28993
59
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
2. Now press the
CURSOR
key twice, this
will cause the plus or minus sign in front
of the large number to flash on and off.
You can set the direction of revolution
mixing on each side of the half-throttle
position by changing this flashing sign
with the (+) or (–)
DATA INPUT
keys.
Therefore, you’ll either set plus or minus
for both sides of the throttle stick’s motion
(indicated by the
R/U
or
L/D
indicator in
the window).
Use the (+) or (–) key to match the mixing
direction to the rotor rotation: (–) gives
right rudder, (+) gives left rudder. Verify
that you get the proper motion of the
rudder channel when you move the
throttle. You’ll set the amount of travel in
the next step.
3. Again press the
CURSOR
key; this will
cause the small percent sign in front of the
large number to flash on and off. At this
point you choose the percentage of revo
mixing for both sides of half throttle. You
may set a value of 0% to 100% for each
side by moving the throttle stick in both
directions, one at a time, and changing the
percentage number to suit. Now verify
that the rudder responds both the correct
direction and amount for travel on both
sides with the master control. If you wish
to return the mixing percentage to the
default 50% value, press both the (+) and
(–) keys simultaneously.
R-OF — Rudder Offset
The rudder offset function is used to change the neutral position (offset) of the rudder
when switch E is used to switch to idle-up. This function may be used to automatically change
the trim of a helicopter flying at high speed. A clockwise-rotation rotor helicopter tends to drift
to the right at high speed, so a rudder offset may be applied to yaw the helicopter to the left.
The necessary offset varies with model geometry, so it must be determined by noting
changes at high speed. The rudder offset is affected by both revolution mixing and trim.
Rudder offset is turned on at the same time as idle-up, switched by switch D.
Setting up Rudder Offset
1. Press one of the
MODE SELECT
buttons
until the
R-OF
window appears. The
default is for the function to be inhibited.
To activate, press the
CURSOR
key, then
press the (+)
DATA INPUT
key. This will
cause the flashing
INH
display to change to
a flashing
ON
or
OFF
display, depending
on the idle-up switch’s position.
2. Press the
CURSOR
key once. The percent
indicator should begin flashing.
3. Now you can adjust the rudder offset
position with the (+) or (–)
DATA INPUT
keys, anywhere between -100 and +100%
– 54 –
59

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 6XH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 6XH in de taal/talen: Engels als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Futaba 6XH

Futaba 6XH Gebruiksaanwijzing - Espanôl - 55 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info