670447
15
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
FALCON 2 PRO
Quadcopter Drone with Video Camera
User’s Guide for Model DRC377 v1871-01
Warnings & Precautions
Important Safety Instructions
Read and follow all instructions.
Keep these instructions for future reference.
Heed all Warnings.
Intended for children ages 14 and higher. Adult
supervision is required.
Only use attachments/accessories specied by the
manufacturer.
Before ying, always check the body, rotors, and
battery for any damage or obstructions.
Battery should be free from cracks or swelling.
Keep the rotors clear of any obstructions and body
parts to avoid potential damage and injury.
Manufacturer and dealer assume no liability for
accidental damages from improper use or installation
of parts, or from damage incurred from worn or
broken parts.
Pilots are responsible for their actions and any
damage caused from improper use.
Pilots should keep the craft in sight at all times
during ight. If you lose sight of the craft at any time,
power down and cease ight immediately.
Only y in large, open areas that are free from
obstacles or potential hazards, such as trees, power
lines, ceiling fans, and the like.
Flying over bodies of water is not recommended.
Flying at night is not recommended.
Never try to retrieve the craft from areas you cannot
safely reach, such as rooftops or trees.
Never launch the craft from your hand.
Never leave the craft unattended while it is powered
on or while the battery is charging.
FCC Warnings
Warning: Changes or modications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Additional Warnings & Precautions
WARNING: To reduce the risk of re or electric
shock, do not expose this apparatus to rain, moisture,
dripping, or splashing.
CAUTION: Use of controls or adjustments or
performance of procedures other than those specied
may result in personal injury.
WARNING: Changes or modications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
CAUTION: Danger of explosion if battery is
incorrectly replaced. Replace only with the same or
equivalent type.
Lithium batteries, like all rechargeable batteries, are
recyclable and should be recycled or disposed of
according to state and local guidelines. They should
never be disposed of in normal household waste,
and they should never be incinerated, as they might
explode. Contact your local government for disposal
or recycling practices in your area.
WARNING: Shock hazard - Do Not Open.
Battery shall not be exposed to excessive heat such as
sunshine, re, or the like.
Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away from children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
Do not mix old and new batteries.
Completely replace all old batteries with new ones.
Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
Batteries should be recycled or disposed of as per
state and local guidelines.
WARNING: This product may contain chemicals
known to the State of California to cause birth
defects, or other reproductive harm (California Prop
65). Wash hands after handling.
This product meets and complies with all Federal
regulations.
4
Table of Contents
Falcon 2 Pro Quadcopter Drone – 5
Features
Includes
Overview – 6
Craft Layout & Features
Assembly – 7
Landing Struts
Rotor Guards
Remote Control – 8
Functions
Battery Installation
Charging the Battery – 10
Flying – 12
Craft/Remote Link
When You’re Done Flying
Trim Adjustment – 14
Setting Trim & Countering Drift
Gyroscope Recalibration
Remote Trim Reset
Flying Tips & Features – 16
Tips for Safe Operation
Speed Setting
Headless Mode
Flips
Camera & Memory Card – 18
Photos
Video
SD Card Install & Removal
Camera Angle Adjustment
View Photos/Video on a Computer
Parts & Repair – 20
Parts Replacement
Rotor Replacement
Troubleshooting – 21
Customer Support – 22
Contact Information
International Support
Warranty
5
Features
360° flips & tricks
3 speed settings
6-axis gyroscope
.3 MP Camera (photo & video) with SD
card slot
480 x 640 resolution
Control distance: up to 150 feet
Headless Mode
LED navigation lights
Operating time: 6-8 minutes
Charge time: 40-50 minutes
Includes
2.4 GHz remote control: requires 4 AAA
batteries (not included)
Built-in rechargeable lithium polymer
battery
USB cable for battery recharge
4GB SD card
Screwdriver
4 replacement rotors
User’s guide & warranty
Falcon 2 Pro Quadcopter Drone
6
Overview
Craft Layout & Features
Battery Compartment/Camera
Rotors
White rotors indicate
front of craft.
Power Switch
LED Lights
White LEDs
indicate the front
of the craft.
Rotor Guards
Landing Skids
7
Landing Struts
Rotor Guards
Assembly
x4 Standard Screws
Insert pegs into the holes on the
underside of the body as shown.
Insert two wide head screws
per strut and tighten with the
included screwdriver.
Do not over tighten or damage
may occur.
Insert rotor guards into the
holes under the rotors as shown.
Insert one standard screw in
the center position and tighten
with the included screwdriver.
Do not over tighten or damage
may occur.
x4 Wide-head Screws
8
Remote Control
Functions
Headless Mode/
Reset
Press to turn Headless
Mode ON or OFF.
Press to reset trim
settings to default.
Photo/Video
Press to take a
picture.
Press and hold
to take video.
Left Control
Stick/Speed
Increase Throttle:
push forward
Decrease Throttle:
push backward
Yaw/Spin:
push left or right
Change Speed:
push down
Right Control
Stick
Pitch:
push forward/
backward
Roll/Bank:
push left/right
Flip
Press once,
then move Right
Control Stick in
any direction to
perform a flip.
Trim Adjustment
Power Switch
Power Indicator
9
Battery Installation
Insert 4 x AAA Batteries
(not included).
10
Charging the Battery
Before charging, be sure the craft and remote control are powered OFF. Failure to do so may
result in injury.
REMINDER: Do not charge batteries overnight. Do not leave the batteries unattended
while charging.
Step 1
Make sure the craft is powered OFF, then
remove the battery cover.
Step 3
Attach the plug on the battery to the plug on
the charging cable.
Be sure to match the plugs correctly or
damage may occur.
Step 2
Disconnect the power plug connecting the
battery to the craft.
It is strongly recommended to remove the
battery when charging. This will reduce the
chance of damage or injury.
11
Step 5
When charging is complete, reinstall the
battery in its compartment, reconnect the
power plug from the battery to the craft,
and close the battery cover.
Be sure to match the plugs correctly
and securely close the battery cover or
damage may occur.
Step 4
Plug the USB charging cable in to the USB
port of a powered ON computer or USB
power adapter (not included).
While charging, the cable will display a
red light.
When charging is complete, the light will
turn OFF.
12
Flying
Craft/Remote Link
Before flying, the craft and the remote must be linked together and the gyroscopes on the
craft must be allowed to calibrate.
Begin with the battery installed and the craft and remote powered OFF.
Step 2
Power the craft ON. The LED formation
lights will blink in unison as the craft
searches for a signal from the remote.
Step 1
Place the craft on a flat, level surface. This
is necessary for the craft’s gyroscopes to
properly align.
Step 3
Power ON the remote. The light on the
remote will blink as it searches for the
signal from the craft. An audible chime will
sound when the remote and the craft have
linked with each other.
13
Step 4
Push the Left Control Stick (throttle) fully
forward, wait for a chime to sound, then
pull the stick fully rearward, and wait for a
second chime. When this last chime has
sounded the craft is ready to fly.
Step 5
Use the Left Control Stick to take off
and control the throttle and Yaw (spin)
movement of the craft.
Use the Right Control Stick to control the
Pitch (forward/backward) and Roll (left/
right) movement of the craft.
When You’re Done Flying
After landing, pull the Left Control Stick (throttle) fully rearward to power down and wait
for the rotors to stop spinning. Power OFF the remote BEFORE powering OFF the craft.
This will ensure that no signals are accidentally sent by the remote, reducing the chance of
injury. After this is done, it is safe to pick up and power OFF the craft.
14
Trim Adjustment
Setting Trim & Countering Drift
Even after the craft is calibrated, it may show a tendency to drift while airborne. Adjusting
the trim will help counter this effect and allow for better control the craft.
To avoid potential damage, adjust the trim while attempting a stable hover.
Try to avoid making any exaggerated movements with the flight controls.
Adjust one trim setting at a time to avoid confusion.
Remember, the white rotors and LED lights indicate the front of the craft.
Adjusting the trim will help with drift but it will not entirely eliminate it. Turbulence and
other factors may still influence the craft’s flight characteristics.
Craft yaws/spins in place. Adjust Yaw Trim.
Craft banks/rolls left or right. Adjust Roll Trim.
15
Craft pitches/angles
forward or backward.
Adjust Pitch Trim.
Gyroscope Recalibration
If the craft is experiencing difficulty flying or is behaving erratically, it’s gyroscopes may
need to be recalibrated. Do not attempt to do this while flying, safely land the craft first and
place it on a flat surface. The craft and the remote should already be linked together.
Pull down and to the right on both controls sticks for 2-3 seconds. When the LED lights have
stopped blinking and turn solid the recalibration is complete and the craft is ready to fly.
Remote Trim Reset
If you are still having difficulty flying, it may help to reset the trim controls on the remote.
Do not attempt to do this while flying, safely land the craft first.
Press the Reset button on the remote. The remote will chime once to indicate that the trim
has been reset to default.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw GPX DRC377 v1871 Sky Rider Falcon 2 Pro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van GPX DRC377 v1871 Sky Rider Falcon 2 Pro in de taal/talen: Engels als bijlage per email.

De handleiding is 6,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info