28993
54
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
9. Revolution Mix Setting
Revolution mixing (
REVO
) uses the tail
rotor to suppress the torque reaction of the
main rotor due to changes in collective pitch.
It is disabled whenever Idle-Up or Throttle
Hold are activated.
REVO
may be set on either side of the stick
(note the letters
R/U
and
L/D
displayed).
Adjust
REVO
mixing for both travel directions
as described in the trimming instructions
following.
Idle-Up & Throttle Hold
Your system is already programmed to
provide Idle-up [
IDLE
] and Throttle Hold
[
HOLD
]. Idle-up is typically used for 540°
stall turns, looping, and rolling stall turns;
throttle hold is used to disengage the throttle
during autorotations. After activation, these
functions are switched on as follows:
• Idle-up [
IDLE
] –
ON
at Switch E’s forward
position. Idle-up also turns on Rudder offset
function
• Throttle Hold [
HOLD
] –
ON
at Switch D
forward position.
When these two switches are OFF, the
radio is set up for regular hovering and flight.
As these functions are switched on or off,
HOLD
has highest priority, followed by
IDLE
.
Regular settings are when both are off.
10. Rudder Offset Setting
The Rudder Offset menu [
R-OF
] is only
turned on when Idle-up has been activated.
Rudder trim may be offset to different
positions so that the model flies straight ahead
during normal flight. Recommended settings
are small, from 6% to 10% or as needed.
11. Throttle Hold Setting
Throttle hold (
HOLD
) commands the
throttle to a preset position near idle and
disconnects it from pitch when activated.
Move to the
HOLD
menu and activate by
pressing the (+) key, then move switch D to
the forward position. Set the hold position to
maintain engine speed near idle without
engaging the main rotor clutch.
12. Dual Rate Settings
If you find that your aileron and elevator
controls are too sensitive, you may set dual
rates to reduce them. Use the dual rate (
D/R
)
window to adjust them to the desired amount
of response when the switch is flipped.
If you want both dual rate circuits to be
controlled by a single switch, use mode 2 in
the
DRSW
menu. Otherwise, leave it at mode
1.
12. Trim Memory
Once your chopper is flying the way you
like, memorize the trim positions with the
TMEM
window.
This concludes the example setup
procedure for helicopters. Be sure to browse
through the pages following this example to
see the details about the menus for helicopters.
– 49 –
54

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 6XH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 6XH in de taal/talen: Engels als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Futaba 6XH

Futaba 6XH Gebruiksaanwijzing - Espanôl - 55 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info