Handleiding Garmin TR-1 Gladiator (pagina 12 van 36) (Engels)

583791

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

The Man Overboard (MOB) function causes the boat to turn to port until the reciprocal

course is established, with the goal of running alongside the point where the Plus button

was pushed, The boat path will be as shown in the  gure below. The pilot will return to

heading hold if either of the Right Arrow, Left Arrow, or Plus buttons are pressed.

Code 14: The Man overboard maneuver can be tuned to run close to the object or point

at any given speed, but may miss at another speed. You should probably adjust the maneuver at a speed that is

below planing speed. If the object or point passes on your starboard reduce code 14.

You are responsible as the captain of your boat to use the MOB feature in a manner as to not cause harm to any

person or property. Be aware of any objects in the water before pressing the MOB button. The MOB feature is

not set by GPS. Due to wind, waves and current your boat may not return to the exact reciprocal course when

the MOB button is pressed.

The autopilot will attempt to perform any of its steering functions when the boat is backing in

reverse gear. To engage the system in reverse: 1) Start from Standby. 2) Press and hold the GPS

(REV) button. 3) Press and release the Auto/Stby button. 4) Release the GPS (REV) button.

The Man Overboard (MOB) function causes the boat to turn to starboard for a while then turn to

port until the reciprocal course is established, with the goal of running alongside the point where

the MOB button was pushed. The boat path will be as shown in the figure below.

Changing Heading With MOB

Reverse

If you program the Bent Right Arrow and Bent Left Arrow buttons for Circles, pressing the

Bent Right Arrow button will cause your boat to be driven in a clockwise (from above) circle

with a lap time between 1 and 90 minutes (programmable). The Bent Left Arrow button will

cause counterclockwise turns. You can exit the circle and run straight anytime by pressing either

the Straight Right Arrow or Straight Left Arrow button.

Circles

If you program the Bent Right Arrow and Bent Left Arrow buttons for Steps, when one

of these buttons is pushed, the pilot will execute a port or starboard turn. The turn will

terminate when the programmed step angle is reached. The step angles are programmable

from 1 to 90 degrees. Multiple pushes of these buttons will result in a turn through an angle

equal to the sum of the angles per push. For example, if you have programmed the pilot for 10

degree steps, five pushes of the Bent Right Arrow button will turn you 50 degrees to starboard.

180 degrees is the maximum turn sum.

Step Turns

Change Heading Using Man Overboard

Description Code

Range of Settings

Factory Setting

MOB Overshoot Code

1 most overshoot command, 40 most under shoot command

Code 14: The Man overboard maneuver can be tuned to run over or close to the object or point at any given

speed, but may miss at another speed. You should probably adjust the maneuver at a speed that is below

planing speed. If the object or point passes on your starboard reduce code 14.

To change the settings for Man

Overboard:

1. Press and release the [Setup]

Button. The [Setup] LED will

illuminate to indicate the system

is ready to take setup commands

(button pushes).

3. Select and enter code 14 by

pressing and releasing the buttons

labeled 1 & 4 (14) until the

appropriate LED’s are lit. (See the

Code and Setup Choice on the table below.

4. Increase an adjustable parameter one step by each press of the [UP Arrow] button. When the parameter

is adjusted to its maximum value, the [Up Arrow] LED will light. The parameter is adjusted and is in use by

the autopilot immediately.

5. Decrease an adjustable parameter one step by each press of the [Down Arrow] button. When the

parameter is adjusted to its minimum value, the [Down Arrow] LED will light. The parameter is adjusted

and is in use by the autopilot immediately.

6. To

save the changes into permanent memory and

make the selected function into a startup

default: Press and release the [Setup] button (the [Setup] LED should be lit), and then

press and hold the [Select Load] button. While holding down the [Select Load] button,

press and release the [Deckmount] On/Off button quickly, then release the GPS [Select

Load] button.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Garmin TR-1 Gladiator Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info