29053
6
Verklein
Vergroot
Pagina terug
1/78
Pagina verder
Airplane Section
V-TAIL (VTL)
This
function
automatically
sets
up the PCM
1024Z to
control a V-tail airplane with combined
elevator
and rudder functions. It requires two
servos, one hooked up to receiver output CH2
(elevator 2/rudder) and the second plugged into
CH4 (elevator 2/rudder 1). The elevator and rud-
der deflection can be adjusted independently.
Setting Up V-Tail Mixing
Activation of command
In the Condition Menu, press the
VTL
key to get the
V-TAIL Mixing menu shown below. Use the A key
to activate mode setting, then press the ACT or INH
keys ( F and G) to activate or inhibit V-Tail Mixing.
Mode setting
Elevator 1
deflection angle
Rudder 1
deflection angle
Elevator 2
deflection
angle
Rudder
2
deflection angle
Return to
condition screen
Mode selection
Setting the Elevator Rates - 1 and 2
You now set the rate for Elevator 1. Press the B key
to activate rate setting for Elevator 1 and set the rate with
the numeric keys E to M . The number keys 0 through
100
input the value directly. The + and - keys in-
crease or decrease the value by 1. The +/- key may be
used to reverse the throw direction.
If you are not sure what you are changing, hold the
stick to one side and press different keys if there is no
effect, move the elevator stick to the other side and con-
tinue. Your setting may vary from 100 to +100%, the
initial value is +50%.
Now set the rate for Elevator 2. Press the Q key to
activate Elevator 2 rate setting and set the rate with the
numeric keys as before.
Setting the Rudder Rates - 1 and 2
You now set the rate for Rudder 1. Press the C key to
activate rate setting for Rudder 1 and set the rate with the
numeric keys E to M as before.
If you are not sure what you are changing, hold the
rudder stick to one side and press different keys if there
is no effect, move the rudder stick to the other side and
continue. The initial value is +50%, but your setting may
vary from -100 to +100%.
Now set the rate for Rudder 2. Press the P key to
activate Rudder 2 rate setting and set the rate with the
numeric keys as before.
Checking Your Work
After you have set up the V-Tail rates, be sure that
they move the correct directions. For up elevator com-
mand, both V-tails should move upward. For right rudder
command, the trailing edge of both surfaces should move
to the right. If they do not, use the +/- to reverse the
direction as needed.
Use the
END ( N)
key to leave this menu.
Airplane Section, Page 82
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 9ZHP_part2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 9ZHP_part2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info