747970
1
Verklein
Vergroot
Pagina terug
1/1
Pagina verder
Link Procedure
Each transmitter has an individually assigned, unique ID code. In order to start
operation, the receiver must be linked with the ID code of the transmitter with
which it is being paired. Once the link is made, the ID code is stored in the
receiver and no further linking is necessary unless the receiver is to be used with
another transmitter.
1
Place the transmitter and the receiver within half a meter of each other.
2
Place the transmitter into the linking mode and turn on the receiver.
3
During countdown, push the receiver tact switch for approximately 2 seconds.
The LED will begin to blink red. After the receiver LED switches from blinking
red to green
green (red) steady light, If the transmitter and receiver are
linked normally, set the power switch to the OFF position and then return it to
the PWR ON position. If the receiver LED lights green, linking was successful.
(T4PLS,T4GRS : set the power switch to the OFF position and then return it to
the PWR ON position.) Actually check servo operation.
* Please refer to the table below for LED status and receiver condition.
* Refer to user manual of the transmitter, to change your transmitter in "Link" mode.
* If there are many T-FHSS systems turned on in close proximity, your receiver might have
difficulty establishing a link to your transmitter. This is a rare occurrence. However, should
another T-FHSS transmitter/receiver be linking at the same time, your receiver could link to the
wrong transmitter. This is very dangerous if you do not notice this situation. In order to avoid
the problem,we strongly recommend you double check whether your receiver is really under
control by your transmitter.
WARNING
After the linking is done, please cycle receiver power and check if the receiver
to be linked is really under the control of the transmitter to be linked.
Do not perform the linking procedure with motor's main wire connected or with
the engine operating as it may result in serious injury.
Note: The R334SBS is compatible with the
T-FHSS SR/T-FHSS system transmitters.
The receiver type setting of the transmitter is
set in T-FHSS SR/T-FHSS.
*Futaba T-FHSS system does not work with current
Futaba S-FHSS/FHSS/FASSTest/FASST/T-FHSS Air
system.
Usage condition on "T-FHSS High Speed mode"
CAUTION
When using the high-speed mode, use a Futaba digital servo (including
brushless servo). Analog servos cannot be used.
• The use of analog servos may cause servo trouble.
Usage condition on "T-FHSS SR mode"
CAUTION
When using the T-FHSS SR mode, use an SR mode servo. Nomal servos
cannot be used.
• The use of nomal servos may cause servo trouble.
1M23N17493
T-FHSS SR/T-FHSS-2.4GHz System
Diversity antenna
S.BUS2, 4-Channel Receiver for Model Car
Thank you for purchasing the
R334SBS
receiver. The
R334SBS
is designed for use
with the Futaba
T-FHSS SR/T-FHSS
system
transmitter. The
R334SBS
receiver has
adopted the newly developed high-speed
response system "
T-FHSS SR
".
• SR servo
The servo corresponding to the SR mode is needed.
The servo type setting of the transmitter is set in SR mode.
• SR mode ON/OFF
ON/OFF of SR mode can be established according to each channel by
a transmitter setting. An OFF channel can use a normal servo/ESC.
Telemetry function
Telemetry function cannot be used for the T-FHSS SR. Do not use the
S.BUS2 port in SR mode.
• Mode Change
To change the system mode, select the system mode (T-FHSS or
7)+6665RIWKHWUDQVPLWWHU¿UVW
Then, making a link between the transmitter and the receiver to build
up the radio linkage.
T-FHSS Re-Link T-FHSS SR
Telemetry system
With the
telemetry system
, the running status can be displayed at the
transmitter. By connecting
S.BUS sensors
that are separately sold into
the
S.BUS2
port of the receiver (R334SBS),
the transmitter will be possible to show the telemetry data on its display.
• Normal mode/High Speed mode
The "Normal mode" accepts any type of servos or the peripheral. The
"High Speed mode" only accepts the digital servos, including BLS
series, and most peripheral equipments such as the brushless ESCs.
Please pay special attention to the information contained within this
manual and transmitter's manual in order to have a pleasant running
experience.
Operating Precautions (T-FHSS):
Once the R334SBS detects the T-FHSS normal mode or T-FHSS high
speed mode, the detected mode is locked as long as the power is ON.
When need to change the mode, please cycle power.
R334SBS
WARNING
NEVER remove the case to avoid the unexpected malfunction. When removing
a case from the double-stick tape, maintain the bottom case.
NEVER use dry batteries for the power supply of the R334SBS as this may
cause difficulties with the receiver's operation.
Wrap the receiver with something soft, such as foam rubber, to avoid vibration.
Do not splash water over the receiver.
Since the receiver generates a certain amount of heat, install in a place with
good ventilation.
Do not put any conductive equipment/sticker on the antenna part. (Receiver
top)
• Otherwise, the operating range may become shorter.
No signal reception LED: Red
Receiving signals LED: Green
Unrecoverable fail-
ure (EEPROM,etc.)
LED: Red and
Green turn on
alternately
R334SBS Specifications:
(
T-FHSS
SR/T-FHSS
system,
S.BUS2
, 4-channel receiver)
Receiving on 2.4GHz band
• System:
T-FHSS SR/T-FHSS
system
Power requirement Operating voltage: 3.7V-7.4V
F/S and Battery F/S function:It is set according to the transmitter used.
Battery F/S voltage: Set it with the transmitter arbitrarily.
Size: 1.33x0.88x0.44” (
33.9x22.3x11.3
mm)
Weight: 0.26oz. (7.5g)
/LQN6ZLWFK岜/('
+8%
%DWWHU\
6WHHULQJVHUYR
7KURWWOHVHUYR
Do not use the S.BUS2 port
in SR mode.
It cannot use the telemetry.
,WFRQQHFWVZLWKSRUWZKLFKLVQRWXVHGك
:KHQDOOWKHSRUWVDUHXVHGFRQQHFW
DEDWWHU\XVLQJ+8%RU<KDUQHVV
%XLOWLQDQWHQQD
5HFHLYHUWRSLVFOHDQ
2XWVLGH$QWHQQD
&+
&+
6%86
&+
7HPSHUDWXUH
VHQVRU
530VHQVRU
9ROWDJHVHQVRU
7HOHPHWU\VHQVRUV
2SWLRQ
'RQWFXWRUEXQGOH
WKHUHFHLYHU
DQWHQQDZLUH
The Example of Connection
LED Indication
Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation, model number R334SBS, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION:
To assure continued FCC compliance:
$Q\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHJUDQWHHRIWKLVGHYLFHFRXOGYRLGWKHXVHUVDXWKRULW\
to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
In case of T-FHSSIn case of T-FHSS SR
FUTABA CORPORATION
Makuhari Techno-Garden Bldg. B-6F, 1-3 Nakase, Mihama-ku, Chiba, 261-8555, Japan
Phone: +81-43-296-8259, Facsimile: +81-43-296-8253
©FUTABA CORPORATION 2017, 6 (1)

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba R334SBS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba R334SBS in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info