Handleiding Garmin VHF 315 serie (pagina 14 van 18) (Engels)

691459

Verklein

Vergroot

Pagina terug

1/18

Pagina verder

VHF 315 SERIES

Owner’s Manual

products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates

and supplemental information concerning the use of this product.

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GHS

™

is a trademark of Garmin Ltd. or its subsidiaries. These

trademarks may not be used without the express permission of Garmin.

NMEA

and NMEA 2000

are registered trademarks of the National Marine Electronics Association. NOAA

is a registered service mark of the National Oceanic and Atmospheric Administration.

BoatU.S.

is a registered trademark of the Boat Owners Association of the United States. Sea Tow

is a registered trademark of Sea Tow Services International, Inc. United States Power

Squadrons

is a registered trademark of the United States Power Squadrons. Other trademarks and trade names are those of their respective owners.

Table of Contents

Introduction.....................................................................1

Handset Overview...................................................................... 1

Home Screen.............................................................................. 1

System Status Icons.............................................................. 1

Basic Operation.............................................................. 1

Turning On and Off the Device................................................... 1

Adjusting the Volume.................................................................. 1

Adjusting the Squelch Level....................................................... 1

Selecting the Frequency Band................................................... 2

Selecting a Channel....................................................................2

Transmitting with the Radio........................................................ 2

Scanning and Saving Channels................................................. 2

Scanning All Channels........................................................... 2

Saving a Channel...................................................................2

Removing a Saved Channel.................................................. 2

Scanning Saved Channels.................................................... 2

Monitoring Multiple Channels.................................................2

Selecting a Different Second-Priority Channel........................... 2

Switching to Priority Channels.................................................... 3

Setting the Receiving Sensitivity.................................................3

Switching Between 1 W and 25 W Transmitting Modes............. 3

Bypassing the Low Transmission Power Setting................... 3

Using the Hailer Function........................................................... 3

Foghorn...................................................................................... 3

Sounding the Foghorn Automatically..................................... 3

Sounding the Foghorn Manually............................................ 3

Adjusting the Sound Frequency of the Foghorn.................... 3

Entering Text.............................................................................. 4

NOAA® Weather Broadcasts and Alerts...................... 4

Tuning Weather Broadcasts....................................................... 4

Enabling and Disabling Weather Alerts...................................... 4

Digital Selective Calling................................................. 4

Digital Selective Calling.............................................................. 4

Entering Your MMSI Number......................................................4

Viewing Your MMSI Number...................................................... 4

Distress Calls.............................................................................. 4

Sending an Undesignated Distress Call................................ 4

Sending a Designated Distress Call...................................... 5

Waiting For and Receiving and Acknowledgment for a

Distress Call........................................................................... 5

Stopping Automatic Retransmission of Distress Calls........... 5

Revoking a Distress Call........................................................ 5

Placing Calls............................................................................... 5

Placing Individual Calls.......................................................... 5

Placing Group Calls............................................................... 5

Placing All-Ships Calls........................................................... 5

Individual Call or Group Call Channels.................................. 6

Requesting a Vessel's Position.............................................. 6

Receiving Calls........................................................................... 6

Receiving Distress Calls and Distress Relay Calls................ 6

Receiving All-Ships Urgency and Safety Calls...................... 6

Receiving Individual Routine Calls.........................................6

Receiving Position Requests................................................. 6

Receiving Position Calls........................................................ 6

Receiving Group Calls........................................................... 6

Position Tracking........................................................................ 7

Selecting Vessels and Activating Position Tracking.............. 7

Viewing and Deactivating Vessels on the Position Tracking

List......................................................................................... 7

Deleting a Vessel From the Position Tracking List................ 7

Call Log.......................................................................................7

Viewing the Calls in the Call Log........................................... 7

Placing a Call from a Call Log................................................7

Saving a Vessel or Station to the Directory from the Call

Log......................................................................................... 7

Deleting a Call Log Entry....................................................... 7

Directory..................................................................................... 7

Viewing Saved Vessels and Stations in the Directory........... 7

Adding an Entry to the Directory............................................ 7

Editing an Entry in the Directory............................................ 8

Deleting an Entry from the Directory...................................... 8

Adding a Group...................................................................... 8

Editing a Group...................................................................... 8

Deleting a Group.................................................................... 8

DSC Settings.............................................................................. 8

Manual Position Information.................................................. 8

Changing the Channel to 16 Automatically............................ 8

Sending Automatic Replies.................................................... 8

Automatic Transmitter Identification System.............. 8

Entering Your ATIS Identification Number.................................. 8

Turning On and Off ATIS............................................................ 9

Viewing Your ATIS Identification Number.................................. 9

NMEA 0183 and NMEA 2000®....................................... 9

Additional Functionality with Other Garmin Devices................... 9

Communicating Over NMEA 0183 or NMEA 2000..................... 9

Configuring DSC NMEA Transmissions..................................... 9

System Settings............................................................. 9

Number Settings......................................................................... 9

Units Settings..............................................................................9

Configuring the Time Offset................................................. 10

Selecting the Frequency Band................................................. 10

Changing a Channel Name...................................................... 10

Restoring Factory Settings....................................................... 10

Appendix....................................................................... 10

Alarms and Messages.............................................................. 10

Channel Lists............................................................................ 10

VHF 315 Series Specifications................................................. 10

NMEA....................................................................................... 10

NMEA 0183 IN Sentences Supported................................. 10

NMEA 0183 OUT Sentences Supported............................. 10

NMEA 2000 PGN Information.............................................. 10

Cleaning the Outer Casing....................................................... 11

Index.............................................................................. 12

Table of Contents i

Introduction

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

Handset Overview

Item Key Description

PTT Hold to broadcast.

DISTRESS Lift the door and press to send a DSC distress

call with a programmed MMSI number

(Entering Your MMSI Number, page 4).

Press the key that corresponds to the on-

screen item to select the item.

ENTER On the home screen, rotate to change the

channel.

On the home screen, press to toggle weather

channels (NOAA

Weather Broadcasts and

Alerts, page 4).

Rotate to change the volume or squelch level

after pressing the VOL/SQ key.

Rotate to highlight an item in a list.

Press to select an item.

PWR

North America:

16/9

International:

16+

Hold to turn the radio on and off.

Press to toggle between preset channels.

HI/LO Press to change the transmission mode and

power settings.

CLEAR Press to return to the previous menu option.

Press to cancel or mute an incoming DSC call.

MENU From the home screen, press to view

configuration options.

From a menu, press to return to the home

screen.

DSC Press to view a menu of DSC options.

VOL/SQ Press to switch between volume or squelch.

Home Screen

Radio system status, settings, and alerts.

International, Canadian, or USA frequency band

*Latitude

*Longitude

*Time

**Speed over ground (SOG) or course over ground (COG)

Soft-key functions change depending on your current activity

Working channel

*The latitude, longitude, and time appear when the radio has a

GPS signal acquired. You can enter data manually when the

radio does not have a GPS signal.

** The SOG and COG appear when the radio has a GPS signal

acquired, and the option is enabled in the menu (Number

Settings, page 9).

System Status Icons

Icon Status

Receiving an incoming signal

Transmitting

Transmitting at 25 W

Transmitting at 1 W

Saved channel

Local receiver mode, often used in areas with radio frequency

interference (harbors)

ATIS enabled

Position tracking enabled

Auto channel changing disabled

Incoming or missed DSC call

Weather alert

GPS signal acquired

Basic Operation

Turning On and Off the Device

Hold PWR.

TIP: You can set the device to turn on automatically (System

Settings, page 9).

Adjusting the Volume

Set the squelch level to MIN before you adjust the volume

(optional).

Select VOL/SQ twice.

VOLUME appears on the screen.

Turn the dial to increase or decrease the volume.

Adjusting the Squelch Level

You can adjust the sensitivity level of the squelch to filter out

background noise. When you increase the squelch level, you

hear fewer weak background signals when you are receiving.

Select VOL/SQ.

SQUELCH appears on the screen.

Turn the dial counter-clockwise until you hear audio.

Turn the dial clockwise until there is no background noise.

Introduction 1

Selecting the Frequency Band

You can switch between the USA, International, or Canadian

frequency bands (Channel Lists, page 10).

NOTE: Not all frequency bands are available on all device

models.

Select MENU > CHANNEL > FREQUENCY BAND.

Select a frequency band.

Selecting a Channel

You can select an International, Canadian, or USA channel

(Selecting the Frequency Band, page 2).

Turn the dial.

Transmitting with the Radio

Select an appropriate channel.

Verify that the channel is clear.

NOTE: You cannot obstruct the communications of other

people due to Federal Communications Commission (FCC)

and international guidelines.

Select PTT on the handset.

appears at the top of the screen.

Speak into the handset.

NOTE: Five minutes is the maximum time allowed for

transmission. After five minutes of transmitting, PTT is

disabled until you release PTT.

Release PTT.

Scanning and Saving Channels

Scanning All Channels

When you scan channels, the radio searches for channels that

are broadcasting. When a channel is broadcasting, the radio

pauses on that channel until the broadcast stops. After four

seconds of inactivity on a channel, the radio resumes scanning.

NOTE: When you turn on ATIS (Automatic Transmitter

Identification System, page 8), the radio does not scan or

save channels.

Select SCAN > ALL.

Select an option:

• To exclude the currently active channel from subsequent

passes and resume scanning, select SKIP.

• To scan channel 16 each time another channel is

scanned, select +CH16.

For example, the radio scans channel 21, channel 16,

channel 22, channel 16, and so on.

+CH16 appears on the device screen.

• To scan channel 16 in its usual order, select -CH16.

For example, the radio scans channel 14, channel 15,

channel 16, channel 17, and so on.

• To end the scan, select EXIT.

The radio stops scanning and tunes to the last used,

active channel.

Saving a Channel

You can save any channel except the weather (WX) channels.

You can save an unlimited number of channels.

Select SCAN.

Turn the ENTER dial until you find a channel you want to

save.

Select SAV CH.

appears above a saved channel.

Removing a Saved Channel

Select SCAN.

Turn the ENTER dial until you find a saved channel.

NOTE: A saved channel has above it.

Select SAV CH.

Scanning Saved Channels

You can scan only the channels you have saved. When a saved

channel is broadcasting, the radio pauses on that channel until

the broadcast stops. After four seconds of inactivity on a

channel, the radio resumes scanning.

NOTE: When you turn on ATIS (Automatic Transmitter

Identification System, page 8), the radio does not scan or

save channels.

Select SCAN > SAVED.

Select an option:

• To exclude the currently active channel from subsequent

passes and resume scanning, select SKIP.

• To scan channel 16 each time another saved channel is

scanned, select +CH16.

For example, the radio scans saved channel 21, channel

16, saved channel 25, channel 16, and so on.

+CH16 appears on the device screen.

• To stop scanning channel 16, select -CH16.

For example, the radio scans saved channel 21, saved

channel 25, and so on.

• To end the scan, select EXIT.

The radio stops scanning and tunes to the last used active

channel.

Monitoring Multiple Channels

Before you can monitor multiple channels, you must turn off

ATIS (Automatic Transmitter Identification System, page 8).

You can monitor priority channels and the currently selected

channel for broadcasting activity. Channel 16 is the first-priority

channel on your radio. Channel 9 is the default second-priority

channel. You can program a different channel as your second-

priority channel (Selecting a Different Second-Priority Channel,

page 2).

Select WATCH.

Monitoring Two Channels

You can monitor your current channel and channel 16 at the

same time.

Select WATCH > DUAL.

DUAL WATCH and the channels you are monitoring appear

on the screen. For example, DUAL WATCH CH:, and 16 + 9.

Monitoring Three Channels

You can monitor your current channel, channel 16, and your

second-priority channel at the same time.

Select WATCH > TRI.

TRI WATCH, your current channel, channel 16, and your

second-priority channel appear on the screen. For example,

TRI WATCH CH:, and 75 + 16 + 9.

Selecting a Different Second-Priority

Channel

You can select a channel other than channel 9 as your second-

priority channel.

Select MENU > CHANNEL > 2ND PRIORITY.

Turn the ENTER dial to the preferred channel.

Select OK.

2 Basic Operation

Switching to Priority Channels

You can quickly switch between your current working channel

and a priority channel. When you change to a priority channel,

the transmit power is set to high (25 W) automatically, and when

you change back to your current channel, the transmit-power

setting is restored.

On North American models, you can quickly switch between

channel 16, your second-priority channel, and your original

channel using the 16/9 key.

On International models, you can quickly switch between

channel 16 and your original channel using the 16+ key.

To switch from your current channel to channel 16, select

16/9 or 16+.

The transmit power changes to high (25 W) automatically.

You can select HI/LO > 1W to change the transmit power to

low (1 W).

On North American models, select 16/9 to switch to your

second-priority channel.

Select 16/9 or 16+ to return to your previous channel and

transmit-power setting.

Setting the Receiving Sensitivity

You can control the receiving sensitivity of the radio. When you

have noise in high-traffic areas or areas with electromagnetic

interference, such as near cell-phone towers, you can set the

receiving sensitivity to LOC to decrease receiver sensitivity. In

remote areas and on open water, you can set the receiving

sensitivity to DIST to ensure that you use the maximum range of

the receiver.

Select HI/LO.

Select an option:

• Select LOC to enable local sensitivity.

• Select DIST to enable distant sensitivity.

Switching Between 1 W and 25 W

Transmitting Modes

You can control the transmitting power of the radio. Low (1 W) is

used for local transmissions, and high (25 W) is used for

distance and distress transmissions.

When two signals broadcast on the same frequency, a VHF

radio receives only the stronger of the two signals. You should

transmit calls other than distress calls using the lowest power

setting that allows you to communicate, to reduce the possibility

that your transmissions interfere with the transmissions of

others.

In the USA frequency band, transmissions on channels 13 and

67 must be low (1 W) by default. You can bypass the power

setting temporarily during transmission (Bypassing the Low

Transmission Power Setting, page 3).

In the International channel band, transmissions on channels 15

and 17 must be low (1 W), and the radio does not allow

transmissions on these channels to be changed to high (25 W).

Select HI/LO.

Select 1W or 25W.

Select OK.

Bypassing the Low Transmission Power Setting

In the USA frequency band, transmissions on channels 13 and

67 are required to be low-power (1 W) by default, because they

are intended for intership (bridge-to-bridge) communication. If

other radios cannot receive these channels due to the low power

setting, you can bypass the default restriction.

From USA channels 13 or 67, select PTT.

While transmitting, select 25W.

Using the Hailer Function

Before you can use the hailer function, you must install a hailer

horn (optional). For more information, see the VHF 315 Series

Installation Instructions.

A hailer horn allows you to make on-boat or ship-to-shore

announcements, and allows two-way communications between

connected radios. You can address the ship using the radio or

handset, and sounds received through the horn can be heard

through the radio speaker. For vessels with enclosed cabins, the

hailer horn allows you to hear sounds from the deck.

NOTE: When the radio is in hailer mode, it does not receive

broadcasts from the active channel.

Select PA > HAILER.

Sounds received through the horn are heard through the

radio speaker.

Hold PTT.

Select an option:

• To make an announcement, speak into the handset.

• To adjust the volume of the hailer broadcast, turn the

ENTER dial.

Release PTT to stop broadcasting and listen for broadcasts

from other connected radios on the ship.

Foghorn

NOTE: Foghorn functionality is not available on all VHF radio

models.

Before you can use the foghorn, you must provide and install a

hailer horn (optional) on the deck or tower of your boat. For

more information, see the VHF 315 Series Installation

Instructions.

The foghorn is part of the public address system of your radio.

You can sound the foghorn through a hailer horn or an external

speaker. Your radio can sound the horn automatically using

standard patterns, or you can sound the horn manually. When

you manually operate the foghorn, sounds received through the

horn can be heard through the radio speaker between

soundings.

Sounding the Foghorn Automatically

Select PA > FOG > AUTO.

Select a foghorn-type option.

The radio alternates between sounding the pattern of tones

or rings and receiving radio broadcasts.

Turn the ENTER dial to adjust the volume of the horn

(optional).

Sounding the Foghorn Manually

NOTE: When you sound the horn manually, the radio does not

receive broadcasts between horn soundings.

Select PA > FOG > MANUAL.

Sounds are received through the horn and heard through the

radio speaker.

Hold PTT.

NOTE: The horn stops sounding when you release PTT.

Turn the ENTER dial to adjust the volume of the horn

(optional).

Adjusting the Sound Frequency of the Foghorn

You can increase or decrease the sound frequency of the

foghorn. The pitch of the tone rises with an increase in

frequency, and falls with a decrease in frequency. The minimum

setting is 200 Hz, and the maximum setting is 850 Hz. The

default setting is 350 Hz. Regulations dictate the correct

frequency of foghorns, which correlate with the size of your

vessel.

Basic Operation 3

Select MENU > SYSTEM > FOG FREQUENCY.

Turn the ENTER dial to adjust the frequency in 50 Hz

increments.

Select ACCEPT.

Entering Text

You may need to enter a name, a number, or other text on the

radio.

From a number or text field, turn the ENTER dial to change

the number, letter, or character.

Press the ENTER dial to accept the number, letter, or

character and move to the next space in the sequence.

Repeat this process for each number, letter, or character.

NOTE: You can select to return to the previous entry in

the sequence.

Select ACCEPT.

NOAA

Weather Broadcasts and Alerts

NOTE: This feature is not available on all radio models.

NOAA weather broadcasts on the weather (WX) channels are

available only in the USA and certain regions in Canada.

Compatible radio models are programmed with 10 WX channels

to monitor weather broadcasts from the National Oceanic and

Atmospheric Organization (NOAA). WX channels are listen-only

channels that broadcast in a continuous loop and are updated

regularly. NOAA broadcasting information is regional and

relevant to your broadcast area.

Tuning Weather Broadcasts

From the home screen, press the ENTER dial.

WX appears on the screen.

Turn the ENTER dial to change the weather channel.

Enabling and Disabling Weather Alerts

You can enable weather (WX) alerts to sound when you are

using standard radio channels.

When tuning weather broadcasts, select ALERT to enable or

disable weather alerts.

indicates that weather alerts are enabled.

Select EXIT.

The radio returns to normal operation while continuing to

monitor weather alerts.

Digital Selective Calling

NOTE: Before you can use DSC capabilities, you must enter a

Mobile Marine Safety Identity (MMSI) number (Entering Your

MMSI Number, page 4). An MMSI number identifies each

DSC radio, like a telephone number.

Digital Selective Calling (DSC) is a key component of the Global

Maritime Distress and Safety System (GMDSS). DSC enables

VHF radios to place and receive digital calls directly with other

vessels and shore stations, including the USA and Canadian

Coast Guards. Your radio includes full Class-D DSC capabilities.

If you have a GPS device connected to the transceiver, your

latitude, longitude, and the current time are transmitted when

you send a distress call or other type of DSC call. If you enter

your position information manually, your latitude, longitude, and

time of entry are transmitted with the call. Transmitting your

location automatically speeds help in an emergency situation.

Channel 70 is reserved exclusively for DSC calls, and your

device uses a dedicated receiver to maintain a constant watch

on Channel 70. You do not need to change the channel to make

a DSC call. Your device changes to Channel 70 automatically to

transmit a DSC call. Your radio sends the DSC data over

Channel 70 in less than one second, and then tunes to an

appropriate channel for voice communications.

appears on the device screen when you have an incoming or

missed DSC call.

NOTE: The device disables DSC automatically when you turn

on ATIS (Automatic Transmitter Identification System,

page 8).

Entering Your MMSI Number

NOTICE

You can enter your MMSI number only once. If you must change

your MMSI number after entering it, you must take your radio to

your Garmin

dealer for reprogramming.

The Mobile Marine Safety Identity (MMSI) number is a nine-digit

code that acts as a DSC self-identification number, and it is

required to use the DSC capabilities of your radio. You can

obtain an MMSI number from the telecommunications authority

or ship registry for your country. In the USA, you can obtain an

MMSI number from these sources:

• Federal Communications Commission (FCC): assignments

are recognized internationally

• BoatU.S.

, Sea Tow

, or United States Power Squadrons

assignments are for USA waters only.

Select MENU > DSC > MY MMSI.

Enter your MMSI number (Entering Text, page 4).

Select ACCEPT.

The radio prompts you to confirm your identity.

Enter your MMSI number again, and select ACCEPT.

If the MMSI numbers you entered do not match, a message

appears.

If necessary, select RETRY, and enter the number again.

Viewing Your MMSI Number

Select MENU > DSC > MY MMSI.

Distress Calls

When you make a distress call, your call is transmitted to all

DSC-capable radios within receiving range. Your current GPS

position (latitude and longitude) and the current time are

included in the transmission if you have a GPS device

connected to your transceiver. If you manually entered your

position information with the time, that data is transmitted with

the call.

NOTE: You should familiarize yourself with the standard

distress-call format and protocol to ensure your calls are clear

and effective.

Sending an Undesignated Distress Call

When you send an undesignated distress call, the nature of your

emergency is not transmitted to the receiving stations. Sending

an undesignated distress call is a faster procedure that can save

you time during an emergency.

Lift the spring-loaded door, and hold DISTRESS for at least 3

seconds.

The radio beeps and counts down the seconds. DISTRESS

CALL COUNTING DOWN appears on the screen.

The radio sounds an alarm, switches to channel 70, and

transmits your call on high (25 W) power.

Press any key to silence the alarm sound.

4 NOAA

Weather Broadcasts and Alerts

The radio tunes to channel 16 on high (25 W) power.

Select PTT on the handset or radio to relay your distress

message.

The radio waits for an acknowledgment (ACK) on channel 70

from a listening station.

Sending a Designated Distress Call

When you send a designated distress call, the nature of your

emergency is transmitted to the receiving stations.

Lift the spring-loaded door, and press DISTRESS.

Turn the ENTER dial, and select the type of distress call.

TIP: You can select CLEAR to exit the screen without

sending a distress call.

Hold DISTRESS for at least three seconds.

The radio beeps and counts down the seconds. DISTRESS

CALL COUNTING DOWN appears on the screen.

The radio sounds an alarm, switches to channel 70, and

transmits your call on high (25 W) power.

Press any key to silence the alarm sound.

The radio tunes to channel 16 on high (25 W) power.

Select PTT on the handset or radio to relay your message.

The radio waits for an acknowledgment (ACK) on channel 70

from a listening station.

Waiting For and Receiving and Acknowledgment for a

Distress Call

If the radio does not receive an acknowledgment for a distress

call, the radio retransmits the distress call randomly between 3.5

to 4.5 minutes later, and continues to retransmit the distress call

at random intervals until the radio receives an acknowledgment.

When the radio receives the acknowledgment, it begins beeping

and DISTRSS ACK appears on the screen.

Press any key to turn off the beeping.

Select to view additional information.

TIP: If the MMSI of the station transmitting the

acknowledgment signal is an entry in your directory, the

name associated with the MMSI number appears on the

screen. If the MMSI of the station is not in your directory, the

MMSI number appears on the screen.

Select ACCEPT.

Pausing and Resuming Distress Call Retransmission

If the radio does not receive an acknowledgment for a distress

call, the radio retransmits the distress call randomly between 3.5

to 4.5 minutes later, and continues to retransmit the distress call

at random intervals until the radio receives an acknowledgment.

You can pause and resume the retransmission countdown.

Send a designated or undesignated distress call.

Select PAUSE.

The distress-call-retransmission countdown stops.

Select an option:

• To resume the countdown, select RESUME.

• To revoke the distress call, select CANCEL (Revoking a

Distress Call, page 5).

Stopping Automatic Retransmission of Distress Calls

Select CANCEL.

The radio remains tuned to channel 16.

NOTE: Selecting CANCEL ends the automatic repetition of

the call, but does not communicate to other stations that you

no longer have an emergency. If you no longer have an

emergency, you should revoke the distress call (Revoking a

Distress Call, page 5).

Revoking a Distress Call

You do not transmit a distress call until you hold DISTRESS for

at least three seconds. If you inadvertently make a distress call,

or are no longer in distress, you should cancel the call

immediately by transmitting a voice message to all stations on

channel 16.

Select CANCEL > YES, and wait until DISTRESS CANCEL

HAS BEEN SENT appears on the screen.

Select OK.

Hold PTT on the handset, and transmit an appropriate voice

message to cancel the distress call (Distress Call

Cancellation Script, page 5).

Select an option:

• Select END to complete the distress-call cancellation and

return to normal radio operation.

• Select RESEND to resend the distress-call cancellation

and start the process again.

Distress Call Cancellation Script

When you revoke a DSC distress call (Revoking a Distress Call,

page 5), you should transmit an appropriate cancellation

message.

For example, "All stations, all stations, all stations, this is

_____(vessel name), MMSI number ____, position ____(North

or South), ____(West or East). Cancel my distress alert of

____(date and time). This is ____(vessel name), MMSI number

____. Out."

Placing Calls

Placing Individual Calls

Select DSC > INDIVIDUAL.

Select an option:

• To enter the MMSI number manually, select MANUAL,

enter the MMSI number, and select ACCEPT.

• To select an entry from the directory, select DIRECTORY,

and select an entry.

• To select a recent call, select RECENT CALLS.

Select a channel (Individual Call or Group Call Channels,

page 6).

The radio transmits the request with your call.

Select CALL.

The radio transmits the call on channel 70, and returns to the

previous channel while listening for an acknowledgment on

channel 70. After an acknowledgment is received, the radio

changes to the channel you selected for the call.

Placing Group Calls

Before you can place a call to a group, you must enter the MMSI

number of the group into the directory (Adding a Group,

page 8).

You can contact a group of specific vessels, such as a sailing

club or flotilla, by making a group call.

Select DSC > GROUP > CALL.

Select a saved group.

Select a channel (Individual Call or Group Call Channels,

page 6).

The radio transmits the channel request with your call.

Select CALL.

The radio transmits the call on channel 70, then changes to

the selected channel.

Placing All-Ships Calls

All-ships calls are transmitted to all stations within receiving

distance of your radio. You can make two types of all-ships

Digital Selective Calling 5

calls. Safety calls broadcast significant navigational or weather-

related information. Urgency calls communicate situations about

the safety of a vessel or person when danger is not imminent.

The captain should discern whether a situation warrants a safety

call or an urgency call.

Select DSC > ALL SHIPS.

Select SAFETY or URGENCY.

Select a channel (Individual Call or Group Call Channels,

page 6).

The radio transmits the channel request with your call.

Select CALL.

The radio transmits the call on channel 70, then changes to

the selected channel.

Individual Call or Group Call Channels

When placing an individual or group call, you should select from

designated DSC channels. The radio transmits this request with

your call.

• USA: channels 6, 8, 9, 10, 13, 17, 67, 68, 69, 71, 72, 73, and

77.

• Canada and International: all USA channels, plus channel 15

DSC channels are limited to channels that are available in all

frequency bands. You can select CUSTOM to select a channel

that is not listed. If you select a custom channel, the station you

are calling may not be able to comply with the specified channel.

You should select a channel that is appropriate for

communication.

Requesting a Vessel's Position

Position data received from stations that respond to position

request calls is sent over the NMEA

network. You can track the

vessels on your Garmin chartplotter.

Select DSC > POS. REQUEST.

Select an option:

• To enter the MMSI number manually, select MANUAL,

enter the MMSI number, and select ACCEPT.

• To select an entry from the directory, select DIRECTORY,

and select an entry.

Select CALL.

The radio transmits the call on channel 70 and returns to the

previous channel. WAITING FOR ACKNOWLEDGE appears

on the screen.

Receiving Calls

Receiving Distress Calls and Distress Relay Calls

When receiving a distress call or a distress relay call,

DISTRESS or DISTR RELAY, and information about the call,

such as MMSI number and the nature of the distress, appear on

the radio screen. A distress call is sent from a vessel in need of

assistance, and a distress relay call is sent from either another

vessel or a station on behalf of a vessel in need of assistance.

The radio sends data related to the call over the NMEA network

based on how you configure MMSI filters (Configuring DSC

NMEA Transmissions, page 9).

NOTE: When a distress call is received, the radio switches to

channel 16 automatically after ten seconds.

When a distress call is received, select an option:

• To view additional information about the distress call and

switch to channel 16, select .

• To accept the distress call and switch to channel 16,

select OK.

• To review information about the distress call without

switching to channel 16 automatically, select PAUSE.

• To ignore the distress call and stay on the current

channel, press CLEAR.

Receiving All-Ships Urgency and Safety Calls

When you receive an all-ships urgency or safety call, ALL

SHIPS appears on the screen, and URGENCY or SAFETY

appears as the type of call. If the channel request is for an

invalid channel, INVALID CH REQUEST appears on the screen.

NOTE: When an all-ships call is received, the radio switches to

the requested channel automatically after ten seconds.

When an urgency or safety call is received, select an option:

• To view additional information about the call and switch to

the requested channel, select .

• To accept the call and switch to the requested channel,

select OK.

• To review information about the call without switching to

the requested channel automatically, select PAUSE.

• To ignore the call and stay on the current channel, press

CLEAR.

Receiving Individual Routine Calls

When you receive an individual routine call, INDIVIDUAL

appears on the screen, and ROUTINE appears as the type of

call. If the channel request is for an invalid channel, INVALID CH

REQUEST appears on the screen.

NOTE: When an individual call is received, the radio switches to

the requested channel automatically after ten seconds.

When a call is received on a valid channel, select an option:

• To accept the call and switch to the requested channel,

select OK.

• To review information about the call without switching to

the requested channel automatically, select PAUSE.

• To ignore the call and stay on the current channel, press

CLEAR.

Receiving Position Requests

You can configure the radio to reply automatically to incoming

position requests, or prompt you to review and approve the

incoming requests before replying (Sending Automatic Replies,

page 8).

When you receive a position request with automatic position

replies enabled, SENDING ACKNOWLEDGE appears on the

screen, and the radio sends your position automatically. After

the position successfully transmits, POSITION SENT appears

on the screen.

When you receive a position request with automatic position

replies disabled, POS. REQUEST appears on the screen.

When you receive a position request with automatic position

replies disabled, select OK, and select an option:

• To reply to the position request with your current position,

select OK.

If GPS-position or manual-position data is available, the

radio transmits your position to the other vessel.

• To ignore the position request, press CLEAR.

Receiving Position Calls

When you receive a position call, POS. SEND and the position

data appear on the screen.

Select OK.

The radio saves the position report in the call log.

Receiving Group Calls

When you receive a group call, GROUP appears on the screen,

and the radio prompts you to change to the requested channel.

If the channel requested is invalid, INVALID CH REQUEST

appears on the screen.

Select OK.

Turn the ENTER dial to select the requested channel.

6 Digital Selective Calling

Select OK.

Position Tracking

When you enable position tracking, the radio uses interval-

based position requests to track up to three vessels.

Your radio transmits received position data over the NMEA

network, and you can track the vessels using your Garmin

chartplotter (Configuring DSC NMEA Transmissions, page 9).

Selecting Vessels and Activating Position Tracking

Before you can use position tracking, you must have at least

one vessel saved in the directory (Directory, page 7).

Select DSC > POS. TRACKING > ADD ENTRY.

Select the vessels you want to track.

You can track the position of up to three vessels at one time.

If you select a fourth vessel, the radio sounds an error tone,

and you must remove a vessel before you can add a new

one.

Select BEGIN TRACKING.

appears on the screen when the radio tracks vessels.

Position-Tracking Polling Interval Sequence

Regulations allow transmission of one position-request call

every five minutes. When tracking more than one vessel, the

radio alternates calling each vessel in the list at five-minute

intervals. If a vessel does not respond to five consecutive

position-request calls, the radio removes the vessel from the

position-tracking list.

You can use this table to better understand how the time interval

is applied to the vessels in the position-tracking list.

Vessel Time

Ship 1 0 minutes (immediately when starting position tracking)

Ship 2 5 minutes

Ship 3 10 minutes

Ship 1 15 minutes

Ship 2 20 minutes

Ship 3 25 minutes

Viewing and Deactivating Vessels on the Position

Tracking List

You can deactivate vessels that you want to keep in the tracking

list, but do not want to actively track.

Select DSC > POS. TRACKING > VESSELS.

Select a vessel.

Select OFF.

Deleting a Vessel From the Position Tracking List

You can delete vessels from the tracking list that you don't plan

to track in the future.

Select DSC > POS. TRACKING > DELETE.

Select a vessel.

Select YES.

Call Log

When the radio receives a DSC call, it records the date and

time, calling station, and type of call in the call log. The radio

also records the latitude and longitude of the calling station if

that data is transmitted with the call.

DSC calls are logged as distress, position, or other calls.

Call Type Call Log

Distress Distress

Distress relay Distress

Distress acknowledge Distress

Call Type Call Log

Position send Position

Position request Position

Group Other

All Ships Other

Individual Other

When you enter a calling station in your directory, the name of

the station appears in the list of calls. If the calling station is not

saved in your directory, the MMSI number appears in the list of

calls. A symbol indicates the station type.

Symbol Meaning MMSI Number Format

Ship station XXXXXXXXX

Group call 0XXXXXXXX

Coastal station 00XXXXXXX

Viewing the Calls in the Call Log

Select DSC > CALL LOG.

Select a call-log category.

Select a call.

Information about the call appears on the screen.

Placing a Call from a Call Log

Calls placed from the call log are placed as individual routine

calls.

Select DSC > CALL LOG.

Select a call log type.

Select the MMSI number or the station name.

Select CALL.

Select a channel on which to transmit the call (Channel Lists,

page 10).

The radio transmits the channel request with your call.

Select CALL.

Saving a Vessel or Station to the Directory from the

Call Log

Select DSC > CALL LOG.

Select a call-log category.

Select the MMSI number you want to save.

Select SAVE.

Enter or edit the name for the saved vessel or station

(optional) (Entering Text, page 4).

Deleting a Call Log Entry

Select DSC.

Select a call-log category.

Select the MMSI number or station.

Select .

Select DELETE.

Directory

You can store the MMSI numbers of vessels and stations, and

assign names to them for quick access or for identification

purposes.

Viewing Saved Vessels and Stations in the Directory

Select DSC > DIRECTORY > DIRECTORY.

Select a saved vessel or station.

Adding an Entry to the Directory

Select DSC > DIRECTORY > ADD ENTRY.

Digital Selective Calling 7

Enter the MMSI number (Entering Text, page 4).

Enter a name (optional).

Select ACCEPT.

Editing an Entry in the Directory

Select DSC > DIRECTORY > EDIT ENTRY.

Select an entry.

Edit the MMSI number, the name, or both (Entering Text,

page 4).

Select ACCEPT.

Deleting an Entry from the Directory

Select DSC > DIRECTORY > DELETE.

Select an entry.

Select YES.

Adding a Group

A DSC group is a collection of specific vessels, such as a sailing

club or flotilla, that share a single group MMSI number.

Select DSC > GROUP > ADD ENTRY.

Enter the group MMSI number (Entering Text, page 4).

Enter a name for the group (optional).

Select ACCEPT.

Editing a Group

Select DSC > GROUP > EDIT ENTRY.

Select a group.

Edit the group MMSI number, the name, or both (Entering

Text, page 4).

Select ACCEPT.

Deleting a Group

Select DSC > GROUP > DELETE.

Select a group.

Select YES.

DSC Settings

Manual Position Information

If you do not have a GPS device connected to your radio, you

can manually enter your position and time of entry. The position

data is transmitted with DSC calls. When you enter the position

and time manually, MANUAL POS appears on the screen.

Manually entered position information must be updated

regularly, and the radio displays two alerts to remind you to

update the position data.

• When the position data you entered manually is more than

four hours old, DATA IS OVER 4 HOURS OLD appears on

the screen. The radio continues to transmit this position data,

but you should update it before it becomes invalid.

• When the position data you entered manually is more than

23.5 hours old, it is considered invalid and DATA IS INVALID

appears on the screen. The radio does not transmit invalid

position data, and you should update it immediately.

Entering Position Information Manually

Select MENU > SYSTEM > MANUAL GPS.

Enter your current coordinates and the present time (Entering

Text, page 4).

Select ACCEPT.

Changing the Channel to 16 Automatically

By default, the radio changes to channel 16 automatically when

receiving distress, distress relay, and all-ships urgency calls. In

certain situations, when you must continually monitor a channel

to maintain uninterrupted communication with another vessel,

for example, you can disable this feature.

Select MENU > DSC > AUTO CHANGE CH..

Select an option:

• To set the radio to switch automatically to channel 16

when you receive a qualifying call, select ON.

• To set the radio to prompt you to accept or decline a

channel change when you receive a qualifying call, select

OFF.

Sending Automatic Replies

You can configure the radio to automatically respond to

incoming calls, including position requests.

NOTE: When you configure the radio to automatically respond

to incoming calls, the radio also changes the channel

automatically for all incoming individual calls.

Select MENU > DSC > INDIV REPLY.

Select an option:

• To send automatic replies, select AUTO.

• To send replies manually, select MANUAL.

Automatic Transmitter Identification

System

Automatic Transmitter Identification System (ATIS) is a vessel

identification system used on certain inland waterways in some

European countries. See your Garmin dealer to program your

VHF radio if you plan to use your radio on waterways that are

within the bounds of the Regional Arrangement Concerning the

Radiotelephone Service on Inland Waterways (the Basel

Agreement). ATIS is prohibited outside the European inland

waterways that are covered by the Basel Agreement.

When you enable ATIS, your radio sends a data signal

identifying your station at the end of every transmission. Data

identifying your position is not sent, but your position is

calculated through the method of triangulation by coastal

stations that receive your transmissions.

To enable ATIS, you must enter your ATIS identification number

(Entering Your ATIS Identification Number, page 8), and turn

on ATIS (Turning On and Off ATIS, page 9). See your Garmin

dealer to determine your ATIS identification number and to learn

about ATIS requirements for your region.

Your radio disables these functions when you enable ATIS.

• Digital Selective Calling (DSC)

• Monitor two or three channels (Dual watch and Tri watch)

• Scanning channels

International channels 6, 8, 10, 11, 12, 13, 14, 71, 72, 74, and

77 restrict transmitting to low-power (1 W) when you enable

ATIS.

Entering Your ATIS Identification Number

NOTICE

You can enter your ATIS identification number only once. If you

must change your ATIS identification number after entering it,

you must take your radio to your Garmin dealer for

reprogramming.

NOTE: You can access the ATIS settings on the radio after the

ATIS feature is activated by your Garmin dealer.

Select MENU > ATIS > MY ATIS ID.

Enter your ATIS number (Entering Text, page 4).

Select ACCEPT.

The radio prompts you to reenter your number.

Enter your ATIS number again, and select ACCEPT.

If the ATIS numbers do not match, a message appears.

If necessary, select RETRY, and enter the number again.

8 Automatic Transmitter Identification System

Turning On and Off ATIS

Select MENU > ATIS > ATIS.

Select ON or OFF.

appears on the screen when ATIS is enabled.

Select OK.

Viewing Your ATIS Identification Number

Select MENU > ATIS > MY ATIS ID.

NMEA 0183 and NMEA 2000

When you connect the radio to a NMEA 0183 device or a NMEA

2000 network, you can transfer received DSC distress and

position information to any compatible connected chartplotter

(NMEA, page 10).

The radio can also receive GPS-position information from a

NMEA 0183 device or a NMEA 2000 network. Received GPS-

position information appears on the home screen and is

transmitted with DSC calls. appears on the screen when GPS

data is available, and flashes when GPS data is not present.

When GPS data is not present, you must enter your position

manually (Manual Position Information, page 8).

For more information on connecting the radio to a NMEA 0183

device or a NMEA 2000 network, see the VHF 315 Series

Installation Instructions.

Additional Functionality with Other Garmin

Devices

The radio has additional capabilities when you connect it to

other Garmin devices, such as a chartplotter.

NOTE: You may need to upgrade your Garmin chartplotter

software to use NMEA 0183 or NMEA 2000 features.

When you connect the radio to a Garmin chartplotter using

either NMEA 0183 or NMEA 2000, your chartplotter keeps track

of the current and previous positions of the contacts in the

directory.

When you connect the radio to the same NMEA 2000 network

as a Garmin chartplotter, you can use the chartplotter to set up

an individual routine call.

When you connect the radio to the same NMEA 2000 network

as a Garmin chartplotter, and you initiate a man-overboard

distress call from the radio, the chartplotter prompts you to

navigate to the man-overboard location. If you connect a Garmin

autopilot system to the same NMEA 2000 network, the

chartplotter prompts you to start a Williamson's turn to the man-

overboard location.

Communicating Over NMEA 0183 or NMEA

2000

NOTE: This feature is not available on all models.

You can select a connection either to a NMEA 0183 device or to

a NMEA 2000 network. The radio can communicate over only

one communication protocol at a time.

Select MENU > COMMUNICATIONS > PROTOCOL.

Select NMEA0183 or NMEA2000.

Configuring DSC NMEA Transmissions

You can filter the types of DSC-call data the radio sends to a

connected NMEA 0183 device or over a NMEA 2000 network.

Select MENU > COMMUNICATIONS > DSC OUTPUT.

Select an option:

• To send NMEA data when you receive a DSC call from

any MMSI number, select ALL VESSELS, and proceed to

the last step.

• To disable sending NMEA data when you receive a DSC

call, select NO VESSELS, and proceed to the last step.

• To send NMEA data only when you receive a call from a

vessel in your directory, select SELECT VESSELS, and

proceed to the next step.

NOTE: When you configure the radio for SELECT

VESSELS, all received DSC-distress-call data is sent over

NMEA, even if the vessel is not in your directory.

Select a vessel in your directory.

Select an option:

• To send all DSC-call data from this vessel, select ON.

• To send DSC-distress-call data only from this vessel,

select OFF.

Repeat this process for each vessel in your directory.

Select BACK to save your changes and exit the menu.

System Settings

Select MENU > SYSTEM.

DISPLAY: Sets the backlight and contrast levels.

BEEPER: Sets the volume or disables the beeper tone that

sounds when you press a key or turn a dial.

AUTO POWER-ON: Sets the radio to turn on automatically

when it receives power.

LANGUAGE: Sets the language for the radio.

Number Settings

You can customize the numbers shown on the home screen of

the radio.

Select MENU > SYSTEM > NUMBERS.

LAT/LONG: Shows or hides the latitude and longitude numbers

from either a connected GPS device, or from manually

entered position data.

TIME: Shows or hides the time received from a connected GPS

device or entered manually.

NOTE: The time updates automatically only if you connect a

GPS device. When you enter your time and position

manually, the time shown does not update automatically. For

manually entered position and time data, the time of entry is

always shown on the home screen, even if you hide the time

with this setting.

COG/SOG: Shows or hides course-over-ground (COG) and

speed-over-ground (SOG) information.

NOTE: You must connect a GPS device to show course-

over-ground (COG) and speed-over-ground (SOG)

information.

Units Settings

You can set the unit of measure used for values shown on the

radio.

Select MENU > SYSTEM > UNITS.

SPEED: Sets the unit of measure shown for speed-related

fields, such as speed-over-ground.

TIME > FORMAT: Sets the time format.

HEADING: Sets the radio to show all heading calculations, such

as Course Over Ground (COG), using true or magnetic north.

NOTE: If the radio is configured for NMEA 2000

communication, the heading unit is set to AUTO, and shows

heading data based on the information provided over the

network. This setting cannot be changed.

NMEA 0183 and NMEA 2000

Configuring the Time Offset

You can show the local time rather than Universal Coordinated

Time (UTC). When you adjust for local time, LOC appears after

the time on the home screen.

NOTE: When you make a DSC call, the time is sent in UTC

format.

Select MENU > SYSTEM > UNITS > TIME > OFFSET.

Turn the ENTER dial to adjust the time offset from UTC.

Select OK.

Selecting the Frequency Band

You can switch between the USA, International, or Canadian

frequency bands (Channel Lists, page 10).

NOTE: Not all frequency bands are available on all device

models.

Select MENU > CHANNEL > FREQUENCY BAND.

Select a frequency band.

Changing a Channel Name

Channel names appear on the home screen using nine

characters. If a channel name is longer than nine characters, the

full name scrolls across the top of the screen, then switches to

the short name. You can change the name of a channel to

reflect a local meaning.

Select MENU > CHANNEL > NAME.

Turn the ENTER dial to select a channel, and select OK.

Change the name of the channel (Entering Text, page 4).

Select ACCEPT.

Restoring Factory Settings

You can restore the radio to the default factory settings. When

you restore the radio to factory settings, all system changes and

customizations are lost. Restoring factory settings deletes the

call logs, but retains group entries, directory entries, the MMSI

number, and the ATIS ID.

Select MENU > SYSTEM > SYSTEM INFO > RESET.

Select YES to confirm the reset.

Appendix

Alarms and Messages

BATTERY ALRM: Sounds when the battery reaches a specified

low or high voltage. Check the battery wiring.

WX: Sounds when you set a weather alarm and the radio

detects an incoming weather alert (NOAA

Weather

Broadcasts and Alerts, page 4). The radio tunes

automatically to the weather channel that is broadcasting the

alert.

GPS ALARM: Sounds first when GPS data from a NMEA

network or position data entered manually is more than four

hours old. Sounds again when GPS data from a NMEA

network or position data entered manually is more than 23.5

hours old (Manual Position Information, page 8).

POSITION TRACKING: Appears after five consecutive failed

attempts to request position information from a vessel

(Position Tracking, page 7).

Channel Lists

The International, USA, and Canadian channel lists are

available online for reference. You are responsible for the

correct use of channels according to local regulations.

• To view the latest international channel list, go to

www.navcen.uscg.gov/?pageName=apps18.

• To view the latest USA channel list, go to

www.navcen.uscg.gov/?pageName=mtVhf.

• To view the latest Canadian channel list, go to www.ic.gc.ca

/eic/site/smt-gst.nsf/eng/sf01011.html#sched1.

VHF 315 Series Specifications

Dimensions (H x W x D) 6 x 20.5 x 18.1 cm (2.36 x 8.07 x 7.13 in.)

Weight 1.527 kg (3.37 lb.)

Temperature range Operating: From -15° to 70°C (from 5° to

158°F)

Storage: From -20° to 70°C (from -4° to

158°F)

Compass-safe distance 50 mm (2 in.)

Water rating* IEC 605290 IPX7

Antenna connector S0-239 (50 ohm)

Operating voltage 12.0 Vdc

Current draw Standby: 350 mA

Receive: 600 mA

Transmit: From 2.0 A to 6.0 A (from 1 W to

25 W)

Maximum antenna gain 9 dBi

Antenna port impedance 50 ohm

Hailer output power 20 W at 4 ohm

Hailer horn impedance 4 ohm

NMEA 2000 LEN 1 (50 mA)

*The device withstands incidental exposure to water of up to 1 m

for up to 30 min. For more information, go to www.garmin.com

/waterrating.

NMEA

NMEA 0183 IN Sentences Supported

Sentence Definition

GGA Global positioning system fix data

GLL Geographic position (latitude/longitude)

GNS GNSS fix data

RMA Recommended minimum specific Loran-C data

RMB Recommended minimum navigation information

RMC Recommended minimum specific GNSS data

NMEA 0183 OUT Sentences Supported

Sentence Definition

DSC DSC information

DSE Expanded DSC

NMEA 2000 PGN Information

Receive Transmit

059392 ISO acknowledgment 059392 ISO acknowledgment

059904 ISO request 060928 ISO address claim

060928 ISO address claim 126208 NMEA request/

command/ack

126208 NMEA request/

command/ack

126464 PGN list

129026 COG/SOG, rapid update 126996 Product information

129029 GNSS position data 129799 Radio frequency/mode/

power

129808 DSC call information

Transmit (AIS models only)

129038 Class A position report

129039 Class B position report

10 Appendix

Transmit (AIS models only)

129040 Class B extended position report

129794 AIS class A static and voyage

related data

129798 AIS SAR aircraft position report

129802 AIS broadcast safety message

129809 AIS class B static data part A

129810 AIS class B static data part B

Cleaning the Outer Casing

NOTICE

Avoid chemical cleaners and solvents that can damage plastic

components.

Clean the outer casing of the device (not the screen) using a

cloth dampened with a mild detergent solution.

Wipe the device dry.

Appendix 11

Index

alarms 10

automatic transmitter identification system 8, 9

backlight 9

beeper 9

call log 7

channels 2, 10

16/9 3

16+ 3

Canada 6

International 6

monitoring 2

power 3

priority 2

saving 2

scanning 2

transmitting 3

USA 6

chartplotter 9

contrast 9

device, cleaning 11

digital selective calling 4, 6, 7

settings 8

directory 7, 8

distress calls 4–6

canceling 5

revoking 5

DSC. See digital selective calling

dual watch 2

factory settings 10

foghorn 3

group calling 5, 6, 8

hailer horn 3

home screen 1

customizing 9

icons 1

keys 1

power 1

MMSI 4

networking 9

NMEA 0183 9, 10

NMEA 2000 9, 10

placing calls 5

all ships 5

position 8

request 6

tracking 7

position request 8

power 3

receiver, sensitivity 3

receiving calls 6, 8

safety call 5

settings 2, 9, 10

squelch 1

system information 1

system settings 9

text, entering 4

time

setting 10

zone 10

tri watch 2

units of measure 9

urgency call 5

VHF radio

individual routine call 2

transmitting 3

volume, adjusting 1, 9

weather

broadcasts 4

messages 4

12 Index

support.garmin.com

May 2018

190-02416-00_0A

Garmin VHF 315 serie Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Garmin VHF 315 serie

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info