691367
6
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
2
Adjust the brightness level.
Enabling Standby Mode
You can set the stereo to enter a low-power standby mode when
you turn off the ignition or hold . When you turn on the ignition
or press again, it takes less than the typical 30 seconds to
turn on.
NOTE: When the stereo is in low-power standby mode, it
continues to draw current from the battery. The maximum
current draw in standby mode is 50 mA.
Select > SETTINGS > POWER OPTIONS > STANDBY
MODE.
The stereo now enters standby mode when you hold .
Audio Control
Adjusting the Volume
1
Turn the dial to adjust the volume.
2
If necessary, press the dial to switch between zones.
TIP: To control all zones at the same time, press the dial
repeatedly to select GLOBAL.
Muting all Connected Stereos
You can quickly mute the audio from this stereo or from all
stereos connected to the network (FUSION PartyBus
Networking, page 8).
1
From any source, select .
The mute symbol appears and audio from this stereo is
silenced.
2
Press and hold the dial to select MUTE SYSTEM.
Audio from all connected stereos is silenced.
3
Press the dial to select UNMUTE SYSTEM.
Audio is restored to all connected stereos.
Adjusting the Tones
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select TONE.
4
Select an option:
Use the slider bar to adjust the level of each tone.
Press the dial to select a tone, and turn the dial to adjust
the level for the tone.
Disabling the Loud Setting for a Zone
The LOUD setting maintains frequency response at low volumes
and increases perceived loudness at high volumes. This setting
is enabled by default in all zones.
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select LOUD to clear the check box.
Adjusting the Gain for an Auxiliary Device
You can adjust the gain for a connected auxiliary device to
achieve a volume level similar to that of other media sources.
You can adjust the gain in 1 dB increments. You can also adjust
the gain for digital sources using an optical audio connection.
1
Select an auxiliary source.
2
Select an option:
To increase the gain, select .
To decrease the gain, select .
NOTE: To achieve the best audio quality when using a
portable media player with headphone output, it may be
necessary to adjust the volume control on the media player,
instead of adjusting the gain.
Synchronizing the Source and Zone Volume
Levels
You can synchronize the volume levels on one or all zones with
some source devices, such as a Bluetooth source.
1
Select > SETTINGS > ZONE > PHONE VOLUME ZONE
SYNC.
2
Select a zone or GLOBAL.
When you adjust the volume on the source device, the volume
on the selected zone is also adjusted.
Speaker Zones
You can group speakers in one area into a speaker zone. This
enables you to control the audio level of the zones individually.
For example, you could make the audio quieter in the cabin and
louder on deck.
You can set the balance, volume limit, tone, subwoofer level,
subwoofer frequency, and name for each zone, and configure
other zone-specific settings (Speaker Zone Settings, page 9).
Adjusting Additional Audio Settings for a Zone
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select MORE.
4
Select one or more options:
NOTE: Not all options are available for all zones.
To limit the maximum volume output of this zone, select
VOLUME LIMIT, and adjust the level.
To set the subwoofer level for this zone, select SUB
LEVEL, and adjust the level.
To adjust the right and left speaker balance of this zone,
select BALANCE, and adjust the balance.
Adjusting the Subwoofer Filter
You can use the subwoofer filter setting to control the subwoofer
cutoff frequency for each zone, which can enhance the blend of
the sound produced by the speakers and the subwoofer. Audio
signals above the selected frequency are not passed to the
subwoofer.
NOTE: If a DSP setting has been applied to zone, this setting
cannot be changed on the stereo. You can view the DSP setting
for the optimal cutoff frequency as calculated by the DSP
controller, but cannot adjust it.
1
Select > SETTINGS > ZONE.
2
Select a zone.
3
Select SUB FREQ.
4
Select a frequency.
DSP Settings
This stereo features digital signal processing (DSP). You can
select pre-configured DSP settings for FUSION
®
speakers and
amplifiers to optimize audio reproduction in their installed
locations.
All DSP settings are configured using the FUSION-Link
remote
control app (FUSION-Link Wireless Remote Control App,
page 10).
Configuring the DSP Settings
You must download and install the FUSION-Link remote control
app on your compatible Apple
®
or Android
device before you
can configure the DSP settings (FUSION-Link Wireless Remote
Control App, page 10).
2 Audio Control
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fusion Apollo MS-RA670 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fusion Apollo MS-RA670 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Fusion Apollo MS-RA670

Fusion Apollo MS-RA670 Gebruiksaanwijzing - Nederlands - 20 pagina's

Fusion Apollo MS-RA670 Gebruiksaanwijzing - Deutsch - 20 pagina's

Fusion Apollo MS-RA670 Gebruiksaanwijzing - Français - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info