Handleiding Gaggia Syncrony Compact (pagina 16 van 61) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans)

3590

Verklein

Vergroot

Pagina terug

1/61

Pagina verder

ENGLISHENGLISH

• 31 •• 30 •

touching directly with your hands.

When the appliance is ready to dispense coffee,

press the button (25), the LEDs (23) and (24)

switch off. The appliance goes through a

preheating period; during this phase, the LED

(25) flashes.

• Before dispensing steam, wait for the green

temperature-ready LED (25) to light up in a

fixed way; this indicates that the correct ope-

rative temperature has been reached.

• Direct the steam nozzle (14) towards the drip

tray and turn the “hot water/steam” knob (16)

for a few seconds so that any residual water

comes out of the steam nozzle. Continue until

only steam is dispensed.

• Turn the knob (16) to OFF.

• Fill 1/3 of the vessel that you wish to use to

make cappuccino with cold milk.

For best results when making

cappuccinos, the milk and the used

cup should be cold.

• Immerse the steam nozzle into the milk to be

frothed and turn the knob (16); turn the

container slowly with up-down movements to

make uniform frothing (Fig.16).

• After using the steam for the desired time, shut

off the steam (16).

• The same system can be used to heat other

beverages.

• Clean the steam nozzle with a damp cloth

(Fig.17)

9.1 Making coffee after using the

steam function

• If you want to make more coffee immediately

after steaming milk, you must press the button

again (25).

• During the transition period, the LEDs (23),

(24) and (25) flash at the same time indicating

that the appliance is superheated and cannot

make coffee.

• To make coffee, you must drain the water by

turning the steam knob (16) until only the tem-

perature-ready LEDs (23) and (24) remain lit

in a fixed way.

10 CLEANING AND MAINTE-

NANCE

General Cleaning

• Maintenance and cleaning should only be

carried out when the appliance is cold and

disconnected from the power supply.

• Do not immerse the appliance in water and

do not wash the parts in the dishwasher.

• Do not use abrasives or aggressive chemicals

(solvents) for cleaning.

• Do not dry the machine and/or any of its

parts using a microwave and/or conventional

oven.

• We recommend you clean the water tank and

change the water daily.

• Clean the ground coffee doser daily.

- Use the supplied brush to clean the doser

(Fig.18).

• To clean the appliance, use a soft cloth

dampened with water (Fig.19).

•Clean the service area and the coffee

dispenser.

• We recommend you empty and clean the drip

tray (12) and the coffee grounds drawer (10)

daily; to carry out this operation you must open

the front cover (Fig.20) and remove the drip

tray (Fig.21); then, you can empty and clean

all the components.

• You can remove the coffee dispenser in order

to clean it (Fig.24):

- lower the dispensing unit nozzles

- take the dispensing unit as shown in Fig. 24,

and remove it from its housing

- wash the whole unit with warm water.

10.1 The coffee disperser

The coffee dispenser (17) must be

cleaned each time you fill the coffee

bean container or, anyhow, at least once a

week.

• Switch off the appliance by pressing the ON/

OFF switch (7) to the “O” position and remove

the plug from the wall outlet.

• Open the service cover (15). Remove the drip

tray (12) and the coffee grounds drawer.

• Remove the coffee dispenser by holding it

by its handle and pressing the “PUSH”

button (Fig.22)

• Make sure that the two steel filters are free

from any coffee residues. The top filter can

be removed by unscrewing the plastic pin

anticlockwise using the specific supplied key

(Fig.23.).

• Wash the coffee dispenser only with hot water:

do not use detergents. Then accurately wash

and dry all its components.

• Refit the filter and carefully screw the plastic

pin back on using the specific key.

• Clean the compartment inside the appliance.

• Holding it by its handle, insert the coffee

dispenser into its housing until it snaps into

place.

• Insert the coffee grounds drawer, the drip tray

plate and the drip tray.

• Close the cover (15).

11 DESCALING

Scaling occurs naturally when the appliance is

used. Approximately every 3-4 months you

should descale it; it is ready for descaling when

you notice a reduction in the water flow or when

the LED of the button (26) flashes.

If you wish to carry this out at home,

you can use a descaling product for

coffee makers that is non toxic and/or not

harmful and commonly available on the

market.

Caution! Never use vinegar.

To descale the appliance proceed as follows:

• Mix the descaler with water as specified on

the package and fill the water tank.

• Switch ON the appliance with the ON/OFF

switch (7).

• Press the button (26) for at least 5 seconds to

select the descaling operating mode; the LED

emits a fixed light.

• Direct the steam nozzle (14) toward the drip

tray.

• Position a vessel of adequate capacity under

the steam nozzle and turn the hot water knob

anticlockwise (16). The appliance starts an

automatic descaling cycle with pauses preset

by the manufacturer and managed

automatically by the appliance.

• At the end of the cycle, the flow of the

descaling solution is shut off and the 5 buttons

start flashing simultaneously.

• Turn the knob of the hot water nozzle (16)

clockwise to OFF. In this case, also the warning

light (27) flashes.

• Rinse the water tank and fill it with fresh

drinking water.

• Position a vessel of adequate capacity under

the steam nozzle and empty 2/3 of the

contents of the water tank by turning the steam

knob (16) anticlockwise; to shut off the flow,

turn the knob (16) clockwise.

• Let the appliance heat up and empty the

remaining contents of the water tank by turning

the steam knob (16) anticlockwise; to stop the

flow, turn it clockwise.

If you use a different product from

the recommended one, we

recommend you follow the instructions of

the descaler manufacturer as specified on

the package.

If the descaling cycle is interrupted

by switching the machine OFF, this is

restarted when the machine is switched back

ON.

12 FUNCTION PROGRAMMING

The appliance allows you to programme some

parameters depending on your needs.

To programme the functions, you must enter

programming mode as follows:

• Ensure that the ON/OFF switch (7) of the

appliance is switched to “O” and that the hot

water knob (16) is OFF.

• Press the buttons (23) and (25) and, at the

same time, switch ON the appliance using

the ON/OFF switch (7).

You are now in the programming mode.

To quit the programming mode and

implement your changes, switch the machine

OFF and, then, back ON again using the

main switch (7).

Gaggia-Syncrony-cod 165892000 rev.01.PMD 14/06/2002, 17.2530-31

Gaggia Syncrony Compact Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Gaggia Syncrony Compact

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info