28989
39
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
ELVN — Elevon Mixing
The Elevon function should be used with delta wings, flying wings,
and other tailless aircraft whose layouts combine the aileron and elevator
functions, and requires one servo for each elevon. Connect the right
aileron to receiver CH1/AIL and the left aileron to CH2/ELE.
1CH
Aileron operation
Elevator operation
2CH
The amount of aileron and elevator response can be adjusted
independently. However, if you program in too much elevator or rudder
travel, the servos may reach their travel limits before full stick motion has
occurred. Therefore, you should keep the travel settings at 50% or below
and adjust the control linkages to get the travel you desire.
NOTE: The elevon, V-tail, and flaperon functions cannot be activated simultaneously.
The function activated last has priority.
Setting up elevon mixing
1. Use the up or down arrow keys to select the
ELVN
window.
2. Press the
CURSOR key three times to get to the activation setting. The INH
indicator will flash on and off.
3. Now press the (+) key to enable the elevon function. The display will
show a flashing ON.
4. Press the
CURSOR key once, to get to the aileron setting menu. A small
arrow is displayed over the numeral 1 (representing aileron master
channel), and the plus or minus sign above the large setting number will
blink on and off.
Move the aileron stick all the way to the right: the right elevon should move upwards, and
the left elevon should move downwards. If they move opposite to this, change the aileron
travel direction with the (+) and (–) keys. Note that this reverses the response at both elevon
servos (not just one as in the REV menu). If both servos move the same direction, reverse
the one that moves improperly in the REV menu.
5. Now you’ll input the amount of aileron travel by pressing the
CURSOR key once. Now the
percent sign will blink on and off, and you may adjust the amount of aileron travel with the
(+) and (–) keys. You may change the initial 50% setting to be anywhere between 0% and
100% (press the plus and minus keys together if you wish to reset to 50%).
6. Next: the elevator inputs. Press the
CURSOR key once. A small arrow
should appear over the numeral 2 in the screen (indicating elevator is the
master channel), and the sign in front of the large setting number will flash
on and off. Verify that when you pull back on the elevator stick, both the elevon servos
move upwards. If they move the incorrect direction, change the direction by pressing the (+)
or (–) key which changes the flashing sign displayed.
7. Now you’ll input the amount of elevator travel by pressing the
CURSOR key once. Now the
percent sign will blink on and off, and you may adjust the amount of elevator travel with the
(+) and (–) keys. You may change the initial 50% setting to be anywhere between 0% and
100% (press the plus and minus keys together if you wish to reset to 50%). Remember to be
sure not to have so much travel as to cause binding when both elevator and aileron are
commanded simultaneously.
– 34 –
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 6XA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 6XA in de taal/talen: Engels als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Futaba 6XA

Futaba 6XA Gebruiksaanwijzing - Espanôl - 55 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info