29001
84
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
80
The Offset 1, Offset 2,and Offset iv functions are used to offset (change the neutral
position) of the aileron, elevator, and rudder when switch G is used to switch to idle-up 1 (or
2) or switch F is used to switch to inverted flight. This function may be used to automatically
change the trim of a helicopter flying at high speed. A clockwise-rotation rotor helicopter
tends to drift to the right at high speed, so an aileron offset may be applied to offset the
helicopter to the left. You can use the DELAY function to make a smooth transition
between the differing neutral settings.
The necessary elevator offset varies with model geometry, so it must be determined by
noting pitch changes at high speed. The rudder offset is affected by both revolution mixing
(page 72), and trim (overall level movement) with the offset function. When the offset
function is ON, also the electronic trim levers will operate, so the trim amount in these flight
modes is automatically input to each offset amount.
The activating switches are initially set so that offset 1 and offset 2 are on at the same
time as the idle-up 1 and idle-up 2 functions, switched by Switch G. If desired, the offset
function ON/OFF operation can be changed to switch C. This may only be done in the
OFST-1 menu, and not in the OFST-2 menu.
Setting up Offsets 1, 2, & iv
To DELAY
or OFST-2
function
To OFST-1
or TH-HLD
function
Offset amount
Range: -120 to
+120%
(Initial value: 0%)
Data input keys
These keys are used to move
through the five submenus in
the OFST1 & OFST2
functions.
2. Aileron offset
Input the desired Aileron offset with
the (+)/(-) keys.
3. Elevator offset
Input the desired Elevator offset
with the (+)/(-) keys.
4. Rudder offset*
Input the desired Rudder offset with
the (+)/(-) keys.
• If you're unhappy with what you've
set, you may reset to zero by
pressing the (+) and (-) keys
simultaneously.
5. Switch direction selection
Select the desired switch and direction for the switch to turn the
function on and off with the (+)/(-) keys.
SW-E: Turns OFST1 & 2 on/off at the same time as idle-ups 1 & 2
SW-C modA: Switch C center position turns on OFST-1 and lower
position turns on OFST-2
SW-C modB: Switch C center position turns on OFST-1 and upper
position turns on OFST-2
1. Turn the OFST1, OFST2, or OFSTiv function ON or OFF by
pressing the (+) key ("ON" or "OFF" displayed depending
on switch G's or F’s position). Turn off (INH) the function with
the (-) key.
Switch direction display (SW-E,
SW-C modA, SW-C modB)
(Initial value: SW-E)
Channel display
AIL = Aileron
ELE = Elevator
RUD = Rudder
The screen below only appears in the
OFST-1 menu for switch setting.
The Delay function provides a smooth transition between the trim positions whenever
offset, revolution mixing, or throttle hold functions are turned on and off. You may set
different delay times for aileron, elevator, and rudder. With a 50% delay setting, the servo
takes about a half-second to move to its new position, quite a long time. Normally a 10-15%
delay is used.
84

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 8UAPS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 8UAPS in de taal/talen: Engels als bijlage per email.

De handleiding is 4,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info