29003
16
Verklein
Vergroot
Pagina terug
1/101
Pagina verder
13
While you are installing the battery, receiver, and servos into your
model’s fuselage, please pay attention to the following guidelines:
Use the supplied rubber grommets when
you mount each servo. Be sure not to overtighten
the screws. If any portion of the servo case directly
contacts the fuselage or the servo rails, the rubber
grommets will not attenuate vibration, which can
cause mechanical wear and servo failure.
2.3-2.6mm nut
Flat washer
Rubber grommet
Brass eyelet
Servo mount
2.3-2.6mm screw
Once you have installed the servos, operate each one over its full travel and
check that the pushrod and output arms do not bind or collide with each other,
even at extreme trim settings. Check to see that each control linkage does not
require undue force to move (if you hear a servo buzzing when there is no transmitter
control motion, most likely there is too much friction in the control or pushrod).
Even though the servo will tolerate loads, any unnecessary load applied to the servo
arm will drain the battery pack quickly.
When you are ready to install the switch harness, remove the switch cover and
use it as a template to cut screw holes and a rectangular hole slightly larger than the
full stroke of the switch. Choose a switch location on the opposite side of the
fuselage from the engine exhaust pipe, and pick a location so that it can’t be
inadvertently turned on or off during handling or storage. Install the switch so that it
moves without restriction and “snaps” from ON to OFF and vice versa.
It is normal for the receiver antenna to be longer than the fuselage.
DO NOT cut it or fold it back on itself – cutting or folding changes the
electrical length of the antenna and may reduce range. Secure the antenna to the top
of the vertical fin, and let the excess wire length trail behind. You may run the
antenna inside of a non-metallic housing within the fuselage, but range may suffer if
the antenna is located near metal pushrods or cables. Be sure to perform a range
check before flying.
The receiver contains precision electronic parts. Be sure to avoid vibration,
shock, and temperature extremes.
For protection, wrap the receiver in foam rubber or other vibration-
absorbing materials. It’s also a good idea to waterproof the receiver by placing it
in a plastic bag and securing the open end of the bag with a rubber band before
wrapping it with foam. If you accidentally get moisture inside the receiver, you may
experience intermittent operation or a crash.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 8UHPS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 8UHPS in de taal/talen: Engels als bijlage per email.

De handleiding is 4,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info