801309
15
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
Installing the Transducer on a Pole
You can use the included hardware to install the transducer on a pole (not included). Installing the transducer
on a pole is similar to installing the transducer on a trolling motor shaft. If needed, you can refer to the
diagram provided for installing the transducer on a trolling motor shaft when installing the transducer on a pole
(Installing the Transducer on the Trolling Motor Shaft, page11).
NOTE: You can use the included flat bracket for mounting the transducer on a pole.
Labels identifying the parts bags required for this procedure:
NOTICE
You must secure the transducer cable to the pole or other secure location during installation. Damage to the
transducer cable wire or the cable jacket can cause transducer failure.
1Remove the back of the pole-mount bracket and four screws from parts bag .
2Remove the front half of the pole-mount bracket from parts bag .
3If the pole is equal to or less than 25mm (1in.) in diameter, remove the rubber liner from parts bag .
4If the pole is equal to or less than 25mm (1in.) in diameter, wrap the rubber liner around the pole in the
location you want to install the mount.
5Place the pole-mount bracket around the rubber liner on the pole.
6Insert the screws into the pole-mount bracket, and secure them using the M6 hex wrench in parts bag .
7Remove the knob from parts bag .
8Place the transducer against the pole-mount bracket, and secure it using the knob.
NOTE: You can secure the transducer to the mount using the included low-profile hardware instead of the
knob if you do not plan to switch transducer modes frequently during use (Installing the Transducer Using
Low Profile Mounting Hardware, page14).
9Secure the transducer cable to the pole or other secure location, and route the cable to the location of the
sonar module.
Mounting the GLS 10 Black Box Device
NOTICE
If you are mounting the device in fiberglass, when drilling the pilot holes, use a countersink bit to drill a
clearance counterbore through only the top gel-coat layer. This will help to avoid cracking in the gel-coat layer
when the screws are tightened.
NOTE: Screws are included with the device, but they may not be suitable for the mounting surface.
Before you mount the device, you must select a mounting location, and determine what screws and other
mounting hardware are needed for the surface.
1Place the black box device in the mounting location, and mark the location of the pilot holes.
2Drill a pilot hole for one corner of the device.
3Loosely fasten the device to the mounting surface with one corner, and examine the other three pilot-hole
marks.
4Mark new pilot-hole locations if necessary, and remove the device from the mounting surface.
5Drill the remaining pilot holes.
6Secure the device to the mounting location.
15
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin LIVESCOPE XR LVS62 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin LIVESCOPE XR LVS62 in de taal/talen: Engels als bijlage per email.

De handleiding is 4.09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Garmin LIVESCOPE XR LVS62

Garmin LIVESCOPE XR LVS62 Installatiehandleiding - Nederlands - 22 pagina's

Garmin LIVESCOPE XR LVS62 Installatiehandleiding - Deutsch - 22 pagina's

Garmin LIVESCOPE XR LVS62 Installatiehandleiding - Français - 22 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info