691272
5
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Introduction
WARNING
Read all instructions carefully before installing and using the
Vector system. Improper use could result in serious injury.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
NOTE: For more information, go to www.garmin.com/manuals
/vector3 or www.support.garmin.com.
Thank You
Thank you for your Vector 3 or Vector 3S purchase. This manual
covers both Vector systems.
Vector was designed for cyclists, by cyclists, to provide an
outstanding experience of owning a precision power
measurement system for your bike.
Vector is simple, accurate, and easy to use.
Now it's time to put the power under your feet and get out there
and ride.
Getting Started
1
Install the Vector components (Installing the Vector
Components, page 1).
2
Install the shoe cleats (Installing the Shoe Cleats, page 1).
3
Pair the Vector system with your Edge
®
device (Pairing
Vector with Your Edge 1030, page 2).
4
Go for a ride (Your First Ride, page 2).
5
View your history (Vector Data, page 3).
6
Send your history to your computer (Sending Your Ride to
Garmin Connect, page 3).
Tools Needed
15 mm pedal wrench
Bike grease
3 mm hex key
4 mm hex key
Installing the Vector Components
The installation steps for the Vector 3 and Vector 3S systems
are very similar. Procedures that are specific to the Vector 3S
system are noted.
Preparing for the Installation
1
Remove the existing pedals.
2
Clean the threads, and remove old grease.
Installing the Pedals
This procedure is for the Vector 3 system. The Vector 3S system
installation is the same, but the power sensor components are in
the left pedal only. For more information, see About the Vector
3S System, page 2.
1
Install the right pedal first.
2
Apply a thin layer of grease on the pedal spindle threads.
3
Insert the spindle into the crank arm.
4
Hand tighten the spindle.
5
Use the pedal wrench to tighten the spindle.
NOTE: Garmin
®
recommends torque of 25 lbf-ft. (34 N-m).
6
Repeat steps 2 through 5 to install the left pedal.
NOTE: The left pedal spindle has a left-handed (reverse)
thread.
7
Move your bike chain to the largest chain ring and the
smallest cassette gear.
8
Rotate the crank arm to check for clearance.
NOTE: Garmin recommends 2 mm or more between the
pedal and the chain. If the pedal rubs the chain, you can add
one washer (included) between the spindle and the crank
arm to increase clearance. To maintain an equal q factor, you
can add one washer to the left pedal spindle. Do not use
more than one washer on each pedal.
Pedal Status LED
LED flashes indicate a system issue that requires your attention.
Error codes are cleared after the issue is resolved and you have
synced your Vector system with the Garmin Connect
Mobile
app or your Edge device. The LED is located on the inboard of
the spindle
À
.
LED Activity Status
1 red flash The Vector system is active and
working properly.
3 green flashes every 10
seconds
The pedal is searching for the other
pedal.
Alternating red and green
flashes
A software update is in progress.
20 green flashes The software update was successful.
20 red flashes The software update failed.
1 red flash every 10 seconds The pedal batteries are low.
Installing the Shoe Cleats
NOTE: The left and right cleats are the same.
1
Apply a thin layer of grease on the cleat bolt threads.
Introduction 1
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin Vector 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin Vector 3 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin Vector 3

Garmin Vector 3 Gebruiksaanwijzing - Nederlands - 14 pagina's

Garmin Vector 3 Gebruiksaanwijzing - Deutsch - 16 pagina's

Garmin Vector 3 Gebruiksaanwijzing - Français - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info