579857
78
Verklein
Vergroot
Pagina terug
1/412
Pagina verder
GTN 6XX/7XX AML STC Installation Manual 190-01007-A3
Page 2-36 Rev. 4
2.4.11.4 Shield Termination Consideration
Shield termination at non-Garmin equipment end must be as short as possible and not to exceed 3.0”
taking into consideration any non-Garmin equipment’s installation requirements. When there are no
requirements given by the non-Garmin equipment installation manual, then the shields may be connected
to the metal connector backshell when the backshell is grounded to airframe chassis ground. Alternately,
the shield termination may be directly connected to airframe chassis ground. Although the interconnects
in Appendix E do not show intermediate connectors, all shields must have continuity at any intermediate
connectors used unless otherwise specified. When shields are terminated to the aircraft ground or metal
backshell to provide this continuity, the shield drain wire must be no longer than 3 inches, unless non-
Garmin equipment requires shorter length. The termination method from Section 3.6.3.1 may be used at
these locations unless this conflicts with the requirement of non-Garmin equipment.
If intermediate connectors are used on an audio line, run the shields through a pin on all intermediate
connectors. Audio line shields should be continuous from end to end and be grounded only at one end to
prevent ground loops. See Section 2.4.12.
Shield splicing should be done at the GTN end close to the connector, similar to other non-spliced shields,
unless this conflicts with requirements from remote-end equipment. Honeywell equipment with EMI
backshells (e.g. 360 degree circular connectors, backshells with shields terminated inside a metal
backshell) require the shields to be terminated at the remote end from the GTN utilizing the EMI
backshell.
If a wire from the GTN connector goes to a connector at the remote end that includes overbraided wires
then the new wiring added at the remote end connector must also be overbraided. Any wires spliced into
this wire must also be overbraided. If the wiring passes through bulkhead connectors then each segment
shall be overbraided and the overbraid must be grounded at both ends, unless otherwise shown in the
remote equipment’s installation manual. The overbraid must be terminated as close to the connector as
possible taking into account any requirements imposed by the non-Garmin equipment. These additional
wires must be separately overbraided and ensure they are routed with the existing cable where possible.
The overbraid shall have a minimum of 90% optical coverage.
2.4.11.5 GTN Cooling Requirements
The GTN unit meets all TSO requirements without external cooling. However, as with all electronic
equipment, lower operating temperatures extend equipment life. Reducing the operating temperature may
reduce the mean time between failures (MTBF).
Units tightly packed in the avionics stack heat each other through radiation, convection, and sometimes
by direct conduction. Even a single unit operates at a much higher temperature in still air than in moving
air. Fans or some other means of moving the air around electronic equipment are usually a worthwhile
investment.
The GTN has a cooling fan integrated into the backplate to draw forced-air cooling through the unit.
There are inlets along the left, right, and bottom sides of the GTN bezel that allow air to flow through the
unit. Ensure that there are no obstructions to the air inlets or fan exhaust. Airflow should be unrestricted
from the bezel inlets to the fan outlet in the backplate on the rear of the unit.
2.4.11.6 GMA 35 Cooling Requirements
The GMA 35 does not have provisions for attaching cooling air and does not generate an excessive
amount of heat during typical operations, however the thermal characteristics of the installation should
always be assessed. An undesirable thermal condition could be created due to the unit's own internal
power dissipation combined with restricted ventilation, or due to heat generated by adjacent equipment.
Limiting thermal build up, by means of an external fan or natural convection is always a good practice
and is recommended to increase the product life.
78

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin GTN 650 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin GTN 650 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info