pump 3 Blower --- Light

4 pumps Pump 1 Pump 2 Pump 3 Pump 4 --- Light

4 pumps + blower Pump 1 Pump 2 Pump 3 Pump 4 Blower Light

5 pumps Pump 1 Pump 2 Pump 3 Pump 4 Pump 5 Light

5 pumps + blower Pump 1 Pump 2 Pump 3 Pump 4 Pump 5 + blower Light

Electrical configuration

Please do not make changes in this section unless you

are a qualified electrician.

In this section you can change the low-level configuration,

number of phases, input current and heat pump current*�

Use the Up/Down Keys to move to the selection you want

to modify� Use Key 2 to select, and the Up/Down Keys

to move through the selections� Press Key 2 again to

confirm� Please see the techbook of your spa system for

details on low-level settings�

Once you have changed the Number of Phases in the

menu, you will be unable to use the Up/Down keys to

return to the Low-level configuration menu� Please go

back and access the menu again�

When you change de low-Level configuration of the pack,

all in�k800 settings will reset (same as Factory reset

feature)�

* Depending on the pack configuration, a code may be required

to change these settings. This code is “5555”.

Note that with a special low level configuration, it is possible that the blower has been set to always remain on key 5.

The table below shows the key assignation based on the accessories selected in your pack's low level configuration�

Please refer to the pack manual for specifications to identify the low level configuration for your spa�

Please note that if there are two spa packs in the system (i�e� a Swim Spa installation), the master unit’s chosen

configuration must support a slave unit� If, after re-booting, the chosen configuration does not support SwimSpa

installations, the in�k800 will return (after about 45 seconds) to this configuration menu and prompt the user to select

a configuration number again�

Keypad functions

About

This section shows information about the in�k800 software

number, and the revision numbers of the different

components of your system�

Keypad functions

Zone 1

Zone 3

Up and Down

for color changes

Mode

Zone 2

Press on the Mode key to access your in.mix.

This menu is only present if an in�mix system is detected� By default, the in�mix selects Zone 1 when you access the

menu� After the first use the menu will automatically

return to the last zone selected�

Zone selection

The zone selection keys allow you to select a zone to

modify its color�

• Press once to select the zone�

• Press a second time to deactivate the zone�

Changing colors

Once a zone is selected use the arrow keys to change the

colors by moving up and down in the color wheel�

Synchronizing zones

The synchronization/desynchronization key allows you to

match the color of the selected zone to the other zones�

Synchronisation

Desynchronization

This menu will only appear if an in�mix system is present�

in.mix functions

Press the Mode key to access your in.tune.

Source Power Volume Up/Down

Turning power on/off

Press the Power key to turn the in�tune on or off�

Selecting the source

Press the Source key to choose between CD, Auxiliary

input, and Radio�

If no source is selected, the in�tune will use the last

selected source�

Play/Pause audio

Press the Play/Pause key to start or pause the audio�

Adjusting the volume

Press the Volume Up or the Volume Down key

to increase or decrease the volume�

Changing tracks

Use the Last Track and Next Track keys to change tracks

for the CD or AUX input� When in Radio mode, the Last

Track and Next Track keys will move through preset radio

stations on the selected band� To change bands or preset

stations, see your in�tune manual�

in.tune functions

This menu is available only if the in�tune was selected in the audio configuration menu�

Keypad functions

See Factory reset/Audio configuration section for details on setting up audio�

Use the adapter cable (Part # 9920-400976) to connect the in�tune to the CO port of the spa pack�

Connecting the in.tune to the spa pack

Mode

Next track Play/ Pause

Last track

Press the Mode key to access your in.stream.

AUX

Next track Play/ Pause

Last track

Volume Up/Down

Mode

Bluetooth

If you are using a device with Bluetooth technology,

it must be connected for functions to work.

Please note that the Play/Pause and Change Track

functions apply to devices using Bluetooth technology

only, and will not work when AUX is selected as

the source.

Turning power On/Off

Press the Power key to turn the in�stream on or off�

Selecting the source

Press the Bluetooth key to select a device using Bluetooth

wireless technology�

Press the Source key to use a device connected

to the auxiliary cable�

If no source is selected, the in�stream system will

use the last selected source�

Play/Pause audio

Press the Play/Pause button to start or pause the audio�

Adjusting the volume

Press the Volume Up or the Volume Down key

to increase or decrease the volume�

Changing tracks

Use the Last Track and Next Track keys to change tracks�

Disconnect or Unpair Bluetooth

These options can be found under the Audio section

in the Settings menu�

in.stream functions

This menu is available only if the in�stream was selected in the audio configuration menu�

Keypad functions

Power

Connecting the in.stream to the spa pack

See Factory reset/Audio configuration section for details on setting up audio�

Use the adapter cable (Part # 9920-400976) to connect the in�stream to the CO port of the spa pack�

Press the Mode key to access your in.stream 2.

Source

Next track Play/ Pause

Last track

Mode

Mute

If you are using a device with Bluetooth technology,

it must be connected for functions to work.

Please note that the Play/Pause functions apply only

to Bluetooth and USB source. Change Track or station

functions works with all sources except AUX.

Turning power On/Off

Press the Power key to turn the in�stream 2 on or off�

Selecting the source

Press the Source key to toggle between available sources�

Play/Pause audio

Press the Play/Pause button to start or pause the audio�

Adjusting the volume

Press the Volume Up or the Volume Down key to increase

or decrease the volume�

Changing tracks

Use the Last Track and Next Track keys to change tracks�

Note that on FM these functions can be use to change

stations�

Disconnect

This option can be found under the Audio section

in the Settings menu�

Fader, Balance and Subwoofer

Fader, Balance and Subwoofer settings can be edited

under the Audio section in the Settings menu if your

in�stream 2 supports it�

in.stream 2 functions

This menu is available only if the in�stream 2 was detected at power up�

Keypad functions

Connecting the in.stream 2 to the spa pack

See Factory reset/Audio configuration section for details on setting up audio�

Use the CO cable to connect the in�stream 2 to the CO port of the spa pack�

Power Volume Up/Down

Diagnostic Mode

Press on the Diagnostic key to start a BromiCharge

concentration level test� To exit diagnostic mode press on

the Diagnostic key again� The system will automatically

exit after 15 minutes�

In diagnostic mode, the BromiCharge gauge indicates the

approximate level of BromiCharge in the spa water� Do not

add BromiCharge if the indicator is in the green zone�

When BromiCharge is added the indicator will move

slowly to the right� When water is added to the spa the

indicator will move to the left� To obtain a good level of

BromiCharge, start the pumps and add the specified

amount of BromiCharge** and allow 5 minutes for the

indicator to adjust before adding more�

For optimal performance, aim for the middle of the green

zone�

**For more information on adjusting your BromiCharge level

see the in.clear user manual.

Power

Boost activation/deactivation

Boost adjustment

Mode

Press on the Mode key to access your in.clear module.

This menu allows you to activate or deactivate your

in�clear, to start or stop a Boost, and to enter diagnostic

mode�

Turning the in.clear on/off

Press the power key to turn the in�clear on or off�

Control the Boost level

Press on the Boost activation/deactivation key to start a

Boost, and again to cancel�

To adjust the Boost level use the arrow keys�*

A message indicating that Boost mode is active is

displayed at the bottom of the main screen for the

duration of the Boost�

* See the in.clear user manual for more details about

Boost levels.

Diagnostic

This menu is only available if an in�clear linked is detected�

Keypad functions

in.clear functions

Code (not displayed) Message

HL High Limit circuit has tripped!

FLO - L01 FLO - L02 FLO FLO condition - Check filter, pump, blockage, air lock and water level

NO FLO Persistent NO FLO, all off - Check filter, pump, blockage, air lock and water level

HR A hardware error was detected (Relay stuck)

OH Spa temperature is too high

Prr Temp probes or detection circuit are defective

AOH Elevated internal temperature

FLC The pressure switch is closed

SP in Input voltage issue

RH NC Comm� error between in�xm2 - in�therm

RH ID in�xm2 and in�therm incompatible

SC ER Error detected during the learning mode

F1 in�xm2 Fuse # 1 is blown

F2 in�xm2 Fuse # 2 is blown

F3 in�xm2 Fuse # 3 is blown

ER1 SwimSpa config� : slave unit is missing

Hr Hardware error was detected (Thermal fuse)

UPL The spa pack does not have valid software�

Please insert valid in�stick to reprogram spa pack�

CFLO No Flow condition

HIBr Add fresh water to the spa

HiBr Add fresh water to the spa

LoBr Add BromiCharge to spa water

NoBr Add BromiCharge to spa water

Comm Verify cable connections

Supp Connect power cord to 240 V source

HP1-99 Heat Pump error! Service Code 1-99, Contact Dealer

The list below shows the different error messages that can appear on the home screen�

Refer to the troubleshooting and error codes section of the TechBook for your spa pack system�

Please note that if you are in swim spa configuration, the message may be followed by a "Master" or "Slave"

to designate from which pack the error is coming from�

Error messages

Keypad functions Earliest version

Power 3�00

Main screen 3�00

Notifications 12�00

Start or stop accessories 3�00

Water temperature 3�00

Settings 3�00

Water care 3�00

Water care modes 3�00

Modifying schedules 3�00

Audio 3�00

in�clear-200 (linked version) 6�00 **

Maintenance

Maintenance reminders 6�00

Standby 6�00

Service 24�00

Error log 6�00

Flow meter 19�00 (until version 24�00)

Factory reset 3�00

Date and time 3�00

Keypad settings

Temperature unit 3�00

Language

English 3�00

Français 3�00

Español 6�00

Polski 6�00

Nederlands 6�00

Deutsch 6�00

Norsk 6�00

Svenska 6�00

Magyar 15�00

Italiano 15�00

Português 15�00

esky 19�00

Display 12�00

Color 12�00

Security 18�00

Wi-Fi 6�00*

Electrical configuration 3�00

Miscellaneous

Warm weather 19�00

Info messages 24�00

in�mix functions 6�00

in�tune functions 3�00

in�stream functions 3�00

in�clear functions 6�00 **

in�stream 2 functions 16�00

Heat pump functions 29�00

About 3�00

Feature matrix

* Only available with the latest software version of the X and Y Series spa systems, and software version 11.00 or higher of the in.touch module.

** Only available with the latest software version of the X and Y Series spa systems.

The following table presents the features and/or options available for the in�k800 keypad, and the earliest software version

at which this feature/option is available� All versions greater than the earliest version continue to support the feature

(unless otherwise noted)�

Specifications are subject to change without prior notice.

Part number

0607-008025

Model

IN�K806-CL-GE1

Environmental

Operating temperature: -4°F (-20°C) to 149°F (65°C)

Storage temperature: -22°F (-30°C) to 185°F (85°C)

Water ingress protection: IPX5

Mechanical

Weight: 1�05 lbs (0�48 kg)

Dimensions (W x H x D): 8�730" x 4�231" x 2�029"

(221�74 mm x 107�47 mm x 51�57 mm)

Audio specifications

Audio source supported: in�tune, in�stream and in�stream 2

Compatibility

in�yt, in�ye, in�yj, in�xe, or in�xm2 spa packs with appropriate software revision

Specifications

in.k800

intuitive color keypad

TechBook

Gecko Alliance

450 des Canetons, Québec (Qc), G2E 5W6 Canada, 1.800.78.GECKO

www.geckoalliance.com Printed in Canada

9919-101191-K

Rev. 12-2019

All trademarks or registered trademarks

are the property of their respective owners.

Full color control

On-screen audio control

Water care selection

Gecko in.k800 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Gecko in.k800

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info