29031
41
Verklein
Vergroot
Pagina terug
1/127
Pagina verder
1. Model addition and call
Default setting assigns 1 model to the T14MZ. To
add new models or to call a model already set, use the
Model Select function of the Linkage Menu.
This is convenient when calling a model after
registering the model names in advance. (The data of
up to 30 models can be saved at the transmitter. Data
can also be saved to the accessory Data-Pack.)
The currently called model is displayed at the top
of the screen. Before ying and before changing any
settings, always con rm the model name.
Please be aware that the transmitter will stop
transmitting when you change the model.
When a new model is added, the Model Type Select
screen and Frequency/Modulation mode/Receiver ID
setup screen automatically appear. Change, or check
that they match the type, frequency, and receiver type
of the model used.
2. Model type and swash type selection
When a separate model type is already selected,
select helicopter with the Model Type function of the
Linkage Menu, and then select the swash type matched
to the fuselage.
Helicopter basic setting procedure
3. Flight condition addition
The transmitter can install up to eight flight
conditions per model. You can assign all switches
including sticks, switches, trim levers and trim switches
as flight-condition selection switches. You can also
add delayed mixing to these functions in order to
avoid sudden changes. Moreover, you can set priority
order for ight conditions when you set more than one
condition. In addition, you can copy conditions and/or
change names of conditions. This command may also
be used to define what switches and/or controls are
used to activate each ight condition.
The Condition Select function automatically allocates
the Condition 0 for each model type. Condition 0 is
the default condition, also referred to as Normal, and is
the only one active when a new model type is de ned.
This condition is always on, and remains on until other
conditions are activated by switches.
The Condition Delay can be programmed for each
channel. The Condition Delay is used to change the
servo throw smoothly when switching conditions.
(General ight condition setting example)
Normal: (Use initial setting conditions/operate
when switch OFF)
Use from engine starting to hovering.
Idle up 1: (Switch setting example: Operate
at SW-E center)
Use in 540o stall turn, loop, rolling stall turn, and
other maneuvers.
Idle up 2: (Switch setting example: Operate
at SW-E forward side)
Use in rolls.
Throttle hold: (Switch setting example:
Operate at SW-G forward side)
Use in auto rotation.
The priority is throttle hold/idle up 2/idle up 1/
normal. Throttle hold has the highest priority.
Add other conditions, as required.
41
<Model Basic Setting Procedure>
41

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Futaba-14MZ

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 14MZ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 14MZ in de taal/talen: Engels als bijlage per email.

De handleiding is 21,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info