764968
3
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
in.k330
an affordable touch of luxury
TechBook
Gecko Alliance
450 des Canetons, Québec (Qc), G2E 5W6 Canada, 1.800.78.GECKO
www.geckoalliance.com Printed in Canada
9919-101654-A
Rev. 12-2019
© Groupe Gecko Alliance Inc., 2019
All trademarks or registered trademarks
are the property of their respective owners.
Classy look
Distinctive display
Perfect 2 pump affordable solution
1
Warnings ������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2
Introduction ��������������������������������������������������������������������������������������������������������������������������������������������������������������������� 3
in�k330 keypad layout ����������������������������������������������������������������������������������������������������������������������������������������������������� 4
in�k330 dimensions ��������������������������������������������������������������������������������������������������������������������������������������������������������� 5
Installation of in�k330 ������������������������������������������������������������������������������������������������������������������������������������������������������ 5
Drilling template ��������������������������������������������������������������������������������������������������������������������������������������������������������������� 6
Installation notes �������������������������������������������������������������������������������������������������������������������������������������������������������������� 7
Connecting in�k330 keypad to the spa control ���������������������������������������������������������������������������������������������������������������� 7
Keypad functions ������������������������������������������������������������������������������������������������������������������������������������������������������������� 8
-Start or stop accessories ������������������������������������������������������������������������������������������������������������������������������������� 8
-Water temperature ��������������������������������������������������������������������������������������������������������������������������������������������� 8
-Off Mode ������������������������������������������������������������������������������������������������������������������������������������������������������������ 8
-Keypad Lock ������������������������������������������������������������������������������������������������������������������������������������������������������� 8
-Custom key ������������������������������������������������������������������������������������������������������������������������������������������������������� 9
Programming steps ������������������������������������������������������������������������������������������������������������������������������������������������������� 10
-Program menu ������������������������������������������������������������������������������������������������������������������������������������������������� 10
-Setting the clock ����������������������������������������������������������������������������������������������������������������������������������������������� 10
-Programming the filter/ purge cycles ���������������������������������������������������������������������������������������������������������������� 10
-Setting filter or purge cycle start time ���������������������������������������������������������������������������������������������������������������� 11
-Setting filter cycle duration ������������������������������������������������������������������������������������������������������������������������������� 11
-Setting filter or purge cycle frequency �������������������������������������������������������������������������������������������������������������� 11
-Setting economy mode* ����������������������������������������������������������������������������������������������������������������������������������� 11
-Setting economy start time* ����������������������������������������������������������������������������������������������������������������������������� 12
-Setting economy duration* ������������������������������������������������������������������������������������������������������������������������������� 12
-Heat pump regulation mode ���������������������������������������������������������������������������������������������������������������������������� 12
-Setting temperature unit ����������������������������������������������������������������������������������������������������������������������������������� 13
Smart Winter Mode ������������������������������������������������������������������������������������������������������������������������������������������������������� 14
Cooldown ���������������������������������������������������������������������������������������������������������������������������������������������������������������������� 14
Water temperature regulation ���������������������������������������������������������������������������������������������������������������������������������������� 14
Error messages �������������������������������������������������������������������������������������������������������������������������������������������������������������� 15
Specifications ���������������������������������������������������������������������������������������������������������������������������������������������������������������� 16
Table of contents
2
WARNINGS:
Before installing or connecting the unit, please read the following�
FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS MAY SIGNIFICANTLY SHORTEN THE PRODUCT’S
LIFE TIME, AND LEAD TO FAILURES AS WELL AS HAZARDOUS CONDITIONS*. COMMON SENSE MUST
ALWAYS PREVAIL WHEN EVALUATING THE INSTALLATION AND/OR USE OF ANY ELECTRONIC CONTROL IN
A FINAL APPLICATION.
RESPECT ENVIRONMENTAL CONDITIONS LISTED AT END OF TECHBOOK�
THIS UNIT MUST BE INSTALLED BY QUALIFIED PERSONNEL�
ONLY QUALIFIED PERSONNEL ARE TO SERVICE THIS UNIT�
THERE ARE NO USER SERVICEABLE PARTS INSIDE�
THIS UNIT SHOULD BE INSTALLED ON A CLEAN FLAT SURFACE�
THE GASKET ON THE BACK OF THE UNIT WILL PREVENT WATER INFILTRATION INSIDE, BEHIND THE
MOUNTED SURFACE� IF THE GASKET IS DAMAGED, SEAL THE BACK OF THE UNIT WITH SILICONE TO AVOID
ANY LEAKAGE BEHIND THE MOUNTED SURFACE�
THIS UNIT MUST BE MOUNTED ON THE OUTSIDE EDGE OF THE SPA� SEE INSTALLATION SECTION FOR
DETAILS�
THE BACK OF THIS UNIT SHOULD NOT BE ENCLOSED IN A WAY THAT CAUSES WATER TO COLLECT�
SEE INSTALLATION SECTION FOR DETAILS�
* HAZARDOUS CONDITION:
A CONDITION THAT IS POTENTIALLY DAMAGING AND/OR DANGEROUS TO THE OPERATOR OR
SURROUNDINGS� THIS INCLUDES, BUT IS NOT LIMITED TO: FIRE, FLOODING OR OTHER WATER DAMAGE,
DIELECTRIC BREAKDOWNS (PRESENCE OF HIGH VOLTAGE), ETC�
MAINTENANCE
If you have problems, do not attempt to repair the unit yourself� Return it to your dealer or service station for servicing
ACCESSORY PARTS
Be sure to use only the specified accessory parts� Use of other than designated parts may damage this unit internally or
may not securely install the unit in place� This may cause parts to become loose resulting in hazards or product failure�
DISPOSAL OF THE PRODUCT
The appliance (or the product) must be disposed of separately
in accordance with the local waste disposal legislation in force�
Compatible spa controls:
in�yt, in�yj, and in�ye with compatible software revision�
Aeware®, Gecko®, and their respective logos are Registered Trademarks of Gecko Alliance Group�
in�k330™, in�yt™, in�ye™, and in�yj™ and their respective logos are trademarks of Gecko Alliance Group�
All other product or company names that may be mentioned in this publication are tradenames,
trademarks or registered trademarks of their respective owners�
Warnings
3
in�k330
An affordable touch of luxury
With its larger dimension, sleekness and its backlit outer
rim, Gecko’s in�k330 is an affordable alternative for those
who want to experience luxury� Its design will enhance the
look of any spa�
Completely ergonomic, our new in�k330 has a big LCD
screen with excellent contrasts and brightness� Its static
colors and 5 keys make it so easy to use� A classy and
ergonomic keypad, that’s the perfect combination!
Our solidly built in�k330 supports Gecko’s in�lu�me LED
system and our brand new in�temp� It brings all the
features you really need to one keypad� It is the perfect
choice for your customers who want quality on a budget!
Item in.k330
Static LCD size (as measured
diagonally)
1�5" (38 mm)
Integrated brackets
Double-sided bezel gasket
Colored icons giving instant spa
status information
Number of pumps/blowers supported up to 3
in�lu�me output support
in�temp support
Introduction
4
Up & Down
Up & Down Pump 2
Light
Light
Program/
Custom*
* optional function
Pump 1
Pump
Light indicatorPump 1 indicator
Pump indicator
Pump 2 indicator
Light indicator
1 Pump Model
Display interface
2 Pump Model
Set Point
Smart Winter Mode
Heater
Filter
in.k330 keypad layout
5
Installation of in.k330
To install the in�k330, use the drilling template provided in this section�
Determine the mounting location and stick the template on chosen location�
Cut out an opening according to the template�
Clean the installation surface and peel the adhesive gasket from the back of the keypad�
Insert keypad and align it correctly, then ensure it is properly glued by gently pressing evenly on the entire surface�
Gasket with or without adhesive
Optional wing nuts
and spacers
2�98"
(76 mm)
7�20"
(183 mm)
2�36"
(60 mm)
in.k330 dimensions
6
Drilling template
6�20"
[157�47 mm]
R0�50"
[R12�70 mm]
4X
2�19"
[55�71 mm]
7
It is recommended to install
the in�k330 on the outside
edge of the hot tub, so that
it is not subject to moisture
trapped by the cover�
The back of the in�k330 should not be enclosed where
water can gather, but instead cut out�
Keypad placement
Connecting in.k330 keypad to the spa control
Vent hole on back of keypad should not be blocked�
Installation notes
Main keypad in�k330
To connect the keypad, remove the cover, then insert the in�link connector into the appropriate keypad connector
(as illustrated)� Route the cable through one of the molded strain relief channels on the bottom right side of the spa
pack (as illustrated)� Fill the remaining space with the foam gaskets supplied� Don’t forget to replace the cover and all
screws (torque to 8 in� lb max (0�9 N�m))�
8
Start or stop accessories
To start or stop an accessory, press the associated button� Indicators will light up when the associated accessory is on�
When an accessory has more than two states, press the button until it reaches the desired state� Indicators will
flash when dual speed pumps are on at low speed, and will be solid at high speed�
If you have a blower it will be controlled by the Pump 2 key� The order of actions is as follows: pump 2 on;
pump 2 high speed (if applicable); blower on; pump 2 off; blower off�
Keypad functions
Water temperature
The temperature shown on screen is the current water
temperature� Use the Up and Down buttons to set
the desired temperature�
The set point icon will appear at the top of the screen�
After 3 seconds without any change to the set temperature
value, the keypad will resume the normal display�
Off Mode
Pressing Pump 1 for 5 seconds will enable the Off mode�
This mode allows you to stop all outputs including
automatic functions such as filter cycle, heat request and
smart winter mode for 30 minutes to perform quick spa
maintenance� When Off mode is active, the display will
toggle between the “OFF” message, the clock and the
water temperature� Press Pump 1 or Pump 2 (if available)
to restart the system before the expiration of the 30 minute
delay� When the system resumes its normal operation, the
display shows “On“ for 3 seconds�
Keypad Lock
(Available only if the lock feature is enabled in the spa
controller configuration)
You can lock the keypad by selecting one of 2 security
levels: Partial or Full� The Partial level locks the set
point adjustment and many options in the settings menu�
The Full level locks all keypad functions�
Partial lock activation
Press both arrow keys simultaneously for 5 seconds�
The keypad will display "LocP"� Release both keys to
engage Partial lock�
Full lock activation
Press both arrow keys simultaneously for 5 seconds�
The keypad will display "LocP"� Keep pressing both arrow
keys for 5 more seconds (10 seconds total)� The keypad
will display "LocF"� Release both keys to engage Full lock�
To unlock the keypad (either Partial or Full), press and
hold both arrow keys for 5 seconds; the "uLoc" message
will be displayed for a few seconds as a confirmation�
9
Keypad functions
Custom key
This key is available for 1-pump systems only� It is also
available only if the spa controller configuration uses a
functionality related to the Custom key�
The following functions are available on this key:
• Quick On Off
• Soak
• Auxiliary output
• Off
• Manual Economy
A short press on the Custom key will turn on or off the selected mode in the list�
Quick On Off
This function allows you to shut down all the active user
demands (pump and light) by a key press and resume
their state by another press�
Activating or deactivating Quick On Off mode with the
Custom key will have no special message being displayed�
Soak
This function allows you to soak in silence in the spa�
When enabled, Soak mode stops all pumps activated by
the user as well as the filtration and Smart Winter Mode
cycles for 30 minutes�
Water temperature regulation remains active as well as
circulation pump if it is configured as “Always On”�
While Soak mode is engaged, the display toggles between
the "Sby", the time and the water temperature� The display
will show "On" for 3 seconds upon exit of Soak mode
Auxiliary output
It allows you to control an auxiliary output� When the
control of the Auxiliary is selected by the Custom key,
"AUX" blinks on the display� Then, the Auxiliary can be
turned On or Off by another press on the Custom key�
When the Auxiliary output is being turned on, the display
shows "On" for 3 seconds� When the Auxiliary is being
turned off, the display shows "OFF" for 3 seconds�
Auxiliary output will be turned off automatically after
20 minutes if it is not done manually� Note that your spa
controller can be configured with a different timeout�
Off
(Described previously in this document)
Manual Economy
This mode allows you to lower the temperature set point
of the spa by 20 °F (11 °C)� When the Economy mode is
ON, the display toggles between the “Eco” message, the
time, and the water temperature� The display will show
"noE" for 3 seconds upon exit of Economy mode
10
Program menu
Instructions listed in this section assume the Program key is
used, but if there is no Program key on the keypad, use the
Light key instead.
The program menu is accessible by holding down the
Program key for 5 seconds� In the program menu the
following parameters can be set: clock, filter or purge cycles,
economy mode, heat pump mode and temperature units�
While in the program menu, use the Up or Down key to
adjust the parameters and use the Program key to jump
to the next parameter� The changes will be saved after the
confirmation of the last parameter only�
If there is no action taken for 15 seconds, the system will exit
the program menu and all changes will be saved�
Setting the clock
Enter the program menu by holding down the Program key
for 5 seconds� The display will show the current clock setting
with the hour flashing�
Depending on factory settings, your system may be set
to 24-hour time or 12-hour time� An additional dot can be lit
under the “:” separating hours and minutes to serve as an
AM icon�
Setting the hour: Use the arrow keys to adjust the hour� Press
the Program key to jump to the next parameter, the minutes�
Setting the minutes: Use the arrow keys to adjust the
minutes� Press the Program key to jump to the next
parameter, the filter or purge start time (FS)�
Programming the filter/ purge cycles
Depending on system configuration, your spa will
perform either a filter or a purge cycle� The filter cycle
menu consists of the following parameters: the start time
(FS), the duration (Fd) and the frequency (FF)� The purge
cycle menu consists of the following parameters: the start
time (FS) and the frequency (FF)�
A filter cycle consists of starting all the pumps and blower
in high speed for 1 minute (purge step) then, the pump
associated with the filter will run in low speed for the
remaining duration of the filter cycle (clean step)�
A purge cycle is used when the spa is equipped with a
24 hour circulation pump which provides a continuous
clean step� It consists of starting all the pumps and blower
in high speed for 1 minute�
Programming steps
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gecko in.k330 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gecko in.k330 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Gecko in.k330

Gecko in.k330 Gebruiksaanwijzing - Français - 18 pagina's

Gecko in.k330 Gebruiksaanwijzing - Espanõl - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info