584001
45
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
400 SERIES INSTALLATION MANUAL Page 4-9
P/N 190-00140-02 Page Rev L
4.5 ANNUNCIATORS/SWITCHES
4.5.1 Annunciators/Switches Function
NOTE
Initial certification of the 400 Series units was accomplished without use of any remote switches or
annunciators, since the same switching and annunciation is available on the front panel of the 400
Series unit. However, if the 400 Series unit is not installed in the pilot’s normal field of view, some or all
of the remote switches and annunciators may be required by your certification agency. Appendix B
includes an FAA letter granting permission to install GNS 430 without external switches and annunciators.
4.5.1.1 MESSAGE ANNUNCIATE
When a new status message is available, the Message Annunciator flashes. When status messages remain
effective, the Message Annunciator illuminates.
4.5.1.2 WAYPOINT ANNUNCIATE
The waypoint annunciator output is driven in the following manner:
1. When the aircraft is within 10 seconds of reaching the turning point for a course change, the
waypoint annunciator flashes.
2. When the aircraft is in a turn, the waypoint annunciator illuminates and remains illuminated until
the turn is completed.
3. When a user arrival alarm is set and the aircraft is within the circle defined by the arrival alarm
radius at the arrival waypoint, the waypoint annunciator flashes for 10 seconds.
4. When a user arrival alarm is not set and the aircraft is within 10 seconds of reaching the arrival
waypoint, the waypoint annunciator flashes.
4.5.1.3 CDI SOURCE SELECT (GNS 430 Only)
This discrete input may be used to toggle between display of GPS and VOR/LOC/Glideslope information
on the MAIN external CDI/HSI. A momentary low on this pin performs the same function as pressing the
‘CDI’ key on the GNS 430 bezel.
4.5.1.4 VLOC ANNUNCIATE (GNS 430 Only)
This annunciator output is driven when the unit is configured with a single CDI/HSI and the VOR/ILS data
is being displayed on the CDI/HSI. This output parallels the VLOC annunciator on the display.
4.5.1.5 GPS ANNUNCIATE (GNS 430 Only)
This annunciator output is driven when the unit is configured with a single CDI/HSI and the GPS data is
being displayed on the CDI/HSI. This output parallels the GPS annunciation on the display.
4.5.1.6 OBS MODE SELECT
This discrete input may be used to toggle between GPS OBS and GPS AUTO modes of operation. A
momentary low on this pin performs the same function as pressing the ‘OBS’ key on the 400 Series unit.
4.5.1.7 AUTO ANNUNCIATE
This annunciator output is driven to indicate GPS AUTO mode of operation. This output is active when
neither the OBS nor SUSP annunciations are on the display.
4.5.1.8 OBS ANNUNCIATE
This annunciator output is driven to indicate GPS OBS mode of operation. This output is active when the
OBS or SUSP annunciation is on the display.
4.5.1.9 TERMINAL ANNUNCIATE
When performing approach navigation, the terminal annunciator is illuminated when operating within 30
nautical miles of the departure or arrival airport and the CDI scale is the equivalent or 1.0 nm or less.
4.5.1.10 APPROACH ANNUNCIATE
When performing approach navigation, the approach annunciator illuminates when approach is active.
4.5.1.11 INTEGRITY ANNUNCIATE
The integrity annunciator illuminates when the GPS receiver detects a position error, or is unable to
calculate the integrity of the position.
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin GNS 430 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin GNS 430 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info