39127
70
Verklein
Vergroot
Pagina terug
1/103
Pagina verder
AILE-FLAP (GLID2FLP only): This pre-programmed mix is used to create full span aileron action on a glider with 4
wing servos. This increases the roll rate and decreases induced drag. For normal flying, a value of about 50% is
often used. For slope racing or F3B models in speed runs, you may wish to use a larger value approaching 100%.
Adjustability:
RATE range of -100 to +100. Negative setting would result in opposite aileron action from flaps.
SWITCH A-H fully assignable.
POSITION fully assignable, including NULL (mix always on) and Up&Cntr and Cntr&Dn to activate the mix in 2
separate positions of the same S
WITCH. (This allows easy setup of one SWITCH position which is no FLAP-AILE
or AILE-FLAP mixing, one with both FLAP-AILE and AILE-FLAP mixing, and one with just FLAP-AILE mixing.)
GOAL of EXAMPLE: STEPS: INPUTS:
REAR VIEW OF MODEL WITH LEFT AILERON COMMAND
REAR VIEW OF MODEL WITH LEFT AILERON COMMAND
70
Turn on FLAP-AILE mixing. Set RATE to
48%, which is the portion of the total
aileron travel that matches the maximum
flap travel.
Ex: Set up S
WITCH C as follows:
UP = no full span mixing.
CTR = flap-ail and ail-flap
DWN = flap-ail mixing only.
Assign to S
WITCH C center and down.
Turn on AILE-FLAP mixing. Set rate to
100% for maximum possible flap
travel with ailerons.
Assign to SWITCH C center.
Where next?
Open FLAP-AILE mixing function.
Activate the function.
Set the rate. (Ex: 48%)
Optional: adjust the flap position at
which the flaperons are zeroed.
Assign the S
WITCH
and position.
(Ex: C Cntr&Dn)
Close the function.
Open AILE-FLAP submenu.
Activate the function.
Set the rate. (Ex: 100% each way)
Assign the S
WITCH
and position.
Close.
for 1 second.
(If BASIC menu , again.)
to 2nd page of menu.
to FLAP-AILE.
to ON.
to +48%.
or VR(A) as needed.
for 1 second to set.
to SW. to C.
to Cntr&Dn.
to AILE-FLAP.
to ON.
A
ILERON STICK
. to +100%.
AILERON STICK. to +100%.
to SW. to C.
to CENTER.
ELEV-FLAP mixing. See p. 54.
BUTTERFLY. See p. 55.
Use a mix to OFFSET the flaps a set distance on a specified switch: see p. 59.
View additional model setups on the internet: www.futaba-rc.com\faq\faq-9c.html
70

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futuba 9CHP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futuba 9CHP in de taal/talen: Engels als bijlage per email.

De handleiding is 4,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info