522155
123
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
COLOR GPS/PLOTTER/SOUNDER
GP-7000F
Your Local Agent/DealerYour Local Agent/Dealer
9-52 Ashihara-cho,9-52 Ashihara-cho,
Nishinomi
y
a 662-8580, JAPANNishinomi
y
a 662-8580, JAPAN
Tele
p
hone :Tele
p
hone : 0798-65-21110798-65-2111
FaxFax 0798-65-42000798-65-4200
::
F
IRST EDITION :
F
IRST EDITION :AUGAUG.. 20042004
Printed in JapanPrinted in Japan
A
ll ri
g
hts reserved.
A
ll ri
g
hts reserved.
Pub. No.Pub. No. OME-44291OME-44291
*
00014913700
*
*
00014913700
*
*
00014913700
*
*
00014913700
*
(( HIMAHIMA ))
GP-7000FGP-7000F
* 0 0 0 1 4 9 1 3 7 0 0 ** 0 0 0 1 4 9 1 3 7 0 0 *
*
OME
A
00
*
*
OME
A
00
*
*
OME
A
00
*
*
OME
A
00
*
* O M E 4 4 2 9 1 A 0 0 ** O M E 4 4 2 9 1 A 0 0 *
IMPORTANT NOTICE
No part of this manual may be copied or reproduced without written permission.
If this manual is lost or worn, contact your dealer.
The contents of this manual and equipment specifications are subject to change without
notice.
The example screens (or illustrations) shown in this manual may not match the screens
you see on your display. The screen you see depends on your system configuration and
equipment settings.
This manual is intended for use by native speakers of English.
FURUNO will assume no responsiblity for the damage caused by improper use or
modification of the equipment or claims of loss of profit by a third party.
i
SAFETY INSTRUCTIONS
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury
can result.
Do not open the equipment.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can
cause electrical shock.
Do not operate the equipment with wet
hands.
Electrical shock can result.
Use the proper fuse.
Fuse rating is shown on the power cable.
Use of a wrong fuse can result in damage
to the equipment.
Hazardous voltage which can cause
electrical shock, burn or serious injury
exists inside the equipment. Only qualified
personnel should work inside the equipment.
WARNINGWARNING
CAUTION
Do not use the equipment for other than
its intended purpose.
No one navigation device should ever be
solely replied upon for the navigation of
a vessel.
Always confirm position against all available
aids to navigation, for safety of vessel and
crew.
Do not turn on the equipment with the
transducer out of water.
The transducer may be damaged.
Use the proper gain setting.
Incorrect gain may produce wrong depth
indication, possibly result ing in a
dangerous situation. See "Adjusting the
gain" on page 10-11.
The picture is not refreshed when
picture advancement is stopped.
Maneuvering the vessel in this condition
may result in a dangerous situation.
A warning label is attached to the equip-
ment. Do not remove the label. If the
label is missing or illegible, contact
a FURUNO agent or dealer.
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Name: Warning Label (1)
Type: 86-003-1011-1
Code No.: 100-236-231
The TFT LCD is constructed using the
latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01%
of the pixels may drop out or blink, how-
ever this is not an indication of malfunc-
tion.
About the TFT LCD
Do not maneuver the vessel based
on the depth indication alone.
Grounding may result.
ii
FOREWORD
Congratulations on your choice of the FURUNO GP-7000F COLOR
GPS/PLOTTER/SOUNDER. We are confident you will see why the FURUNO
name has become synonymous with quality and reliability.
For over 50 years FURUNO Electric Company has enjoyed an enviable
reputation for innovative and dependable marine electronics equipment. This
dedication to excellence is furthered by our extensive global network of agents
and dealers.
This equipment is designed and constructed to meet the rigorous demands of
the marine environment. However, no machine can perform its intended function
unless installed, operated and maintained properly. Please carefully read and
follow the recommended procedures for operation and maintenance.
Features
The GP-7000F provides a totally integrated GPS receiver, color video plotter and
color video sounder.
The GPS receiver tracks up to 13 satellites (GPS: 12, WAAS: 1) simultaneously,
and an 8-state Kalman filter ensures optimum accuracy in determination of
vessel position, course and speed.
C-MAP NT chart card (SD) is available.
Comprehensive navigation data displays.
Bright 7-inch color TFT LCD with brilliance control.
Automatic coastline chart loading.
Position display in latitude and longitude, Loran C TD.
Alarms: Arrival, Anchor Watch, Cross-track Error, Speed, Grounding, Fish,
Depth, Temperature.
Man overboard feature records latitude and longitude coordinates at the time
of man overboard.
“Highway” display provides graphic presentation of ship’s track and is useful
for monitoring cross track error.
Automatic or manual video sounder operation.
iii
TABLE OF CONTENTS
SYSTEM CONFIGURATION............................................................................... vii
1. OPERATIONAL OVERVIEW .........................................................................1-1
1.1 Display Unit Controls....................................................................................................1-1
1.2 Loading an SD
TM
Chart Card........................................................................................ 1-2
1.3 Turning the Power On/Off.............................................................................................1-3
1.4 Adjusting Brilliance and Contrast..................................................................................1-4
1.5 Selecting a Display ......................................................................................................1-5
1.6 Soft Keys .....................................................................................................................1-5
1.7 MOB Mark....................................................................................................................1-6
1.7.1 Entering MOB mark, setting MOB as destination.............................................1-6
1.7.2 Deleting the MOB mark...................................................................................1-7
1.8 Menu Operation...........................................................................................................1-7
1.9 Simulation Mode ..........................................................................................................1-9
2. PLOTTER DISPLAYS ....................................................................................2-1
2.1 Presentation Modes .....................................................................................................2-1
2.1.1 North-up..........................................................................................................2-1
2.1.2 Course-up .......................................................................................................2-2
2.1.3 Auto course-up................................................................................................2-2
2.2 Cursor..........................................................................................................................2-3
2.2.1 Turning on the cursor, shifting the cursor.........................................................2-3
2.2.2 Moving the cursor to the center of the screen..................................................2-3
2.2.3 Displaying data................................................................................................2-4
2.3 Selecting Chart Scale/Range .......................................................................................2-4
2.4 Navigation Data Display...............................................................................................2-5
2.5 Compass Display.........................................................................................................2-6
2.6 Highway Display ..........................................................................................................2-7
2.7 GPS Status Display......................................................................................................2-8
2.8 Tide, Celestial Display ..................................................................................................2-9
2.9 Graph Display ............................................................................................................2-10
2.10 Wind Display............................................................................................................ 2-11
3. TRACK ...........................................................................................................3-1
3.1 Selecting Active Track..................................................................................................3-1
3.2 Displaying Track........................................................................................................... 3-2
3.3 Changing Track Color ..................................................................................................3-2
3.4 Stopping, Restarting Plotting........................................................................................3-2
3.5 Hiding the Track...........................................................................................................3-3
3.6 Track Plotting Method and Interval...............................................................................3-3
3.6.1 Track plotting method...................................................................................... 3-3
3.6.2 Track plotting interval ......................................................................................3-4
3.7 Erasing Track...............................................................................................................3-4
iv
4. WAYPOINT.....................................................................................................4-1
4.1 Entering Waypoints...................................................................................................... 4-1
4.1.1 Entering a waypoint at own ship position or cursor position ............................ 4-1
4.1.2 Entering a waypoint from the waypoint list ...................................................... 4-3
4.2 Editing Waypoint Data ................................................................................................. 4-4
4.2.1 Editing waypoint data from the waypoint list................................................... 4-4
4.2.2 Editing a waypoint from the plotter display...................................................... 4-4
4.3 Erasing Waypoints....................................................................................................... 4-5
4.3.1 Erasing a waypoint directly from the plotter display......................................... 4-5
4.3.2 Erasing a waypoint from the waypoint list ....................................................... 4-5
4.4 Searching, Sorting Waypoints...................................................................................... 4-6
4.5 Other Waypoint List Functions..................................................................................... 4-7
4.5.1 Filtering waypoints by mark shape.................................................................. 4-7
4.5.2 Hiding or showing waypoints........................................................................... 4-8
4.5.3 Searching waypoints....................................................................................... 4-8
5. ROUTE ...........................................................................................................5-1
5.1 Entering Routes........................................................................................................... 5-1
5.2 Changing the Route Name/Comment ......................................................................... 5-2
5.3 Connecting Routes...................................................................................................... 5-3
5.4 Inserting Waypoints ..................................................................................................... 5-4
5.5 Removing Waypoints from a Route.............................................................................. 5-5
5.6 Information on Route Report ...................................................................................... 5-6
5.7 Changing the Color of Route Line .............................................................................. 5-7
5.8 Searching Routes........................................................................................................ 5-8
5.9 Reversing the Waypoints Order in a Route.................................................................. 5-8
5.10 Erasing Routes.......................................................................................................... 5-8
6. NAVIGATION..................................................................................................6-1
6.1 Navigating to Quick Points........................................................................................... 6-1
6.2 Navigating to Waypoints .............................................................................................. 6-4
6.3 Following a Route........................................................................................................ 6-5
6.4 Cancelling Navigation.................................................................................................. 6-6
7. ALARMS ........................................................................................................7-1
7.1 Audio Alarm On/Off...................................................................................................... 7-2
7.2 Arrival Alarm ................................................................................................................ 7-2
7.3 XTE (Cross-Track Error) Alarm.................................................................................... 7-3
7.4 Temperature Alarm ...................................................................................................... 7-4
7.5 Anchor Alarm............................................................................................................... 7-5
7.6 STW Alarm .................................................................................................................. 7-5
7.7 Depth Alarm.................................................................................................................7-6
7.8 Grounding Alarm...........................................................................................................7-7
8. CUSTOMIZING YOUR UNIT..........................................................................8-1
8.1 GENERAL Menu.......................................................................................................... 8-1
8.2 MAP Menu................................................................................................................... 8-2
8.3 ADVANCED Menu....................................................................................................... 8-4
8.4 INFO Menu.................................................................................................................. 8-6
v
8.5 FIND Menu ..................................................................................................................8-6
9. DATA TRANSFER..........................................................................................9-1
9.1 Memory Card Operations.............................................................................................9-1
9.1.1 Selecting the card slot to use ..........................................................................9-1
9.1.2 Formatting memory cards................................................................................9-2
9.1.3 Saving data to a memory card.........................................................................9-2
9.1.4 Playing back data from a memory card ...........................................................9-3
9.2 Uploading/Downloading Data....................................................................................... 9-3
9.2.1 Uploading/downloading waypoints data...........................................................9-3
9.2.2 Uploading/downloading routes data ................................................................9-5
10. VIDEO SOUNDER OPERATION ...............................................................10-1
10.1 Sounder Display....................................................................................................... 10-2
10.1.1 Description of sounder display ......................................................................10-2
10.1.2 Selecting a sounder display........................................................................... 10-4
10.2 Automatic Sounder Operation .................................................................................. 10-8
10.2.1 How the automatic sounder works.................................................................10-8
10.2.2 Types of automatic sounder mode................................................................. 10-9
10.2.3 How to enable automatic sounder operation.................................................. 10-9
10.3 Manual Sounder Operation .................................................................................... 10-10
10.3.1 Selecting the manual mode......................................................................... 10-10
10.3.2 Selecting display range ............................................................................... 10-10
10.3.3 Adjusting the gain........................................................................................ 10-11
10.4 Measuring Depth, Time.......................................................................................... 10-12
10.5 Reducing Interference............................................................................................ 10-13
10.6 Reducing Low Level Noise..................................................................................... 10-14
10.7 Erasing Weak Echoes............................................................................................10-15
10.8 White Marker.......................................................................................................... 10-16
10.9 Picture Advance Speed..........................................................................................10-17
10.10 Alarms..................................................................................................................10-18
10.10.1 Audio alarm On/Off ................................................................................... 10-18
10.10.2 Fish alarm.................................................................................................10-19
10.10.3 Fish alarm (B/L) ........................................................................................ 10-19
10.11 Water Temperature Graph....................................................................................10-20
10.12 Reviewing Past Picture ........................................................................................ 10-20
10.13 Displaying Nav Data............................................................................................. 10-21
10.14 SOUNDER SETUP Menu .................................................................................... 10-22
10.15 Interpreting the Sounder Display.......................................................................... 10-24
11. MAINTENANCE & TROUBLESHOOTING................................................11-1
11.1 Maintenance............................................................................................................. 11-1
11.2 Replacement of Fuse ............................................................................................... 11-2
11.3 Replacing of Battery................................................................................................. 11-2
11.4 Simple Troubleshooting............................................................................................ 11-3
11.5 Diagnostics............................................................................................................... 11-5
11.5.1 RAM menu.................................................................................................... 11-5
11.5.2 Dim menu...................................................................................................... 11-6
11.5.3 Cartridge....................................................................................................... 11-6
vi
11.5.4 Serial ports ....................................................................................................11-7
11.6 Clearing the Memory.................................................................................................11-8
11.7 GPS Cold Start .........................................................................................................11-8
APPENDIX ......................................................................................................AP-1
Menu Tree.......................................................................................................................AP-1
What is WAAS?...............................................................................................................AP-5
World Time Chart.............................................................................................................AP-6
SPECIFICATIONS........................................................................................... SP-1
INDEX............................................................................................................... IN-1
vii
SYSTEM CONFIGURATION
TRANSDUCER
Speed/Water
Temp Sensor
(option)
Distributor
MB-1000*
* Required when using
1 kW transducer.
Power Source
12-24 VDC
: Option
: Standard
: User Supply
NMEA1 and NMEA2 ports:
Radar, autopilot, video sounder,
temperature indicator, etc.
PC/NMEA IN port:
PC, NMEA device, buzzer
ANTENNA UNIT GPA-017
DISPLAY UNIT
GP-7000F
How to remove the hard cover
Place your thumbs at the center
of the cover, and then lift the cover
while pressing it with your thumbs.
viii
1-1
1. OPERATIONAL OVERVIEW
This chapter acquaints you with the basics of your unit–from turning on the
power to the soft key menu operation.
1.1 Display Unit Controls
CLEAR
BRILL
POWER
GOTO
WPT
SAVE
MOB
DISP
TO ENTER
PUSH
MENU
RANGE
Soft keys
Card slot
Cursor pad
RANGE key
ENTER knob
See below.
MENU
DISP
MOB
WPT
TLL
GOTO
ROUTE
CLEAR
POWER
BRILL
Opens the menu.
Opens the DISPLAY MODE menu.
Enters waypoint or MOB mark.
Brief press:
Sets/releases the the destination.
Long press: Outputs the TLL data.
Closes the menu and window.
Brief press: Turns power on./Shows the brilliance setting window.
Long press: Turns power off.
Shows the route list.
Display unit, front view
1. OPERATIONAL OVERVIEW
1-2
1.2 Loading an SD
TM
Chart Card
Your unit reads C-MAP NT
+ TM
charts, stored on SD
TM
cards. Insert the
appropriate chart card for your area before turning the power on to show chart
data automatically.
Note 1: Static electricity can be passed through your fingers to a card and
destroy the contents of the card. To prevent this, always touch a metallic
object, such as a steel desk, before handling an SD
TM
card.
Note 2: Do not insert or remove a card while the power is on. This may cause
the equipment to freeze.
1. Push down the lid catch to open the card slot cover.
CLEAR
BRILL
POWER
GOTO
WPT
SAVE
MOB
DISP
TO ENTER
PUSH
MENU
RANGE
Card slot cover
Lid catch
Card slot cover
2. Insert appropriate SD
TM
chart card label side up to any slot.
Inside SD chart card
label side up.
Insert
direction
SD
TM
chart card
3. Press the center of the lid catch to close the card slot cover, to protect the
chart drive. (Keep the slot cover closed at all times.)
1. OPERATIONAL OVERVIEW
1-3
1.3 Turning the Power On/Off
Turning the power on
Press the [POWER/BRILL] key until you hear a click and a beep. When the unit
is turned on, it proceeds in the sequence shown in the figure below.
In about 30 seconds the
last-used display appears.
You can go to the last-used
display faster by pressing any
key when this screen appears.
GP-7000F
GPS PLOTTER SOUNDER
FURUNO ELECTRIC CO., LTD.
STARTUP TEST
PLOTTER
ROM : OK
RAM : OK
BACKUP DATA : OK
INTERNAL BATTERY : OK
INTERNAL GPS : OK
ECHO SOUNDER
ROM : OK
RAM : OK
POWER SETTING : 600 W (or 1 KW)
C-MAP electronic charts (ECs) are derived from
geographical data -including official government
charts - which we believe to be accurate.They are
neither verified nor approved by Hydrographic
Authorities. C-MAP ECs are designed only to ease
and speed navigation calculations and so must not
be relied upon as aprimary source of navigation
information, but rather a backup to the use of
official government charts and prudent navigation
habits.
There is no direct relationship between the color
of water areas and their depth. The navigator shall
always query the area for depth information and use
the official paper charts.
WARNING
Start-up sequence
Note 1: The example screens shown in this manual may not match the screens
you see on your display. The screen you see depends on your system
configuration and equipment settings.
Note 2: If the message “SYSTEM HAS FAILED START UP TEST. PLEASE
CONTACT A LOCAL FURUNO REPRESENTATIVE FOR REPAIR.
PRESS ANY KEY TO CONTINUE.” appears, contact your dealer for
advice.
Note 3: At the very first time you turn on your unit, the simulation mode window
appears. Choose YES or NO as appropriate and push the [ENTER]
knob.
The equipment takes 90 seconds to find its position when turned on for the very
first time. Thereafter it takes about 12 seconds to find position each time the
power is turned on. The message “NO FIX”, which means the equipment is now
finding its position, appears at the bottom of the plotter display immediately after
turning the power on. When the GPS receiver finds its position, “NO FIX”
changes to “2D” or “3D” to show that position data is now accurate.
Turning the power off
Press and hold the [POWER/BRILL] key until the screen goes blank (about four
seconds).
1. OPERATIONAL OVERVIEW
1-4
1.4 Adjusting Brilliance and Contrast
You can adjust display brilliance and contrast as shown below.
1. Press the [POWER/BRILL] key momentarily.
The BACKLIGHT window appears.
BACKLIGHT
ENTER TO SET
Backlight window
2. Rotate the [ENTER] knob to adjust.
Rotate clockwise to raise the setting or counterclockwise to decrease it.
To escape from this window without adjusting, press the [CLEAR] or
[POWER/BRILL] key, or wait three seconds to let the equipment close it
automatically.
3. Press the [ENTER] key to close the window.
1. OPERATIONAL OVERVIEW
1-5
1.5 Selecting a Display
Ten screen displays are available: Plotter, Plotter/Data, Plotter/Compass,
Plotter/Highway, Data/Compass, Satellite status, Celestial, Graph, Wind graph
and Sounders.
1. Press the [DISP] key to show the DISPLAY MODE screen.
DISPLAY MODE
TURN KNOB TO SELECT DISPLAY MODE AND PRESS KNOB TO ENTER.
Display mode screen
2. Use the cursor pad or [ENTER] knob to select a mode.
To escape from the display mode screen without changing the display mode,
press the [DISP] key.
3. Press the [ENTER] knob to set the new display mode.
1.6 Soft Keys
The soft keys, their labels displayed at the bottom of the screen, provide for easy
execution of a desired function, and their label and function change according to
the display in use. When you turn on the power, the soft keys do not appear. To
show the soft keys, press any soft key. To access a soft key function, press the
appropriate soft key within five seconds after accessing them.
Soft keys
The soft keys disappear after five seconds. If you want to erase them earlier,
press the [CLEAR] key.
1. OPERATIONAL OVERVIEW
1-6
1.7 MOB Mark
1.7.1 Entering the MOB mark, setting MOB as destination
The MOB (Man Overboard) mark functions to mark man overboard position. You
can inscribe this mark from any mode.
Man
overboad
Range, bearing
Current
position
MOB
mark
MOB
MOB
162.5°M
0.49 nm
MOB information
Distance and range
to MOB position
MOB concept
1. Press and hold down the [MOB/WPT] key immediately for about three
seconds when someone falls onboard, to show the display below.
MAN OVER BOARD!
Set (MOB) as destination?
YES NO
MOB message window
2. Confirm that YES is selected, and then press the [ENTER] knob to set the
MOB position as the destination. (Choose NO to mark position as a
waypoint.)
If you select the MOB position as the destination, the MOB ALARM window
appears. Push the [ENTER] knob to erase it and then the following message
appears on the display.
MOB ALARM
MOB function is activated
MOB ALARM window
Distance and bearing to the MOB position are shown in the MOB data box when
the cursor is placed on the MOB mark.
MOB
FIX
DST
BRG
33 07. 674N
132 51. 766W
1.14 nm
187 M
MOB data box
1. OPERATIONAL OVERVIEW
1-7
1.7.2 Deleting the MOB mark
1. Operate the cursor pad to place the cursor on the MOB mark, and then press
the STOP soft key to cancel the navigation to the MOB mark.
2. Press the DELETE soft key to show the confirmation window.
3. Choose “YES”, and then press the [ENTER] knob to delete the MOB mark.
The color of MOB mark changes to blue. After changing the range, the MOB
mark is cleared completely.
1.8 Menu Operation
Most operations are carried out from the menu bar. The menu bar is opened or
closed with the [MENU] key. Menus and options may be selected by rotating the
[ENTER] knob or operating the cursor pad. However, this manual describes
operating procedure using the [ENTER] knob.
Using the [ENTER] knob
1. Press the [MENU] key to show the menu bar.
Menu Bar
GENERAL PLOTTER MAP ALARMS ADVANCED INFO FIND
Menu bar
2. Rotate the [ENTER] knob to choose a menu title and then push the [ENTER]
knob to show the menu.
For example, choose GENERAL to display the GENERAL menu.
LANGUAGE English
KEYPAD BEEP Off
PALETTE Normal
TIME LINE Infinite
TIME REFERENCE UTC
TIME FORMAT 12hour
DATE FORMAT MM-DD-YY
AUTO INFO On All
SHIP ICON
WIND GRAPH True
UNITS OF MEASURE
General menu
3. Rotate the [ENTER] knob to choose an item and then push the [ENTER]
knob.
For example, choose LANGUAGE.
1. OPERATIONAL OVERVIEW
1-8
English
Italiano
Francais
Deutsch
Espanol
Norsk
Svensk
Portuguese
Language option window
4. Rotate the [ENTER] knob to choose the option desired and then press the
[ENTER] knob.
To cancel, press the [CLEAR] key.
5. To close all menus and option windows, press the [MENU] key.
To close option windows one by one, press the [CLEAR] key.
Using the cursor pad
1. Press the [MENU] key to show the menu bar.
Menu Bar
GENERAL PLOTTER MAP ALARMS ADVANCED INFO FIND
Menu bar
2. Press or on the cursor pad to choose a menu title and then press to
show the corresponding menu.
For example, choose GENERAL to display the GENERAL menu.
LANGUAGE English
KEYPAD BEEP Off
PALETTE Normal
TIME LINE Infinite
TIME REFERENCE UTC
TIME FORMAT 12hour
DATE FORMAT MM-DD-YY
AUTO INFO On All
SHIP ICON
WIND GRAPH True
UNITS OF MEASURE
General menu
3. Press to choose an item and then press to show its option window.
For example, choose LANGUAGE.
1. OPERATIONAL OVERVIEW
1-9
English
Italiano
Francais
Deutsch
Espanol
Norsk
Svensk
Portuguese
Language option window
4. Press to choose an option and then press to close the window.
To cancel, press .
5. To close all menus and option windows, press the [MENU] key.
To close option windows one by one, press the [CLEAR] key.
1.9 Simulation Mode
The simulation mode, which is for use by service technicians for demonstration
purposes, provides simulated operation to help acquaint users with the functions
of the unit. All keys are operative.
“SIMUL” appears at the bottom of the display when the simulation mode is
active.
Plotter
Own ship’s mark moves from the default or selected position at the speed and
course set.
1. Press the [MENU] key to display the menu bar.
2. Rotate the [ENTER] knob to choose ADVANCED and then push the [ENTER]
knob.
3. Rotate the [ENTER] knob to choose GPS SIMULATION and then push the
[ENTER] knob to show the following window.
SIMULATION MODE On
COURSE 007 M
SPEED 001.0 Kts
DATE Apr/02/04
TIME 12:00:00 AM
CURSOR CONTROL Off
GPS simulation window
4. Rotate the [ENTER] knob to choose SIMULATION MODE and then push the
[ENTER] knob.
5. Rotate the [ENTER] knob to choose On and then push the [ENTER] knob.
6. Rotate the [ENTER] knob to choose COURSE and then push the [ENTER]
knob.
7. Enter the course (Setting range: 0 to 359) by rotating the [ENTER] knob,
pressing the or , and then press the SAVE soft key.
1. OPERATIONAL OVERVIEW
1-10
Note: You can return the value to zero by pressing the CLR FLD soft key.
8. Enter SPEED, DATE and TIME.
9. Rotate the [ENTER] knob to choose CURSOR CONTROL and then push the
[ENTER] knob.
10. Rotate the [ENTER] knob to choose On or Off as appropriate and then push
the [ENTER] knob.
When On is selected, you can set course value ( ) and speed value ( )
on the simulation plotter display.
When you select On, the cursor does not appear on the plotter menu.
11. Rotate the [ENTER] knob to choose SELECT POSITION and then push the
[ENTER] knob.
The plotter display appears.
12. Operate the cursor pad to place the cursor at the desired starting point.
13. Push the [ENTER] knob to move the own ship mark on the cursor.
14. Press the [CLEAR] key.
Echo sounder
1. Press the [MENU] key to show the menu bar on the plotter display.
2. Rotate the [ENTER] knob to choose ADVANCE and then push the [ENTER]
knob.
3. Rotate the [ENTER] knob to choose ECHO SOUNDER SIMULATION and
then push the [ENTER] knob.
4. Rotate the [ENTER] knob to choose On and then push the [ENTER] knob.
5. Press the [MENU] key to close the menu.
6. Choose the sounder display on the display mode screen.
2-1
2. PLOTTER DISPLAYS
2.1 Presentation Modes
The plotter display mainly shows chart, ship’s track, waypoints, and navigation
data.
Three types of display presentations are provided for the normal plotter display:
north-up, course-up and auto course-up. To change the mode, use the
presentation mode selection soft key, which is the leftmost soft key.
2.1.1 North-up
1. Press any soft key to show the soft key labels.
2. Press the NORTH UP soft key to show the north-up display. North (zero
degree) is at the top of the display.
When the cursor is on, the own ship moves and the chart is fixed. (True motion)
When the cursor is off, the chart, waypoints and other marks move and own ship
is fixed. (Relative motion)
To turn the cursor off, press the CENTER soft key.
0001WPT
GPSW2D
NORTH UP
1 nm
Track
GPS status
Current display mode
(north-up)
Icons
Range scale
Waypoint
Course bar
Own ship marker
Plotter display, north-up mode
2. PLOTTER DISPLAY
2-2
2.1.2 Course-up
Press the COURSE UP soft key to show the course-up display. When
destination is set, it is at the top of the screen and the north mark appears at the
upper right side of the screen and points to north.
When destination is not set, the course is upward on the screen at the moment
the course-up mode is selected.
0001WP
1
nm
COURSE UP CENTER
MAP SETUP
SEARCH
N
NAVDATA OFF
Plotter display, course-up mode
2.1.3 Auto course-up
Press the AUTO CSE UP soft key to show the automatic course-up display. The
course or heading is at the top of screen at the moment the auto course-up
mode is selected. When own ship is off its intended course by 30º (default
setting, this degree can be changed on NAVIGATION menu. For details, see
chapter 8.) or more, it is automatically brought back to perpendicular.
0001WP
1 nm
AUTO CSE UP CENTER
MAP SETUP
N
SEARCH NAVDATA OFF
Plotter display, auto course-up mode
2. PLOTTER DISPLAY
2-3
2.2 Cursor
2.2.1 Turning on the cursor, shifting the cursor
Press the cursor pad to turn the cursor on, and the cursor appears at the own
ship’s position. Operate the cursor pad to shift the cursor. The cursor moves in
the direction of the arrow or diagonal pressed on the cursor pad.
Cursor state determines what data is shown in the NAVDATA window. This
window can be enabled or disabled by pressing the NAVDATA ON soft key.
NAVDATA window
Also, when the cursor is placed on own ships position, its data is shown as
follows.
FIX 3D
SOG COG
33 37.125N
118 48.428W
1.00 kts 007 M
Own ship’s position data window
2.2.2 Moving the cursor to the center of the screen
Press the CENTER soft key to return the cursor to the screen center.
2. PLOTTER DISPLAY
2-4
2.2.3 Displaying data
Besides its fundamental functions of providing position data, the cursor can also
provide data for chosen caution area, depth area, source of data, etc. Further,
you can display information about an icon by placing the cursor on it.
1. Press the cursor pad to turn the cursor on.
2. Use the cursor pad to place the cursor on the position desired.
The object information window appears.
Object Info
Wreck
Object information window (ex. wreck)
3. If you want to know more details, press the Details soft key.
Objects
Wreck
Category of wreck
non-dangerous wreck
Water level effect
always under water/submerged
Wreck
Caution area
Depth area
Military practice area
Sea area
Source of data
Object detail window (ex. wreck)
4. Rotate the [ENTER] knob to choose the item you want to know more about.
Detailed information appears in the lower column.
5. Press the [CLEAR] key to close the window.
2.3 Selecting Chart Scale/Range
Chart scale (range) may be selected with the [RANGE] key. The [RANGE +] key
zooms in the chart; [RANGE -] key zooms out it.
2. PLOTTER DISPLAY
2-5
2.4 Navigation Data Display
The navigation data display provides generic navigation data, and it is shown in
combination displays.
Appropriate sensors are required. Bars (- -) appear when corresponding sensor
is not connected.
LATITUDE
22º
03
.7
30
N
LONGITUDE
1
3
5
7.
8
7
0
E
SOG
12.0KT
S
COG
7
º
M
TRIP
111.5 nm
TEMP
10.3
º
F
TIME
12:2
8
AM
DATE
Apr/17/04
DEPTH
22.5 Ft
Position
Trip meter
Speed
Course
Depth
Temperature
Navigation data display
2. PLOTTER DISPLAY
2-6
2.5 Compass Display
The compass display, shown in combination displays, provides steering
information. The compass rose shows two triangles: the red triangle shows own
ship’s course and the black triangle, which moves with ship’s course, shows the
bearing to destination waypoint.
The water temperature and depth graphs, which require appropriate sensors,
shows the latest 10 minutes of water temperature and depth data.
DEST:
0001WP
DST:
305.3
nm
SOG
12.0
Kts
TTG:25:26
ETA:12:28AM
DPT
45.6ft
TMP
40.4ºF
155º
STW:
12.4
KTS
N
w
E
Ship's course
(red)
Water temperature
graph*
Shown (in green)
when direction to
steer is "right."
XTE monitor
(See below for
description.)
Shown (in red)
when direstion to
steer is "left".
Depth
graph*
Destination
waypoint
bearing
(black)
Time-to-go
to destination
Own ship marker
(Yellow)
Destination
waypoint
Speed
through
water
Range to destination waypoint
Speed over ground
Bearing scale
Estimated time of
arrival at destination
0.5 0.5
Compass distance
Reading the XTE (cross-track error) monitor
The XTE monitor, located below the compass rose, shows the distance you are
off course and the direction to steer to return to course. The own ship marker in
the monitor moves according to direction and distance off course. An arrow
appears at the right or left side of the XTE monitor and it shows the direction to
steer to return to intended course. It is shown in red when you should steer left,
and green when you should steer right. In the example above you would steer
left to return to course. To maintain course, steer the vessel so the own ship
marker stays at the center of the XTE monitor. Note that the XTE range can be
changed by rotating the [ENTER] knob.
2. PLOTTER DISPLAY
2-7
2.6 Highway Display
The highway display, shown in combination display with the plotter screen,
provides a graphic presentation of ship’s track along intended course. It is useful
for monitoring ship’s progress toward a waypoint. The own ship marker shows
the relation between your vessel and intended course.
TIME
12:28AM
SOG
12.0KTs
COG
044º
Turn knob to change scale: 0.2nm
Course
Speed
Current time
Own ship marker
Intended course
Destination waypoint
(Flag)
Bearing of
destination
waypoint
Highway display
Changing the scale
You can change the scale of the highway display to 0.2, 0.5, 1.0, 2.0, 4.0 or 10.0
(nm). Rotate the [ENTER] knob to change it. Note that the available range
depends on own ship’s position.
2. PLOTTER DISPLAY
2-8
2.7 GPS Status Display
The GPS status display provides data on the GPS satellites.
33 18.426N
12:09 AM
1.00
Apr/02/04
ACQUIRING
LONGITUDE
LATITUDE
HDOP
SOG Kts
DATE
TIME
131 48.608W
12.5
07 14 25 31 -- --
01 11 20 28 -- --
07
01
11
14
25
31
28
Position
DOP value
Receive signal level:
Bars show satellite
signal level. Satellites
in brown are used in
fixing position.
Estimated position in the sky,
and satellite number in brown circle
is used for positioning.
GPS status display
2. PLOTTER DISPLAY
2-9
2.8 Celestial Display
Your plotter provides for calculation of the tide heights for any date. Additionally it
displays the time of sunrise, sunset, moonrise and moonset.
ENTER to change Date - Turn the KNOB to set [DLS/STANDARD] time
Nearest Tide Station:
High Water
Low Water
From tide
Sunrise:
Sunset:
Moonrise:
Moonset:
Date
Time
- - - - -
- - - - -
- -.- - nm
03:50 PM U
01:49 AM U
10:29 AM U
10:07 PM U
- . - - ft
- . - - ft
- - - M
Moon phase
50%
33 20. 435N
131 48.608W
April-01-2004
02:35
Tide, celestial display
Setting the date for calculation
1. Press the [ENTER] knob to show the date window.
MM-DD-YY
04/09/04
Date window
2. Press the cursor pad to move the cursor, and then rotate the [ENTER] knob
to choose the date.
When you want to clear all values, press the CLR FLD soft key.
To escape, press the CANCEL soft key.
3. Press the SAVE soft key to set.
Tide, Celestial Display
2. PLOTTER DISPLAY
2-10
2.9 Graph Display
Four graphs can be displayed alternately on the half-screen of the LCD: depth,
wind, water temperature and SOG (speed).
Press the GRAPH TYPE soft key to choose display graphs in the sequence
shown below.
Note: Appropriate sensors required to display graphs.
Depth Graph Page 1 of 4
40.2
30.2
20.2
10.2
03:33
03:34 03:35
Depth graph
Wind Graph Page 2 of 4
1.2
2.2
3.2
4.2
03:33
03:34 03:35
Wind graph
Water Temp. Graph Page 3 of 4
66.2
67.2
68.2
69.2
03:33
03:34 03:35
Water temperature graph
SOG Graph Page 4 of 4
0.5
0.7
1.0
1.2
03:33
03:34 03:35
Depth graph
1.0 kts
9.6 Ft
3.1 knot
67.4 F
GRAPH TYPE
soft key
GRAPH TYPE
soft key
GRAPH TYPE
soft key
GRAPH TYPE
soft key
Sequence of graph display
2. PLOTTER DISPLAY
2-11
2.10 Wind Display
Your plotter can show the graphical wind indicator when the appropriate data is
input.
WIND
TRUE
HEAD
7º M
- - -
- - -
Kts
0
30
60
90
120
150
180
150
120
90
60
30
Wind display
Selecting the wind direction indication format
The wind direction can be selected to true or apparent.
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose GENERAL and then push the [ENTER]
knob.
3. Rotate the [ENTER] knob to choose WIND GRAPH and then push the
[ENTER] knob.
4. Rotate the [ENTER] knob to select True or Apparent as appropriate.
True: The Speed and direction (relative to due north)
Apparent: The direction (in relation to ship’s bow) and speed of the wind as it
appears to those on board, relative to the speed and direction of the
boat; combination of the true wind and the wind caused by the boat’s
movement.
5. Push the [ENTER] knob.
6. Press the [MENU] key to close the menu.
2. PLOTTER DISPLAY
2-12
This page is intentionally left blank.
3-1
3. TRACK
Your ship’s track is plotted on the screen using navigation data fed from the
internal GPS navigator. This chapter shows you what you can do with track, from
turning it on or off to changing its plotting interval. In the default setting, own
ship’s track is turned on and is displayed in black.
3.1 Selecting Active Track
Your plotter can plot up to five track lines. It can be useful to have multiple track
lines to distinguish tracks according to date or course. Note that other
track-related settings are available for the track chosen here.
1. Press the [MENU] key to show the menu bar.
Menu Bar
GENERAL PLOTTER MAP ALARMS ADVANCED INFO FIND
Menu bar
2. Rotate the [ENTER] knob to choose PLOTTER from the menu bar.
3. Push the [ENTER] knob to show the PLOTTER menu.
TRACK
ROUTES
WAYPOINTS
MEMORY CARD
Plotter menu
4. Rotate the [ENTER] knob to choose TRACK and then push the [ENTER]
knob.
TRACKING OffNAVIGATE
ACTIVE TRACK 1
VISIBLE On
LINE COLOR
DELETE
STEP UNIT Dist
DISTANCE 0.1 Nm
TIME 1 min
Track menu
3. TRACK
3-2
5. Rotate the [ENTER] knob to choose ACTIVE TRACK and then push the
[ENTER] knob.
6. Rotate the [ENTER] knob to choose the desired number of own ship tracks to
use, from among 1 to 5.
7. Press the SAVE soft key.
8. Press the [MENU] key to close the menu.
3.2 Displaying Track
To display track line on the screen, do the following.
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose PLOTTER from the menu bar and then
push the [ENTER] knob.
3. Rotate the [ENTER] knob to choose TRACK and then push the [ENTER]
knob.
4. Rotate the [ENTER] knob to choose TRACKING and then push the [ENTER]
knob.
5. Rotate the [ENTER] knob to select On and then push the [ENTER] knob.
To turn off the track display, select Off here.
6. Press the [MENU] key to close the menu.
3.3 Changing Track Color
Track can be displayed in black (default setting), light-green, red, purple, yellow,
gray, brown and dark green. It can be useful to change track color on a regular
basis to discriminate the active tracks.
1. Choose TRACK from the PLOTTER menu and then push the [ENTER] knob.
2. Choose LINE COLOR and then push the [ENTER] knob.
3. Rotate the [ENTER] knob to choose the color desired and then push the
[ENTER] knob.
4. Press the [MENU] key to close the menu.
3.4 Stopping, Restarting Plotting
When your boat is at anchor or returning to port, you probably won’t need to
record its track. You can stop recording the track, to conserve the track memory,
as below.
1. Choose TRACK from the PLOTTER menu and then push the [ENTER] knob.
2. Choose TRACKING and then push the [ENTER] knob.
3. Rotate the [ENTER] knob to choose Off, and then push the [ENTER] knob.
3. TRACK
3-3
3.5 Hiding the Track
The track lines can be hidden (but recorded). This function is useful when there
are too many tracks to distinguish on the screen and it is hard to distinguish one
from another.
1. Choose TRACK from the PLOTTER menu and then push the [ENTER] knob.
2. Choose VISIBLE and then push the [ENTER] knob.
3. Rotate the [ENTER] knob to select On.
To re-display the track, choose Off.
4. Press the [MENU] key to close the menu.
3.6 Track Plotting Method and Interval
In drawing the own ship track, first the ship’s position fed from the internal GPS
navigator is stored into the unit’s memory at an interval of time or distance. A
shorter interval provides for better reconstruction of the track, but the storage
time of the track is reduced. When the track memory becomes full, the oldest
track is erased to make room for the latest.
3.6.1 Track plotting method
Track may be plotted by time or distance.
1. Choose TRACK from the PLOTTER menu.
2. Choose STEP UNIT and then push the [ENTER] knob.
Dist
Time
STEP UNIT window
3. Rotate the [ENTER] knob to select Dist (distance) or Time as appropriate.
Distance is useful for conserving track memory, since no track is recorded when
the boat is stationary.
4. Push the [ENTER] knob.
5. Press the [MENU] key to close the menu.
3. TRACK
3-4
3.6.2 Track plotting interval
1. Choose TRACK from the PLOTTER menu.
2. Choose DISTANCE or TIME as appropriate and then push the [ENTER]
knob.
0.01
0.05
0.1
0.5
1.0
2.0
5.0
10.0
1sec
5 sec
10 sec
30 sec
1 min
5 min
10 min
30 min
1 h
Distance window Time window
Interval windows
3. Rotate the [ENTER] knob to select setting.
4. Push the [ENTER] knob.
5. Press the [MENU] key to close the menu.
3.7 Erasing Track
This section shows you how to erase the active track.
1. Choose TRACK from the PLOTTER menu.
2. Choose DELETE and then push the [ENTER] knob.
WARNING
Delete Track
Are you sure?
YES NO
Delete window
3. Push the [ENTER] knob to erase the track.
To cancel, rotate the [ENTER] knob to choose NO and then push the [ENTER]
knob.
4. Press the [MENU] key.
4-1
4. WAYPOINT
In navigation terminology, a waypoint is a particular location on a voyage
whether it be a starting, intermediate or destination point. A waypoint is the
simplest piece of information your equipment requires to get you to a destination,
in the shortest distance possible.
This unit has 2,000 waypoints into which you can enter position information. You
may enter a waypoint four ways: at own ship position, by cursor, at MOB position
(see chapter 1) and through the waypoint list (manual input of latitude and
longitude).
4.1 Entering Waypoints
4.1.1 Entering a waypoint at own ship position or cursor position
Turn the cursor off to enter a waypoint at own ship position, or turn it on to enter
a waypoint at cursor position.
A newly entered waypoint is saved to the waypoint list, under the youngest
empty waypoint number.
1. Press the [MOB/ WPT] key momentarily to store your position as a waypoint.
When the cursor is displayed, the waypoint is entered at the cursor position.
The new waypoint window appears and it shows waypoint name, position of
waypoint, waypoint mark shape, waypoint name and comment for newly entered
waypoint.
NAME
0004WP
LATITUDE/LONGITUDE
47 56.307N
133 56.807W
SHAPE
COLOR
COMMENT
00:29 APR0204
Waypoint window
2. If you do not need to change the waypoint data, press the SAVE soft key to
register the waypoint. The steps which follow show you how to change
waypoint data.
3. NAME is selected; push the [ENTER] knob.
4. WAYPOINT
4-2
4. Rotate the [ENTER] knob to choose the desired alphanumeric character.
You can clear all digits in the field by pressing the CLR FLD soft key.
5. Press to move the cursor to the next digit, and then rotate the [ENTER]
knob to choose the character desired.
6. Repeat steps 4 and 5 to complete the name. (Max. 10 characters)
7. Press the SAVE soft key and then rotate the [ENTER] knob to choose the
LATITUDE/LONGITUDE section.
8. Push the [ENTER] knob.
9. Use the cursor pad and [ENTER] knob to enter latitude data, and then press
the SAVE soft key.
10. Use the cursor pad and [ENTER] knob to enter longitude data, and then
press the SAVE soft key.
11. Rotate the [ENTER] knob to choose “SHAPE” in the SHAPE/COLOR section.
12. Push the [ENTER] knob to show the waypoint mark shape selection window.
Waypoint mark shape selection window
13. Rotate the [ENTER] knob to choose shape desired.
14. Push the [ENTER] knob.
15. Rotate the [ENTER] knob to choose “COLOR” and then push the [ENTER]
knob.
Waypoint mark color selection window
16. Rotate the [ENTER] knob to choose the color desired, then push the
[ENTER] knob.
17. Rotate the [ENTER] knob to choose COMMENT section and then push the
[ENTER] knob.
18. Use the cursor pad and [ENTER] knob to enter a comment. (Max. 13
characters)
19. Press the SAVE soft key twice to register the waypoint.
4. WAYPOINT
4-3
4.1.2 Entering a waypoint from the waypoint list
You can manually enter waypoint position from the waypoint list as follows.
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose PLOTTER and then push the [ENTER]
knob to show the PLOTTER menu.
TRACK
ROUTE
WAYPOINT
MEMORY CARD
Plotter menu
3. Rotate the [ENTER] knob to choose WAYPOINTS and then push the
[ENTER] knob.
The WAYPOINT LIST is displayed.
WAYPOINT LIST
SYM TYPE
MODE
DST [nm}
BRG [M]
LATITUDE
LONGITUDE
ICON SEARCH PLOT EDIT NEW
MODE DELETE SORT SEND RECEIVE
NAME
COMMENT
0001WP
00:58 MAY3104
WPT
34 34. 641 N
135 09. 912 E
6.669
045
SHOWN
Waypoint list
4. Rotate the [ENTER] knob to choose NEW at the bottom of the screen and
then push the [ENTER] knob.
The new waypoint is entered at the current own ship position. (When cursor is
turned on, it is entered at the cursor position.)
5. If desired, change waypoint data; choose EDIT (at the bottom of screen) and
follow the paragraph 4.2.
6. Press the [CLEAR] key to close the WAYPOINT LIST.
Note 1: The WAYPOINT LIST can also be shown by pressing the WPT/QWP
soft key, which is shown when the cursor is placed on a waypoint.
Note 2: You can change the page of the WAYPOINT LIST by pressing or .
4. WAYPOINT
4-4
4.2 Editing Waypoint Data
Waypoint data may be edited from the waypoint list or directly from the plotter
display.
4.2.1 Editing waypoint data from the waypoint list
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose PLOTTER and then push the [ENTER]
knob.
3. Rotate the [ENTER] knob to choose WAYPOINTS and then push the
[ENTER] knob to show the WAYPOINT LIST.
4. Press the cursor pad (▲▼) to choose the waypoint you want to edit.
5. Rotate the [ENTER] knob to choose EDIT at the bottom of screen.
6. Push the [ENTER] knob.
7. Press the cursor pad (◄►) to place the cursor on the appropriate column,
and then push the [ENTER] knob.
8. Edit data as appropriate, and then push the [ENTER] knob.
9. Press the [CLEAR] key to close the list.
4.2.2 Editing a waypoint from the plotter display
You may edit waypoints from the plotter display two ways: from the waypoint
window or directly on the plotter display.
From waypoint window
1. Operate the cursor pad to place the cursor on the waypoint you want to edit.
2. Press the EDIT soft key to show the waypoint window.
NAME
0004WP
LATITUDE/LONGITUDE
47 56.307N
133 56.807W
SHAPE
COLOR
COMMENT
00:29 APR0204
Waypoint window
3. Edit data as appropriate referring to paragraph 4.1.1, and then press the
SAVE soft key.
Directly on plotter display
Operate the cursor pad to place the cursor on the waypoint to edit, and then
press the MOVE soft key. The color of the selected waypoint changes to blue,
and red line runs between it and the cursor. Operate the cursor pad to select the
new position, and then push the [ENTER] knob.
4. WAYPOINT
4-5
4.3 Erasing Waypoints
Waypoints can be erased from the waypoint list or directly from the plotter
display.
4.3.1 Erasing a waypoint directly from the plotter display
1. Press the cursor pad to place the cursor on the waypoint you want to delete.
2. Press the DELETE soft key.
The following window appears.
WARNING
Delete 0001WP
Are you sure?
YES NO
3. Push the [ENTER] knob.
The color of the selected waypoint at step 1 changes to blue.
4.3.2 Erasing a waypoint from the waypoint list
1. Press the [MENU] key to show the menu bar.
2. Choose WAYPOINTS from the PLOTTER menu, and then push the [ENTER]
knob to show the WAYPOINT LIST.
3. Press the cursor pad (▲▼) to choose the waypoint you want to delete.
4. Rotate the [ENTER] knob to choose DELETE at the bottom of screen, and
then push the [ENTER] knob.
MODE
DELETE SELECTED
DELETE ALL
5. Rotate the [ENTER] knob to select DELETE SELECTED, and then push the
[ENTER] knob.
If you want to delete all waypoints in the list, choose DELETE ALL.
WARNING
Delete points
Are you sure?
YES NO
6. You are asked if you are sure to delete selected waypoint (s). Push the
[ENTER] knob to delete, or choose NO and push the [ENTER] knob to
escape.
7. Press the [CLEAR] key to finish.
4. WAYPOINT
4-6
4.4 Searching, Sorting Waypoints
You can search and sort waypoints on the waypoint list as follows.
Searching by waypoint name
1. Open the WAYPOINT LIST.
2. Rotate the [ENTER] knob to choose SEARCH at the bottom of the screen.
3. Push the [ENTER] knob.
4. Enter the waypoint name you want to find, and then press the SAVE soft key.
The cursor moves on the chosen waypoint name on the list.
5. Press the [CLEAR] key to close the list.
Sorting waypoints
1. Open the WAYPOINT LIST.
2. Rotate the [ENTER] knob to choose SORT at the bottom of the screen.
3. Push the [ENTER] knob to show the item window.
A-Z ASCENDING
Z-A DESCENDING
DISTANCE ASC
DISTANCE DESC
Sort window
4. Rotate the [ENTER] knob to choose a sorting method.
A-Z ASCENDING: Sorting waypoints in ascending alphanumeric order.
Z-A DESCENDING: Sorting waypoint in descending alphanumeric order.
DISTANCE ASC: Sorting waypoints in order of decreasing distance to own ship.
DISTANCE DESC: Sorting waypoints in order of increasing distance to own ship.
5. Push the [ENTER] knob.
6. Press the [CLEAR] key to close the list.
4. WAYPOINT
4-7
4.5 Other Waypoint List Functions
This section shows you how to execute the various functions available on the
WAYPOINT LIST.
4.5.1 Filtering waypoints by mark shape
You may filter waypoints in the waypoint list by mark shape. This is useful when
you are looking for waypoints of a specific shape.
1. Open the WAYPOINT LIST.
2. Rotate the [ENTER] knob to choose ICON at the bottom of screen.
3. Push the [ENTER] knob to show the ICON window.
ICON
SELECT
ALL
Icon window
4. Rotate the [ENTER] knob to choose SELECT and then push the [ENTER]
knob.
The waypoint mark shape selection window appears.
Waypoint mark shape selection window
Note: ALL shows all waypoints.
5. Rotate the [ENTER] knob to choose the mark shape corresponding to the
waypoint on the list, and then push the [ENTER] knob.
6. Press the [CLEAR] key twice to close the list.
To display all waypoints, choose ALL at step 4 and then press the [CLEAR] key
twice.
4. WAYPOINT
4-8
4.5.2 Hiding or showing waypoints
Waypoints can be shown or hidden individually or collectively on the plotter
display as below.
1. Open the WAYPOINT LIST.
2. Press the cursor pad (▲▼) to choose the waypoint you want to show or
hide.
All waypoints can also be shown or hidden.
3. Rotate the [ENTER] knob to choose MODE at the bottom of screen, and then
push the [ENTER] knob.
MODE
SHOW
ICON
HIDE
SHOW ALL
ICON ALL
HIDE ALL
Mode window
4. Rotate the [ENTER] knob to choose option desired.
SHOW: Shows the name and mark of the waypoint selected at step 2.
ICON: Shows only the mark of the waypoint selected at step 2.
HIDE: Hides the name and mark of the waypoint selected at step 2.
SHOW ALL: Shows the names and marks of all waypoints.
ICON ALL: Shows only marks of all waypoints.
HIDE ALL: Hides the names and marks of all waypoints.
5. Push the [ENTER] knob.
6. Press the [CLEAR] key to close the menu.
4.5.3 Searching waypoints
You can search for waypoint by name as follows.
1. Open the WAYPOINT LIST.
2. Press the cursor pad (▲▼) to choose the waypoint desired.
3. Choose PLOT at the bottom of the screen.
4. Push the [ENTER] knob.
The plotter display appears with the waypoint chosen at step 2 at the screen
center.
5-1
5. ROUTE
Often a trip from one place to another involves several course changes,
requiring a series of route points (waypoints) which you navigate to, one after
another. The sequence of waypoints leading to the ultimate destination is called
a route.
5.1 Entering Routes
You can store up to 200 routes and a route may contain up to 35 points.
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose PLOTTER and then push the [ENTER]
knob to show the PLOTTER menu.
TRACK
ROUTES
WAYPOINTS
MEMORY CARD
Plotter menu
3. Rotate the [ENTER] knob to choose ROUTES and then push the [ENTER]
knob to show the route list.
Note: The route list can also be shown by placing the cursor on a waypoint
and then pressing the ROUTE LIST soft key.
N NAME COMMENT LENGTH
WAYPOINTS
FIND NEW EDIT RENAME COMMENT
PLOT DELETE REVERSE COLOR SEARCH
SEND RECEIVE CONNECT SELECT REPORT
ROUTE LIST
1 0001RT 00:10 MAY3104 1.901 nm 3
Route list
4. Rotate the [ENTER] knob to choose NEW at the bottom of screen and then
push the [ENTER] knob to show the new route menu.
The new route is automatically named with the youngest empty route number
and current date is used as the comment. Name and comment may be changed
if desired.
6. ROUTE
5-2
CANCEL
COORD TYPE
SAVE
1
34 41.895 N
135 21.109 ’W
34 43.776 N
135 17.883 W
34 46.007 N
135 19.521 W
34 80.398 N
135 35.354 W
34 28.361 N
135 49.239 W
34 24.242 N
135 46.753 W
LEG
ROUTE NAME:0001RT______
COMMENT : 17:33_ JUL1003
SKIP
00 73WP______
14:09_APR0403
0001WP______
09:21_JAN1903
NISHINOMIYA_
10:34_JAN1903
0008WP______
15:07_JAN1903
0018WP______
16:49_APR0103
0022WP______
11:12_APR0603
Route name and
comment
Range between two waypoints
Push [MENU] key to execute.
SORT SEARCH
DELETE
New route menu
5. Rotate the [ENTER] knob to choose a waypoint, and then push the [ENTER]
knob.
6. Choose the waypoints in the sequence you want to follow them.
You can find waypoints by using the SORT or SEARCH function.
Choose SORT or SEARCH at the bottom right-hand side of the screen as
appropriate and then press the [MENU] key.
SORT: Sorting waypoints distance (ascending or descending) or alphabetical
(ascending or descending).
SEARCH: Enter the waypoint name desired.
7. Press the SAVE soft key to register the route.
8. Press the [CLEAR] key to close the list.
5.2 Changing the Route Name/Comment
You can change the route name or comment as follows:
1. Open the route list.
2. Press the cursor pad (▲▼) to choose the route you want to edit.
3. Rotate the [ENTER] knob to choose RENAME at the bottom of screen and
then push the [ENTER] knob.
To change comments, choose COMMENT and then push the [ENTER] knob.
4. Edit the route name as appropriate.
Press the cursor pad to move the digit cursor.
5. Press the SAVE soft key.
6. Press the [CLEAR] key to close the list.
5. ROUTE
5-3
5.3 Connecting Routes
Two routes which you have created can be connected as follows to form a new
route.
1. Open the route menu.
2. Rotate the [ENTER] knob to choose CONNECT at the bottom of screen and
then push the [ENTER] knob.
The connect route menu appears.
CONNECT
ROUTE
CANCELFORW<->RVRS SEARCH NAME SAVE
LENGTH 3.07 nm
WAYPOINTS 25
LENGTH 3.07 nm
WAYPOINTS 25
LENGTH 3.07 nm
WAYPOINTS 25
LENGTH 3.07 nm
WAYPOINTS 25
LENGTH 3.07 nm
WAYPOINTS 25
_ _ _ _ _ _ _ _ _ _ _ _
_
_ _ _ _ _ _ _ _ _ _ _
SET ROUTE
0001RT______
09:21_JAN1903
0002RT______
15:07_JAN1903
0003RT______
16:49_APR0103
0004RT______
14:09_JUL0203
0005RT______
14:27_JUL0203
FIRST
FORWARD
SECOND
FORWARD
SORT
Push [MENU] key to execute
Connect route menu
3. Rotate the [ENTER] knob to choose the first route and then push the
[ENTER] knob.
The selected route name is shown in the “FIRST” window.
4. Press the FORW <-> RVRS soft key to select the direction to follow the
waypoints of the route, forward or reverse.
5. Press to place the cursor on the “SECOND” window.
6. Rotate the [ENTER] knob to choose the second route, and then push the
[ENTER] knob.
7. Press the SAVE soft key.
8. Press the [CLEAR] key twice to close the menu.
Note: The maximum number of waypoints in a route is 35. If this number is
exceeded an error message appears. In this case, delete waypoints in one
or both routes so the total number of waypoints does not exceed 35.
6. ROUTE
5-4
5.4 Inserting Waypoints
Waypoints can be inserted in a route as follows:
Inserting a waypoint from the route list
1. Show the route list.
2. Press the cursor pad (▲▼) to choose a route.
3. Rotate the [ENTER] knob to choose EDIT at the bottom of screen and then
push the [ENTER] knob to show the route menu.
CANCEL
COORD TYPE
SAVE
1
34 41.895 N
135 21.109 W
34 43.776 N
135 17.883 W
34 46.007 N
135 19.521 W
34 80.398 N
135 35.354 W
34 28.361 N
135 49.239 W
34 24.242 N
135 46.753 W
LEG
ROUTE NAME:0001RT______
COMMENT : 17:33_ JUL1003
SKIP
00 73WP______
14:09_APR0403
0001WP______
09:21_JAN1903
NISHINOMIYA_
10:34_JAN1903
0008WP______
15:07_JAN1903
0018WP______
16:49_APR0103
0022WP______
11:12_APR0603
Route name and
comment
Range between two waypoints
Push [MENU] key to execute.
SORT SEARCH
DELETE
Route menu
4. Press the cursor pad (▲▼) to place the cursor at the location where you
want to insert a waypoint.
5. Rotate the [ENTER] knob to choose the waypoint you want to insert. (You
can search for a waypoint by the SORT or SEARCH function.)
6. Push the [ENTER] knob to enter the waypoint.
7. Press the SAVE soft key to close the route menu.
8. Press the [CLEAR] key to close the route list.
5. ROUTE
5-5
Inserting a waypoint from the plotter display
You can insert a waypoint in a route directly on the screen.
1. Press the cursor pad to place the cursor on a line connecting waypoints in a
route.
The window below appears.
ROUTE: 1 [0001RT]
0001WP - 0002WP
DST: 4.74 nm
BRG: 102 M
Leg window (ex.)
2. Press the INSERT soft key.
The selected line (dashed) turns red.
3. Operate the cursor pad to place the cursor on an existing waypoint and then
push the [ENTER] knob.
4. Press the SAVE soft key.
The route is then redrawn to include the newly inserted waypoint.
5.5 Removing Waypoints from a Route
Removing a waypoint from the route list
1. Show the route list.
2. Press the cursor pad (▲▼) to choose a route.
3. Rotate the [ENTER] knob to select EDIT at the bottom of screen and then
push the [ENTER] knob to show the route menu.
4. Press the cursor pad (▲▼) to choose the waypoint you want to remove.
5. Press the DELETE soft key.
6. Press the SAVE soft key.
7. Press the [CLEAR] key to close the list.
Removing a waypoint from the plotter display
1. Press the cursor to place the cursor on the waypoint you want to remove
from a route.
2. Press the DELETE soft key.
WARNING
Delete 0001WP
Are you sure?
YES NO
3. Push the [ENTER] knob.
The route is redrawn, eliminating the waypoint removed.
6. ROUTE
5-6
5.6 Information on Route Report
The route report provides various information about routes, such as time
distance and necessary fuel to go to a waypoint in route.
1. Open the route list.
2. Press the cursor pad (▲▼) to choose the route desired.
3. Rotate the [ENTER] knob to choose REPORT at the bottom of screen and
then push the [ENTER] knob.
The route report for the route appears.
SELECT NAME COLOR INVERT CLEAR SPEED FUEL
ROUTE REPORT
Route : 1 NAME: 0001RT
SPEED: 10.0 Kts FUEL: 10.0/h
WAYPOINT
LATITUDE
LONGITUDE
BRG
nm
LDST
nm
TDST
M
TIME
FUEL
0001WP
0002WP
0003WP
34 01.583N
124 53.634W
33 59.455N
124 57.228W
33 59.455N
124.48.527W
220
075
3.661
7.214
3.661
10.88
000:21
001:15
3.6
10.8
Waypoint name
Waypoint
position
Bearing
Leg distance
Total distance
Estimated navigation time
between previous and next waypoints
Estimated fuel consumption
(unit: liters) used for the
navigation between waypoints
Enter the speed to be
used for TIME calculation.
Enter your ship's estimated
fuel consumption per hour.
Route report
4. Press the [CLEAR] key twice to close the route report.
5. ROUTE
5-7
Entering the speed for TIME column
Enter speed to be used for TIME calculation.
1. Show the route report.
2. Rotate the [ENTER] knob to choose SPEED at the bottom of screen and
then push the [ENTER] knob to show the SPEED window.
SPEED
1 0.0 kt
You can change the digit by pressing the cursor pad (◄►).
3. Enter the ship’s speed and then SAVE soft key.
Entering the fuel consumption for FUEL column
Enter your ship’s estimated fuel consumption per hour to calculate fuel
consumption between two waypoints.
1. Show the route report.
2. Rotate the [ENTER] knob to choose FUEL at the bottom of screen and then
push the [ENTER] knob to show the FUEL window.
FUEL
0 10.0 kt
3. Enter the fuel consumption of your boat.
You can change the digit by pressing the cursor pad (◄►).
4. Press the SAVE soft key.
5.7 Changing the Color of Route Line
You can select the color for the route line among 8 colors: black, light-green, red,
purple, yellow, gray, brown and dark green.
1. Open the route list.
2. Press the cursor pad (▲▼) to choose a route.
3. Rotate the [ENTER] knob to choose COLOR at the bottom of screen and
then push the [ENTER] knob.
The color window appears.
4. Rotate the [ENTER] knob to choose a color.
5. Push the [ENTER] knob.
6. Press the [CLEAR] key to close the menu.
6. ROUTE
5-8
5.8 Searching Routes
You can search for a route through the route list or on the plotter display.
Searching a route through the route list
1. Open the route list.
2. Rotate the [ENTER] knob to choose SEARCH at the bottom of screen.
3. Push the [ENTER] knob.
The NAME window appears.
NAME
0001RT
Name window
4. Enter the route name you want to search.
You can change the digit by pressing the cursor pad (◄►).
5. Push the SAVE soft key.
The selected route name is shown at the top of the list.
6. Press the [CLEAR] key to close the menu.
Searching a route on the plotter display
1. Open the route list.
2. Press the cursor pad (▲▼) to choose the route desired.
3. Rotate the [ENTER] knob to choose PLOT at the bottom of screen.
4. Push the [ENTER] knob.
The plotter display appears with the chosen route at the screen center.
5.9 Reversing the Waypoints Order in a Route
The order of waypoints in a route can be reversed as follows.
1. Open the route list.
2. Press the cursor pad (▲▼) to choose the route desired.
3. Rotate the [ENTER] knob to choose REVERSE at the bottom of the screen.
4. Push the [ENTER] knob to reverse the waypoints order in the route.
5. Press the [CLEAR] key to close the list.
5.10 Erasing Routes
You can erase routes as follows:
1. Open the route list.
2. Press the cursor pad (▲▼) to choose the route you want to erase.
3. Rotate the [ENTER] knob to choose DELETE at the bottom of screen.
4. Press the [ENTER] knob twice to erase.
5. Press the [CLEAR] key to close the route list.
6-1
6. NAVIGATION
This chapter shows you how to get to a desired destination by using “quick
points”, waypoints, port services and routes.
6.1 Navigating to Quick Points
The quick points feature allows you to navigate to a cursor-selected location.
Each time a quick point is entered, the previous quick point is written over.
Navigating to a quick point
1. Operate the cursor pad to place the cursor at the location where you want to
enter a quick point.
2. Press the [TLL/GOTO] key to show the GO TO window.
CURSOR
POSITION
ROUTE
WAYPOINT
GO TO window
3. Rotate the [ENTER] knob to choose CURSOR and then push the [ENTER]
knob.
A line connects between own ship and destination, marked “DEST,” and it shows
the shortest course to the destination. The destination is marked with a flag.
Also, range and bearing from own ship to the destination appear in the data
window. This location is saved to the WAYPOINT LIST as waypoint “DEST.”
FIX DEST
34 35. 897N
135 16. 763E
DST
BRG
3.29nm
202 M
Quick point data window
You can also set the quick point by manually entering the longitude and latitude
of the point. Choose POSITION at step 3 to do this.
To cancel the navigation, locate the cursor on the quick waypoint and then press
the STOP soft key.
6. NAVIIGATION
6-2
Navigating a quick route
1. Press the cursor pad to place the cursor at the position where you want to
enter a waypoint.
2. Press the [ROUTE] key to show the new waypoint window.
3. If necessary, arrange the waypoint data.
4. Press the SAVE soft key.
5. Repeat steps 2 through 4 to complete the route.
Maximum 35 points can be entered. To erase a waypoint, place the cursor on the
waypoint which you want to erase and then press the DELETE soft key.
6. Press the cursor pad to place the cursor on the first quick point of the route.
7. Press the [TLL/GOTO] key.
A line connects between own ship and the all quick points. The line shows
the shortest course between quick points. Arrows on the line show the
direction to follow the route. Range and bearing from own ship to the first
destination appears in the data window.
To stop the navigation, place the cursor on the current destination and then
press the STOP soft key.
Note: You can continue to add the quick point up to 35 points. If you want to
create a new quick route, place the cursor on a leg in the route and then
press the RELEASE soft key.
6. NAVIGATION
6-3
Navigating to ports, port service
C-MAP NT+
TM
chart cards have a port service list which shows services
available at ports and harbors. You can use the list to set destination as follows.
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose FIND and then push the [ENTER] knob.
3. Rotate the [ENTER] knob to choose PORT SERVICES or PORT and then
push the [ENTER] knob to show the appropriate window.
Port service window Port window
4. Do one of the following depending on selection made at step 3.
PORT SERVICES
Select service mark desired with the [ENTER] knob, and then push the [ENTER]
knob. Then, the display shows the location of those services.
The appropriate port names are shown in order of distance from own ship.
Rotate the [ENTER] knob to choose the port desired and push the [ENTER]
knob twice. The service marks of the selected port appear. If you are okay to set
this port as destination, press the [ENTER] knob to close the window. Confirm
that the cursor is located on the selected port, and then press the [TLL/GOTO]
key. Choose CURSOR and then push the ENTER knob.
Sample filling station, service marks
PORT
Press the cursor pad (▲▼) to choose port and then press the [ENTER] knob.
Press the [ENTER] knob three times. Press the [TLL/GOTO] key, choose
CURSOR and then push the [ENTER] knob.
6. NAVIIGATION
6-4
6.2 Navigating to Waypoints
You can select an existing waypoint as destination by cursor, by name or
through the WAYPOINT LIST.
To cancel the navigation, locate the cursor on the destination waypoint, and then
press the STOP soft key.
Selecting waypoint by cursor
1. Press the cursor pad to place the cursor on the waypoint which you want to
set as destination.
2. Press the [TLL/GOTO] key.
A line runs between waypoint selected and own ship’s position. Also, range and
bearing from own ship’s position to waypoint appear in the data window.
Selecting waypoint by name
1. Press the cursor pad to place the cursor on a location not occupied by
waypoint.
2. Press the [TLL/GOTO] key to show the GOTO window.
CURSOR
POSITION
ROUTE
WAYPOINT
GOTO window
3. Rotate the [ENTER] knob to choose WAYPOINT and then push the [ENTER]
knob.
The SELECT NAME window appears.
0 0 0 1 WP
SELECT NAME
SELECT NAME window (for waypoints)
4. Enter the waypoint name you want to set as destination.
5. Press the SAVE soft key.
Selecting waypoint through WAYPOINT LIST
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose PLOTTER and then push the [ENTER]
knob.
3. Rotate the [ENTER] knob to choose WAYPOINTS and then push the
[ENTER] knob to show the WAYPOINT LIST.
4. Press the cursor pad (▲▼) to choose the waypoint which you want to set as
destination.
5. Press the [TLL/GOTO] key.
6. NAVIGATION
6-5
6.3 Following a Route
You can follow a route as follows.
Setting a complete route as destination
This method enables you to navigate from the first waypoint of a route.
1. Press the cursor pad to place the cursor at the location not occupied by
waypoint.
2. Press the [TLL/GOTO] key to show the GO TO window.
3. Rotate the [ENTER] knob to choose ROUTE and then push the [ENTER]
knob to show the SELECT ROUTE window.
1 0001RT
2 0002RT
3 0003RT
4 __________
5 __________
6 __________
7 __________
8 __________
9 __________
10 __________
SELECT ROUTE
ROUTE NAME
Select route window
4. Rotate the [ENTER] knob to choose a route which you want to set as
destination.
5. Push the [ENTER] knob.
Setting part of a route as destination
You can start the route navigation from any waypoint in a route.
1. Open the route list.
2. Press the cursor pad (▲▼) to choose the route desired.
3. Rotate the [ENTER] knob to choose PLOT at the bottom of the screen, and
then push the [ENTER] knob.
The plotter display appears.
4. Press the cursor pad to place the cursor on any waypoint which is part of the
route you want to set as destination.
5. Press the [TLL/GOTO] key.
A line runs between destination selected and own ship’s position. Also, range
and bearing from own ship’s position to destination appear in the data window.
You can change the destination in the route by pressing the PREV or NEXT soft
key.
6. NAVIIGATION
6-6
Skipping route waypoints
In some instances you may want to “skip” waypoints while following a route. In
the figure below, for example, the vessel has decided to navigate from waypoint
05 to 03, skipping waypoint 04.
PORT 1
PORT 2
Waypoint 1
Waypoint 2
Waypoint 3
Waypoint 4
Waypoint
5
Waypoint 6
New course line
1. Press the cursor pad to place the cursor on a waypoint which is part of the
route.
2. Press the ROUTE LIST soft key to show the route list.
3. Press the cursor pad to choose a route.
4. Rotate the [ENTER] knob to choose EDIT at the bottom of screen and then
push the [ENTER] knob.
The route menu appears.
5. Press the cursor pad (▲▼) to choose the waypoint you want to skip.
6. Press the SKIP soft key.
7. Press the SAVE soft key to close the route menu.
8. Press the [CLEAR] key to close the route list.
6.4 Canceling Navigation
1. Press the [TLL/GOTO] key.
The confirmation window appears.
WARNING
Destination is already present.
STOP START
2. Confirm that “STOP” is selected, and then push the [ENTER] knob.
The navigation is cancelled.
7-1
7. ALARMS
The plotter section has seven conditions which generate both audio and visual
alarms: arrival, XTE, temperature, depth, anchor, STW and grounding alarms.
When an alarm is violated both audio and visual alarms are released. You may
silence the audio alarm with the [CLEAR] key. The visual alarm remains on the
screen until the offending alarm is deactivated or the reason for the alarm has
disappeared.
You may set up the alarms on the ALARM menu.
1. Press the [MENU] key to show the menu bar.
Menu Bar
GENERAL PLOTTER MAP ALARMS ADVANCED INFO FIND
Menu bar
2. Rotate the [ENTER] knob to choose ALARMS and then push the [ENTER]
knob to show the ALARMS menu.
AUDIBLE ALARM Off
ARRIVAL ALARM Off
XTE ALARM Off
TEMPERATURE ALARM Off
DEPTH ALARM Off
ANCHOR ALARM Off
STW ALARM Off
GROUNDING ALARM Off
GROUNDING ALARM RANGE 0.25 nm
GROUNDING ALARM REPORT
FISH ALARM Off
FISH ALARM (B/L) Off
Alarms menu
7. ALARM
7-2
7.1 Audio Alarm On/Off
Audio and visual alarms are released whenever an alarm setting is violated. You
can enable or disable the audio alarm as follows:
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose ALARMS and then push the [ENTER]
knob to show the ALARMS menu.
3. Rotate the [ENTER] knob to choose AUDIO ALARM and then push the
[ENTER] knob.
Off
On
4. Rotate the [ENTER] knob to choose On or Off as appropriate.
5. Push the [ENTER] knob.
6. Press the [MENU] key to close the menu.
7.2 Arrival Alarm
The arrival alarm informs you that your boat is approaching a destination
waypoint. The area that defines an arrival zone is that of an imaginary circle
which you approach from the outside of it. The alarm will be released if your boat
enters the imaginary circle. Note that this alarm is available only when a
destination is set.
: Alarm area
Own ship
Alarm
range
Destination
waypoint
How the arrival alarm works
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose ARRIVAL ALARM and then push the
[ENTER] knob.
Off
0.00 nm
3. Rotate the [ENTER] knob to choose the “x.xx (value) nm” and then push the
[ENTER] knob.
4. Use the cursor pad to choose digit and rotate the [ENTER] knob to enter
value.
5. Press the SAVE soft key and [MENU] key in order to close the menu.
7. ALARMS
7-3
7.3 XTE (Cross-Track Error) Alarm
The XTE alarm warns you when your boat is off its intended course.
Note that this alarm is available only when a destination is set.
: Alarm
Destination
waypoint
Own ship
position
Alarm
setting
Intended
course
How to XTE alarm works
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose XTE ALARM and then push the
[ENTER] knob.
Off
0.00 nm
3. Rotate the [ENTER] knob to choose “x.xx (value) nm” and then push the
[ENTER] knob.
4. Rotate the [ENTER] knob to enter value.
To change the digit, press the cursor pad (◄►).
5. Press the SAVE soft key and [MENU] key in order to close the menu.
7. ALARM
7-4
7.4 Temperature Alarm
Note: This alarm requires water temperature data.
There are two types of water alarms: Within Range and Out of Range. The
Within Range alarm sounds when the water temperature is within the range set,
and the Out of Range sounds when the water temperature is higher or lower
than the range set.
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose TEMPERATURE ALARM and then push
the [ENTER] knob.
Off
Max +32.00 F
Min +32.00 F
3. Confirm that the cursor is at the top line, and then push the [ENTER] knob.
Off
Within Range
Out of Range
4. Rotate the [ENTER] knob to choose Within Range or Out of Range as
appropriate and then push the [ENTER] knob.
5. Rotate the [ENTER] knob to choose Max and then push the [ENTER] knob.
6. Enter the value for the maximum temperature and then press the SAVE soft
key.
7. Rotate the [ENTER] knob to choose Min, and then push the [ENTER] knob.
8. Enter the value for Min.
For Min, you can switch between plus and minus by rotating the [ENTER] knob.
9. Press the SAVE soft key and [MENU] key in order to close the menu.
7. ALARMS
7-5
7.5 Anchor Alarm
The anchor alarm informs you that your boat is moving when it should be at rest.
: Alarm
Own ship's
position
Setting range
How the anchor watch alarm works
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose ANCHOR ALARM and the push the
[ENTER] knob.
Off
0.00 nm
3. Rotate the [ENTER] knob to choose “x.xx (value) nm” and then push the
[ENTER] knob.
4. Rotate the [ENTER] knob to enter the value.
5. Push the [ENTER] knob and [MENU] key in order to close the menu.
7.6 STW Alarm
The STW alarm warns you when your boat’s speed is over the speed range set.
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose STW ALARMS and then push the
[ENTER] knob.
Off
Max +32.00 F
Min +32.00 F
3. Confirm that the cursor is located at the top line and then push the [ENTER]
knob.
4. Rotate the [ENTER] knob to choose On and then push the [ENTER] knob.
5. Rotate the [ENTER] knob to choose Max, and then push the [ENTER] knob.
6. Rotate the [ENTER] knob to enter the value, and then press the SAVE soft
key.
7. Rotate the [ENTER] knob to choose Min, and then push the [ENTER] knob.
8. Enter the value for Min, similar to how you did for Max.
9. Press the SAVE soft key and [MENU] key in order to close the menu.
7. ALARM
7-6
7.7 Depth Alarm
Note: This alarm requires depth data.
The depth alarm sounds when the depth is within the alarm range set.
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose DEPTH ALARM and then push the
[ENTER] knob.
Off
Depth 0000.0 Ft
Range 0010.0 Ft
3. Confirm that the cursor is located at the top line, and then push the [ENTER]
knob.
Off
On
4. Rotate the [ENTER] knob to choose On and then push the [ENTER] knob.
5. Rotate the [ENTER] knob to choose Depth and then push the [ENTER] knob.
6. Enter the starting point of range and then press the SAVE soft key.
7. Rotate the [ENTER] knob to choose Range and then push the [ENTER]
knob.
8. Enter the alarm range, deeper than Depth value, and then press the SAVE
soft key.
9. Press the [MENU] key to close the menu.
7. ALARMS
7-7
7.8 Grounding Alarm
The grounding alarm sounds when there is an object on chart data which is
within the depth range and depth set. Further, you can know what kind of object
is causing the alarm when it enters in the range.
1. Rotate the [ENTER] knob to choose ALARMS from the menu bar and then
push the [ENTER] knob to show the ALARMS menu.
2. Rotate the [ENTER] knob to choose GROUNDING ALARM and then push
the [ENTER] knob.
3. Rotate the [ENTER] knob to choose “xx (value) ft” and then push the
[ENTER] knob.
4. Enter the depth value desired.
5. Press the SAVE soft key [ENTER] knob in that order.
6. Rotate the [ENTER] knob to choose GROUNDING ALARM RANGE and then
push the [ENMTER] knob.
0.25 nm
0.5 nm
1.0 nm
7. Rotate the [ENTER] knob to choose the range and then push the [ENTER]
knob.
8. Push the [ENTER] knob and [MENU] key in order to close the menu.
When the grounding alarm warns, you can know what kind of object has entered
the setting range and depth by choosing GROUNDING ALARM REPORT from
the ALARMS menu.
7. ALARM
7-8
This page is intentionally left blank.
8-1
8. CUSTOMIZING YOUR UNIT
This chapter describes the various options which allow you to customize the
plotter section to suit your needs.
8.1 GENERAL Menu
The GENERAL menu provides the basic setup for the unit.
LANGUAGE English
KEYPAD BEEP Off
PALETTE Normal
TIME LINE Infinite
TIME REFERENCE UTC
TIME FORMAT 12 hour
DATE FORMAT MM-DD-YY
AUTO INFO On Points
SHIP ICON
WIND GRAPH
UNITS OF MEASURE
General menu
LANGUAGE
You can choose the language to display from among English, Italian, French,
German, Spanish, Norwegian and Swedish.
KEYPAD BEEP
Turns key beep on/off.
PALETTE
The display hue can be matched to the current lighting condition from among
Sun Light, Night, Normal and Classic.
TIME LINE
Choose the interval for the time line from among 2 min, 10 min, 30 min, 1 hour, 2
hours and Infinite. The length of the bar shows distance your ship will move
within selected time. Also the line can be erased by selecting Off.
TIME REFERENCE
GPS uses UTC time. If you would rather use local time, key in the time
difference between it and UTC time. Rotate the [ENTER] knob to change the
digits and “+” “-“.
TIME FORMAT
Chooses time notation; 12 hours or 24 hours.
8. CUSTOMIZING YOUR UNIT
8-2
DATE FORMAT
Chooses date notation; MM-DD-YY or DD-MM-YY.
AUTO INFO
Chooses what data is available with the cursor; Off, On Points or On All.
On Points: Data for selected chart symbol, for example, lighthouse or harbor.
All Points: Data for any location within the area covered by the chart.
SHIP ICON
Chooses the shape of own ship marker;
,or
+
.
WIND GRAPH
See section 2.10 for details about the wind display.
UNITS OF MEASURE
Chooses unit of measurement for distance, speed, depth, altitude and
temperature.
Distance: nm, sm, km, nm + ft, nm + m, sm + ft
(For “+ft” and “+m, ” it is used in the near range.)
Speed: Kt, mph, km/h
Depth: ft, fa, m, pb
Altitude: ft, fl, m
Temperature: ˚C, ˚F
8.2 MAP Menu
The MAP menu sets up the map display.
This menu can be shown by pressing the MAP soft key.
DISPLAY MODE Custom
CURRENT SETTING
CUSTOMIZE MAP
Map menu
DISPLAY MODE
Chooses the map to display; Full, Simple, Fishing, Low or Custom.
“Full” shows all data in the chart card. Note that CUSTOMIZE MAP (shown on
next page) can be arranged only when Custom is chosen here.
CURRENT SETTING
Shows the current map settings, which are set up with “CUSTOMIZE MAP” in
this menu.
8. CUSTOMIZING YOUR UNIT
8-3
CUSTOMIZE MAP
Chart objects may be turned on or off as desired. This setting is available when
selecting “Custom” at DISPLAY MODE.
MARINE SETTINGS
Item Settings
NAMES On, Off
NAV AIDS US, US smpl, INT, INT smpl, Off
LIGHT SECTORS On, Off
ATTENTION AREA On, Off
TIDES & CURRENTS On, Off
SEABED TYPE On, Off
PORTS & SERVICE On, Off
TRACKS & ROUTES On, Off
UNDERWATER OBJECTS On, Off
DEPTH SETTINGS
Item Settings
On, Off
DEPTH AREA
Enter ranges to display.
On, Off
DEPTH LINES & SOUNDINGS
Enter ranges to display.
LAND SETTINGS
Item Settings
RIVERS & LAKES On, Off
NATURAL FEATURE On, Off
CULTURAL FEATURES On, Off
LANDMARKS On, Off
CHART SETTINGS
Item Settings
LAT/LON GRID On, Off
CHART BOUNDARIES On, Off, Auto
CARTOGRAPHY On, Off
MIXING LEVELS On, Off
8. CUSTOMIZING YOUR UNIT
8-4
8.3 ADVANCED Menu
The ADVANCED menu calibrates data.
FIX
Item Settings
FIX CORRECTION
GPS-generated position may be off by
some seconds because of various
factors. In this case, you can
automatically correct GPS position by
selecting On.
COMPUTE CORRECTION
Corrects the GPS antenna position.
After placing the cursor at the own
ship’s true position, select this item.
CORRECTION OFFSET
Corrects the GPS antenna position
manually. Enter the longitude and
latitude numeric data of own ship’s true
position.
POSITION FILTER
When the DOP or receiving condition is
unfavorable, the GPS fix may change,
even if the vessel is dead in water. This
change can be reduced by smoothing
the raw GPS fixes. You can choose the
setting from among Off, Low, Medium
and High. The higher the setting, the
more smoothed the raw data, however
too high a setting slows response time
to change in latitude and longitude.
This is especially noticeable at high
ship’s speeds. Off is normal setting;
increase the setting if the GPS fix
changes.
SPEED FILTER
During position fixing, ship’s velocity
(speed) is directly measured by
receiving GPS satellite signals. The
raw velocity data may change
randomly depending on receiving
conditions and other factors. You can
reduce this random variation by
increasing the filter setting. Like with
latitude and longitude filter, the higher
the speed filter the more smoothed the
raw data. If the setting is too high,
however, the response to speed and
course change slows. For no
smoothing, choose Off. (Off, Low,
Medium, High)
8. CUSTOMIZING YOUR UNIT
8-5
NAVIGATE
Item Settings
COORDINATE SYSTEM
Choose the coordinate display method among
ddd mm ss, ddd mm.mm, ddd mm.mmm and
ddd.ddddd for latitude, or TD.
MAP DATUM
Geodetic datum is a reference for geodetic
survey measurements consisting of fixed
latitude, longitude and azimuth values
associated with a defined station of reference.
You must have the correct geodetic datum
selected in your plotter so that it will reference
the correct point on the chart for a given latitude
and longitude. Although WGS-84 is now the
world standard, other categories of charts still
exist.
MAP ORIENTATION North Up, Course Up, Auto Course Up
MAP ORIENTATION RES
Choose the resolution angle for the map
orientation. (Setting range: 5º to 60º)
COMPASS
Item Settings
BEARING
Choose how to calculate range and bearing, Mag or
True. True bearing is a bearing measured using true
North as the reference direction, and it is calculated by
the formula True Bearing = Magnetic Bearing -Magnetic
Variation. Magnetic bearings are measured with magnetic
north as the reference direction. Select Mag when using
a magnetic compass, True when using a gyrocompass.
VARIATION
The location of the magnetic north pole is different from
the geographical north pole. This causes a difference
between the true and magnetic north location. This
difference is called magnetic variation, and varies with
respect to the observation point on earth. Your unit is
preprogrammed with all the earth’s magnetic variations.
However, you may wish to enter variation manually to
refine accuracy by entering the magnetic variation
referring to a nautical chart.
CALIBRATION
Offsets latitude/longitude position to further refine
position accuracy. This table is used to match magnetic
value on the plotter with the readout of compass.
C-FORECAST
See the operation guidance for C-FORECAST (supplied with the optional kit)
8. CUSTOMIZING YOUR UNIT
8-6
8.4 INFO Menu
This menu shows the detailed information for the location selected by the cursor.
Choose a location, and then open the INFO menu and select item.
8.5 FIND Menu
You can find objects on the chart data in use dividing with the category of TIDE
STATION, WRECKS and OBSTRUCTIONS.
Choose the appropriate category from the FIND menu, and then push the
[ENTER] knob.
9-1
9. DATA TRANSFER
This chapter provides information for saving and replaying data to and from
memory cards, and updating and downloading data.
9.1 Memory Card Operations
The memory cards store these data: waypoints, routes and track.
9.1.1 Selecting the card slot to use
There are two card slots, upper and lower. Choose the one to use for memory
cards as follows:
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose PLOTTER and then push the [ENTER]
knob.
TRACK
ROUTES
WAYPOINTS
MEMORY CARD
Plotter menu
3. Rotate the [ENTER] knob to choose MEMORY CARD and then push the
[ENTER] knob.
The MEMORY CARD list appears.
NAME TYPE DATE TIME
SAVE LOAD DELETE INITIALIZE CHANGE
MEMORY CARD
SLOT
1
FILE
1
WPTS
7
QWPTS
0
RTES
2
TRKS
0
Currently
selected slot
Memory card list
4. Rotate the [ENTER] knob to choose CHANGE at the bottom of screen and
then push the [ENTER] knob to change the active slot.
The currently selected slot is shown at the left-hand top corner.
SLOT 1: Upper slot
SLOT 2: Lower slot
9. DATA TRANSFER
9-2
9.1.2 Formatting memory cards
Before you can use a memory card it must be formatted. This prepares the card
for use with the system. Note that formatting a memory card erases all data from
the card.
1. Insert the memory card to the selected slot.
2. Open the MEMORY CARD LIST.
3. Rotate the [ENTER] knob to choose INITIALIZE at the bottom of screen and
then push the [ENTER] knob.
WARNING
FORMAT USER CARTRIDGE
All data will be lost.
Are you sure?
YES NO
4. Push the [ENTER] knob to format the card.
Note: If the memory card was not inserted correctly, the message “FILE NOT
FOUND.” appears.
9.1.3 Saving data to a memory card
1. Insert a formatted memory card into the selected slot.
2. Press the [MENU] key to show the menu bar.
3. Rotate the [ENTER] knob to choose PLOTTER and then push the [ENTER]
knob to show the PLOTTER menu.
4. Rotate the [ENTER] knob to choose MEMORY CARD and then push the
[ENTER] knob to show the MEMORY CARD list.
5. Rotate the [ENTER] knob to choose SAVE and then push the [ENTER] knob.
SAVE FILE
NAME FILE01
TYPE WPTS
6. Enter the file name for which you want to save the data under.
7. Rotate the [ENTER] knob and then push the [ENTER] knob.
WPTS
TRACK
ROUTE
8. Rotate the [ENTER] knob to choose WPTS (waypoints), TRACK or ROUTE
as appropriate.
9. Push the [ENTER] knob.
10. Press the SAVE soft key.
9. DATA TRANSFER
9-3
9.1.4 Playing back data from a memory card
Data (track, waypoints, routes) can be loaded from a memory card and
displayed on the screen. This feature is useful for observing past data and
setting up the equipment for a specific purpose, with “setting data”.
1. Insert the memory card to play back into the selected slot.
2. Open the MEMORY CARD list.
3. Rotate the [ENTER] knob to choose LOAD and then push the [ENTER] knob.
9.2 Uploading/Downloading Data
You can upload/download waypoints and routes from/to a PC or another
GP-7000/F to the internal memory, through the NMEA1, NMEA 2 or RS-232C
port at the rear of the display unit.
9.2.1 Uploading/downloading waypoints data
You may upload/download all waypoints data as follows.
2. Connect the PC or another GP-7000/F to the equipment.
3. Choose INPUT/OUTPUT from the ADVANCED menu.
4. Choose NMEA 1 OUTPUT, NMEA 2 OUTPUT or RS232 3 OUTPUT
appropriately.
The sentence window appears.
GLL
VTG
BWR
DBT
DPT
MTW
VHW
WCV
APA
APB
HDG
BOD
XTE
RMA
RMB
RMC
GGA
HSC
AAM
GTD
MWV
ZDA
WPL
RTE
TLL Out
On
On
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
Off
On
On
Off
Off
Off
Off
Off
Off
On
On
On
Sentences window
5. Choose a sentence and then set it on or off.
6. Repeat step 5 to complete the sentences setting.
7. Press the [CLEAR] key several times to close the window and menus.
9. DATA TRANSFER
9-4
8. Open the WAYPOINT LISTS.
WAYPOINT LIST
SYM NAME TYPE
MODE
DST [nm}
BRG [M]
LATITUDE
LONGITUDE
ICON FIND LOCATE EDIT NEW
MODE DELETE SORT SEND RECEIVE
Waypoint list
9. Rotate the [ENTER] knob to choose SEND or RECEIVE at the bottom of the
screen.
SEND: Downloading all waypoints in the internal memory to external equipment.
RECEIVE: Uploading all waypoints to the internal memory from external
equipment.
10. Press the [ENTER] knob to execute.
When the boading is completed, the message “User Points sending (receiving
completed.” appears.
9. DATA TRANSFER
9-5
9.2.2 Uploading/downloading routes data
You may upload/download routes as follows.
Note: All waypoints in a route can be transported with the route.
1. Connect the PC or another GP-7000/F to the equipment.
2. Choose INPUT/OUTPUT from the ADVANCED menu.
3. Choose NMEA 1 OUTPUT, NMEA 2 OUTPUT or RS232 3 OUTPUT
appropriately.
The sentence window appears.
GLL
VTG
BWR
DBT
DPT
MTW
VHW
WCV
APA
APB
HDG
BOD
XTE
RMA
RMB
RMC
GGA
HSC
AAM
GTD
MWV
ZDA
WPL
RTE
TLL Out
On
On
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
Off
On
On
Off
Off
Off
Off
Off
Off
On
On
On
Sentences window
4. Choose a sentence and then set it on or off.
5. Repeat step 4 to complete the sentences setting.
6. Press the [CLEAR] key several times to close the window and menus.
7. Open the ROUTE LIST.
9. DATA TRANSFER
9-6
N NAME LENGTH
WAYPOINTS
FIND NEW EDIT RENAME COMMENT
PLOT DELETE REVERSE COLOR SEARCH
SEND RECEIVE CONNECT SELECT REPORT
ROUTE LIST
Route list
8. For downloading, press the cursor pad (▲▼) to choose the route desired.
9. Rotate the [ENTER] knob to choose SEND or RECEIVE at the bottom of the
screen.
SEND: Downloading the route chosen at step 8 to external equipment.
RECEIVE: Uploading all routes to the internal memory from external equipment.
10. Press the [ENTER] knob to execute.
When the loading is completed, the message “Route sending (receiving
completed.” appears.
10-1
10. VIDEO SOUNDER OPERATION
This chapter covers video sounder operation. The procedures in this chapter
assume that a full screen video sounder display is selected.
Principle of Operation
The video sounder determines the distance between its transducer and
underwater objects such as fish, lake bottom or seabed and displays the results
on screen. It does this by utilizing the fact that an ultrasonic wave transmitted
through water travels at a nearly constant speed of 4900 feet (1500 meters) per
second. When a sound wave is reflected back toward the source (transducer).
Thus by calculating the time difference between the transmission of a sound
wave and the reception of the reflected sound wave, the depth to the object can
be determined.
The entire process begins in the sounder. Transmitter power is sent to the
transducer as a short pulse of electrical energy. The electrical signal produced
by the transmitter is converted into an ultrasonic signal by the transducer and
transmitted into the water. Any returning signals from intervening objects (such
as a fish school) are received by the transducer and converted into an electrical
signal. The signals are then amplified in the amplifier section, and finally,
displayed on screen.
The picture displayed is made up of a series of vertical scan lines, one for each
transmission. Each line represents a snapshot of what has occurred beneath the
boat. A series of snapshots are accumulating side by side across the screen,
and the resulting contours of the bottom and fish between the bottom and
surface are displayed.
-
-
-
-
-
-
-
-
-
-
-
-
0
50
150
100
Underwater conditions and video sounder display
10. VIDEO SOUNDER OPERATION
10-2
10.1 Sounder Display
10.1.1 Description of sounder display
Color bar
Depth scale
Tx frequency
Depth
50
30
Temp
scale
Water
temp
graph
50.0
Minute marker
Bottom echo
Zero line
Fish
echo
40
0
50
100
150
Time
marker
0'30"
Time
200k
120
ft
Depth to VRM
VRM
Indications on the single frequency display
Single frequency
50 kHz picture
The sounder uses ultrasonic pulses to detect bottom conditions. The lower the
frequency of the pulse, the wider the detection area. Therefore, the low
frequency is useful for general detection and judging bottom condition.
200 kHz picture
The higher the frequency of the ultrasonic pulse the better the resolution.
Therefore, the high frequency is ideal for detailed observation of fish school.
50k frequency
200k frequency
Sounding area and transmission frequency
10. VIDEO SOUNDER OPERATION
10-3
1. Press the [DISP] key to show the DISPLAY MODE menu.
DISPLAY MODE
TURN KNOB TO SELECT DISPLAY MODE AND PRESS KNOB TO ENTER.
Display mode menu
2. Rotate the ENTER knob to choose the
icon.
3. Push the [ENTER] knob.
Selecting transmission frequency
The single frequency display shows either the 50k picture or 200k picture. To
select transmission frequency, do one of the following:
Using the soft key
Press the 50/200 kHz soft key to choose the frequency.
Through the menu
1. Press the [MENU] key to show the menu bar.
Menu Bar
GENERAL SOUNDER SENSITIVITY ALARMS RANGES
Menu bar
2. Rotate the [ENTER] knob to choose SOUNDER and then push the [ENTER]
knob to show the SOUNDER menu.
10. VIDEO SOUNDER OPERATION
10-4
AUTO MODE PRESET MANUAL
DISPLAY MODE NORMAL
FREQUENCY 50 KHz
PICTURE ADVANCE 1/1
TEMPERATURE GRAPH On
ZOOM MARKER On
A-SCOPE Off
SOUNDER SETUP
SENSOR SETUP
Sounder menu
3. Rotate the [ENTER] knob to choose FREQUENCY and then push the
[ENTER] knob.
50 kHz
200 kHz
4. Select 50 KHz or 200 KHz as appropriate and then push the [ENTER] knob.
5. Press the [MENU] key to close the menu.
10.1.2 Selecting a sounder display
There are seven display modes from which to choose: dual frequency, single
frequency, marker zoom, bottom zoom, bottom lock, bottom discrimination and
A-scope.
Dual frequency
The dual-frequency display provides both 50 kHz and 200 kHz pictures. This
display is useful for comparing the same picture with two different sounding
frequencies.
0.0
50k
200k
Dual-frequency display
To show the dual frequency display, do the following.
1. Press the [DISP] key.
2. Rotate the [ENTER] knob to choose
icon.
3. Push the [ENTER] knob.
10. VIDEO SOUNDER OPERATION
10-5
Bottom lock, Bottom zoom, Marker zoom, Bottom discrimination
Using the soft key
1. Press the DISP MODE soft key to show the display mode window.
NORMAL
BOTTOM LOCK
BOTTOM ZOOM
MARKER ZOOM
BOTTOM DISCRIMINATION
Display mode window
2. Rotate the [ENTER] knob to choose the mode desired and then push the
[ENTER] knob.
Through the menu
1. With a single frequency display selected, press the [MENU] key to show the
menu bar.
2. Rotate the [ENTER] knob to choose SOUNDER and then push the [ENTER]
knob.
AUTO MODE PRESET MANUAL
DISPLAY MODE NORMAL
FREQUENCY 50 KHz
PICTURE ADVANCE 1/1
TEMPERATURE GRAPH On
ZOOM MARKER On
A-SCOPE Off
SOUNDER SETUP
SENSOR SETUP
Sounder menu
3. Rotate the [ENTER] knob to choose DISPLAY MODE and then push the
[ENTER] knob.
NORMAL
BOTTOM LOCK
BOTTOM ZOOM
MARKER ZOOM
BOTTOM DISCRIMINATION
Display mode window
4. Rotate the [ENTER] knob to choose the mode desired and then push the
[ENTER] knob.
5. Press the [MENU] key to close the menu.
10. VIDEO SOUNDER OPERATION
10-6
Bottom-lock display
The bottom-lock display provides a compressed normal picture on the right half
of the screen and a 15 or 30 feet (5 or 10 meter) wide layer in contact with the
bottom is expanded onto the left half of the screen. This mode is useful for
discriminating bottom fish from the bottom echo.
Note: The range of the bottom-lock display can be changed at BOTTOM LOCK
RANGE on RANGES menu.
50k
88.7
0
Single frequency
display
Fish school
Bottom-lock
display
Zoom marker
This part is
zoomed.
50
0
10
20
30
Fish
school
ft
100
0.0
Bottom-lock display plus normal sounder display
Bottom-zoom display
The bottom-zoom display expands bottom and bottom fish echoes by the chosen
zoom range and is useful for determining bottom hardness. A bottom displayed
with a short echo tail usually means it is a soft, sandy bottom. A long echo tail
means a hard bottom.
Note: The range of the bottom-zoom can be changed at ZOOM RANGE on
RANGES menu.
50k
Single frequency display
Bottom-zoom display
Zoom marker
59.8
ft
Bottom
50
100
70
60
50
When depth changes,
the marker follows it automatically.
Bottom-zoom display plus normal sounder display
10. VIDEO SOUNDER OPERATION
10-7
Marker-zoom display
The marker-zoom display expands a selected area of the normal sounder picture
to full vertical size of the screen on the left-half window. You may specify the
portion to expand by operating the VRM (Variable Range Marker), which you can
shift with the [ENTER] knob. The area between the VRM and zoom marker is
expanded. The length of the segment is equal to one division of the depth scale.
Note 1: The VRM is set independently from other displays in case of multiple
displays.
Note 2: The range of the bottom-lock can be changed at BOTTOM LOCK
RANGE on RANGES menu.
0
50
100
50
40
30
20
12.8
VRM
This area is zoomed.
Single frequency display
Fish school
Zoom marker
Zoomed fish school
Marker
zoom display
25.0
50k
ft
Marker-zoom display plus normal sounder display
Bottom discrimination display
The bottom discrimination mode displays the bottom echo to help you determine
bottom hardness. A bottom displayed with a short echo tail usually means it is a
soft, sandy bottom. A long echo tail means a hard bottom.
Note: The range of the bottom discrimination can be changed at BOTTOM
LOCK RANGE on RANGES menu.
Long tail: Hard bottom
Short tail: Soft bottom
Seabed tail
50k
79.5
Single
frequency
display
ft
Bottom discrimination
display
0
50
100
50
0
10
This area
is zoomed.
Bottom discrimination display
10. VIDEO SOUNDER OPERATION
10-8
A-scope display (display only)
The A-SCOPE display, which can be enabled or disabled on the SOUNDER
menu, shows echoes at each transmission with amplitudes and tone proportional
to their intensities. It is useful for estimating fish specifies and seabed
composition.
50
100
0
59.6
ft
Strong echo
(bottom)
A-scope
Fish school
Ex. Single frequency display
50k
Weak echo
A-scope display
10.2 Automatic Sounder Operation
Automatic sounder operation is useful when you are preoccupied with other
tasks and do not have the time to adjust the display.
10.2.1 How the automatic sounder works
The automatic sounder function automatically selects the proper gain, range
scale and clutter suppression level according to the depth. It works as follows.
The range changes automatically to locate the bottom on the lower half of the
screen. The range jumps to one step shallower range when the bottom
echoes reach a half way point of the full scale from the top and to one step
deeper range when they come to the lower edge of the scale.
The gain is automatically adjusted to display the bottom echo in reddish brown
(default color arrangement).
Clutter, which suppresses low level noise, is automatically adjusted.
10. VIDEO SOUNDER OPERATION
10-9
10.2.2 Types of automatic sounder mode
Two types of automatic sounder modes are available: CRUISE and FISH.
CRUISE is for tracking the bottom, and FISH is for searching fish schools.
CRUISE uses a higher clutter rejection setting than FISH therefore it is not
recommended for fish detection – weak fish echoes may be erased by the clutter
suppression circuit.
10.2.3 How to enable automatic sounder operation
Using the soft key
1. Press the AUTO soft key to show the AUTO window.
MANUAL
FISH
CRUISE
Auto window
2. Rotate the [ENTER] knob to choose FISH or CRUISE as appropriate, and
then push the [ENTER] knob.
Through the menu
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose SOUNDER and then push the [ENTER]
knob to show the SOUNDER menu.
3. Rotate the [ENTER] knob to choose AUTO MODE PRESET and then push
the [ENTER] knob.
The AUTO MODE PRESET window appears.
MANUAL
FISH
CRUISE
AUTO MODE PRESET window
4. Rotate the [ENTER] knob to choose FISH or CRUISE as appropriate and
then push the [ENTER] knob.
5. Press the [MENU] key to close the menu.
10. VIDEO SOUNDER OPERATION
10-10
10.3 Manual Sounder Operation
Manual operation is useful for observing fish schools and bottom using a fixed
gain setting.
The gain, range and range shift functions used together give you the means to
select the depth you can see on the screen. The basic range can be thought of
as providing a “window” into the water column and range shifting as moving the
“window” to the desired depth.
10.3.1 Selecting the manual mode
Using the soft key
1. Press the AUTO soft key to show the AUTO window.
2. Rotate the [ENTER] knob to choose MANUAL and then push the [ENTER]
knob.
Through the menu
1. Open the SOUNDER menu.
2. Rotate the [ENTER] knob to choose AUTO MODE PRESET and then push
the [ENTER] knob.
3. Rotate the [ENTER] knob to choose MANUAL and then push the [ENTER]
knob.
4. Press the [MENU] key to close the menu.
10.3.2 Selecting display range
Press the [RANGE +] or [RANGE -] key to select a range. The default ranges in
feet are as below. Note that the range cannot be changed in the automatic
sounder mode.
Default sounder range
Range 1 Range 2 Range 3 Range 4 Range 5 Range 6 Range 7 Range 8
15 ft 30 ft 60 ft 120 ft 200 ft 400 ft 1000 ft 1500 ft
3 fa 5 fa 10 fa 20 fa 40 fa 80 fa 150 fa 300 fa
5 m 10 m 20 m 40 m 80 m 150 m 300 m 500 m
3 pb 5 pb 10 pb 30 pb 50 pb 100 pb 200 pb 300 pb
You can change the default settings on the RANGES menu. Choose a range
and use the [ENTER] knob to enter the desired range.
10. VIDEO SOUNDER OPERATION
10-11
10.3.3 Adjusting the gain
Normally, set the gain to the point where excessive noise does not appear on the
screen. Use a higher gain setting for greater depths and a lower setting for
shallower water.
Gain too high Gain proper Gain too low
Examples of proper and improper gain
1. Push the [ENTER] knob to show the SENSITIVITY window.
Note: This window can also be accessed with the SENSITIVITY menu.
GAIN 50* 000
NOISE LIMITER HIGH
CLUTTER 0
WHITE MARKER OFF
SIGNAL LEVEL OFF
*: For menu operation, both
of 50 and 200 frequencies appear.
Sensitivity window
2. For menu operation, choose GAIN 50 (kHz) or GAIN 200 (kHz) as
appropriate and then push the [ENTER] knob.
3. Rotate the [ENTER] knob to adjust. (Setting range: 0 to 100%)
4. Push the [ENTER] knob to set.
5. Press the [MENU] key to close the menu.
Note: Gain cannot be adjusted in the automatic sounder mode.
10. VIDEO SOUNDER OPERATION
10-12
10.4 Measuring Depth, Time
The VRM measures the depth and the time marker, time.
1. Rotate the [ENTER] knob to shift the VRM; counterclockwise to shift it
upward, clockwise to shift it downward. You may also use the cursor pad
(▲▼) to shift the VRM.
2. Press the cursor pad (◄►) to adjust the time marker to measure time.
VRM (white)
40.0
Depth to VRM
Time marker
50k
97
50
100
0
0'33"
Time for a scan line to travel
from the right edge of the
display to the cross-hair cursor
ft
How to measure depth and time
10. VIDEO SOUNDER OPERATION
10-13
10.5 Reducing Interference
Interference from other acoustic equipment operating nearby or other electronic
equipment on your boat may show itself on the display as shown below.
Interference from
other sounder
Electrical interference
Types of interference
To reduce interference, do the following:
1. Push the [ENTER] knob to show the SENSITIVITY window.
GAIN 50* 000
NOISE LIMITER HIGH
CLUTTER 0
WHITE MARKER OFF
SIGNAL LEVEL OFF
*: For menu operation, both
of 50 and 200 frequencies appear.
Sensitivity menu
2. Rotate the [ENTER] knob to choose NOISE LIMITER and then push the
[ENTER] knob to show the noise limiter window.
OFF
LOW
MEDIUM
HIGH
Noise limiter window
3. Rotate the [ENTER] knob to choose the degree of suppression desired (LOW,
MEDIUM, HIGH) or turn the noise limiter off.
4. Push the [ENTER] knob and [MENU] key in order to close the menu.
Turn the noise limiter circuit off when no interference exists, otherwise weak
echoes may be missed.
10. VIDEO SOUNDER OPERATION
10-14
10.6 Reducing Low Level Noise
Light-blue dots may appear over most of the screen. This is mainly due to
sediment in the water, or noise. This noise can be suppressed by adjusting
CLUTTER on the SENSITIVITY menu.
Appearance of clutter
When the automatic sounder mode is used, clutter is automatically adjusted. To
reduce low level noise in manual sounder operation, do the following:
1. Push the [ENTER] knob to show the SENSITIVITY window.
GAIN 50* 000
NOISE LIMITER HIGH
CLUTTER 0
WHITE MARKER OFF
SIGNAL LEVEL OFF
*: For menu operation, both
of 50 and 200 frequencies appear.
Sensitivity menu
2. Rotate the [ENTER] knob to choose CLUTTER and then push the [ENTER]
knob.
The CLUTTER setting is shown in reverse video.
3. Rotate the [ENTER] knob to choose the setting value. (Setting range: 0 to 7)
4. Push the [ENTER] knob and [MENU] key in order to close the menu.
Note: The setting range is 0-7; the higher the value, the greater the suppression
of low level noise. Choose “0” to turn clutter off.
10. VIDEO SOUNDER OPERATION
10-15
10.7 Erasing Weak Echoes
Sediments in the water or reflections from plankton may be painted on the
display in green or light-blue. These weak echoes may be erased as below.
Weak
echoes
Appearance of weak echoes
1. Push the [ENTER] knob to show the SENSITIVITY window.
GAIN 50* 000
NOISE LIMITER HIGH
CLUTTER 0
WHITE MARKER OFF
SIGNAL LEVEL OFF
*: For menu operation, both
of 50 and 200 frequencies appear.
Sensitivity menu
2. Rotate the [ENTER] knob to choose SIGNAL LEVEL and then push the
[ENTER] knob to show the signal level window.
OFF
SL1
SL2
SL3
SL4
OFF
SL1
SL2
SL3
SL4
SL5
SL6
SL7
SL8
SL9
PALETTE settings
on GENERAL menu: Classic
PALETTE settings
on GENERAL menu: other than Classic
Signal level window
3. Rotate the [ENTER] knob to choose level of erasure or OFF as appropriate.
The higher the number the stronger the echo that will be erased.
4. Push the [ENTER] knob and [MENU] key in order to close the menu.
Note: Unlike “clutter,” signal level reduces display colors. Therefore, if you do
not wish to reduce colors, use clutter instead.
10. VIDEO SOUNDER OPERATION
10-16
10.8 White Marker
The white marker functions to display a particular echo color in white. For
example, you may want to display the bottom echo in white to discriminate fish
echoes near the bottom.
1. Push the [ENTER] knob to show the SENSITIVITY window.
GAIN 50* 000
NOISE LIMITER HIGH
CLUTTER 0
WHITE MARKER OFF
SIGNAL LEVEL OFF
*: For menu operation, both
of 50 and 200 frequencies appear.
White marker window
2. Rotate the [ENTER] knob to choose WHITE MARKER and then push the
[ENTER] knob to show the white marker window.
OFF
01
White marker window
3. Rotate the [ENTER] knob to choose the color to display in white. (16:
strongest color, 0: weakest color)
As your rotate the knob, the number in the white marker window changes, the
white marker on the echo strength bar shifts and the chosen echo color is
displayed in white.
White marker shows
color currently
displayed in white.
Color bar when white marker function is active
4. Push the [ENTER] knob and [MENU] key in order to close the menu.
To turn the white marker function off, choose “OFF” from the white marker
window.
10. VIDEO SOUNDER OPERATION
10-17
10.9 Picture Advance Speed
The picture advance speed determines how quickly the vertical scan lines run
across the screen. When selecting a picture advance speed, keep in mind that a
fast advance speed will expand the size of the fish school horizontally on the
screen and a slow advance speed will contract it.
1. Open the SOUNDER menu.
AUTO MODE PRESET MANUAL
DISPLAY MODE NORMAL
FREQUENCY 50 KHz
PICTURE ADVANCE 1/1
TEMPERATURE GRAPH On
ZOOM MARKER On
A-SCOPE Off
SOUNDER SETUP
SENSOR SETUP
Sounder menu
2. Rotate the [ENTER] knob to choose PICTURE ADVANCE and then push the
[ENTER] knob to show the picture advance window.
STOP
1/16
1/8
1/4
1/2
1/1
2/1
Picture advance window
2. Rotate the [ENTER] knob to choose speed desired.
The fractions in the window denote the number of scan lines produced per
transmission. For example, 1/8 means one scan line is produced every eight
transmissions. STOP freezes the display and it is convenient for taking a picture
of the display.
3. Push the [ENTER] knob and [MENU] key in order to close the menu.
Note: When using a plotter/sounder combination display, advancement of the
sounder picture may be temporarily interrupted while the plotter display is
being shifted or its display range is being changed.
10. VIDEO SOUNDER OPERATION
10-18
10.10 Alarms
The sounder section has two conditions which generate audio and visual alarms:
fish (normal) and fish (bottom lock) alarms.
You may set up the sounder alarms on the ALARMS menu, which may be
displayed by choosing ALARMS from the menu bar.
AUDIBLE ALARM Off
ARRIVAL ALARM Off
XTE ALARM Off
TEMPERATURE ALARM Off
DEPTH ALARM Off
ANCHOR ALARM Off
STW ALARM Off
GROUNDING ALARM Off
GROUNDING ALARM RANGE 0.25 nm
GROUNDING ALARM REPORT
FISH ALARM Off
FISH ALARM (B/L) Off
Alarms menu
10.10.1 Audio alarm On/Off
Audio and visual alarms are released whenever an alarm setting is violated. You
can enable or disable the audio alarm as follows:
1. Press the [MENU] key to show the menu bar.
2. Rotate the [ENTER] knob to choose ALARMS and then push the [ENTER]
knob to show the ALARMS menu.
3. Rotate the [ENTER] knob to choose AUDIO ALARM and then push the
[ENTER] knob.
Off
On
4. Rotate the [ENTER] knob to choose On or Off as appropriate.
5. Push the [ENTER] knob.
6. Press the [MENU] key to close the menu.
10. VIDEO SOUNDER OPERATION
10-19
10.10.2 Fish alarm
The fish alarm sounds when a fish echo is within the preset alarm range. Note
that the sensitivity of the fish alarm can also be set.
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose FISH ALARM and then push the
[ENTER] knob twice.
Off
Depth 0000.0 Ft
Range 0010.0 Ft
Level Medium
Fish alarm window
3. Rotate the [ENTER] knob to select On or Off as appropriate. For On, enter
the depth, range and level (sensitivity).
For Level, choose High (red and stronger echoes trigger the alarm), Med (yellow
and stronger echoes trigger the alarm) or Low (blue and stronger echoes trigger
the alarm.)
4. Push the [ENTER] knob and [MENU] key in order to close the menu.
10.10.3 Fish alarm (B/L)
The bottom-lock fish alarm sounds when a fish echo is within a predetermined
distance from the bottom.
1. Open the ALARMS menu.
2. Rotate the [ENTER] knob to choose FISH ALARM (B/L) and then push the
[ENTER] knob twice.
Off
Depth 0000.0 Ft
Range 0030.0 Ft
Fish alarm (B/L) window
3. Rotate the [ENTER] knob to select On or Off as appropriate. For On, enter
the depth and range.
4. Push the [ENTER] knob and [MENU] key in order to close the menu.
10. VIDEO SOUNDER OPERATION
10-20
10.11 Water Temperature Graph
The water temperature graph (appropriate sensor required) plots water
temperature on the sounder display. It can be turned on or off as below.
1. Open the SOUNDER menu.
2. Rotate the [ENTER] knob to choose TEMPERATURE GRAPH and then push
the [ENTER] knob.
3. Rotate the [ENTER] knob to select On.
4. Push the [ENTER] knob and [MENU] key to close the menu.
10.12 Reviewing Past Picture
One past picture can be reviewed.
1. Open the SOUNDER menu.
2. Rotate the [ENTER] knob to choose SOUNDER SETUP and then push the
[ENTER] knob.
3. Rotate the [ENTER] knob to choose PLAYBACK SOUNDER IMAGE and
then push the [ENTER] knob.
Play
S-Down
Off
4. Rotate the [ENTER] knob to choose Play or S-Down.
Play: Rotate the [ENTER] knob counterclockwise to scroll the past picture.
S-Down: The entire past picture appears.
5. Push the [ENTER] knob and [MENU] key to close the menu.
6. Push the [ENTER] knob to show the SENSITIVITY window.
7. Rotate the [ENTER] knob to choose Play or S-Down appropriate.
8. Push the [ENTER] knob to start the Play (or S-Down) function.
9. To cancel, press the [CLEAR] key.
10. VIDEO SOUNDER OPERATION
10-21
10.13 Displaying Nav Data
You can show the navigation data at the left-hand side of the screen by pressing
the NAVDATA ON soft key.
Depth
50
30
50.0
200k
40
0
50
100
150
0'30"
34 40.209N
135 17.485E
COG 316 M
SOG 12.0 kt
TRIP 89 nm
DATE May/10/04
TIME 12:06 AM
TEMP 44.0 F
STW 11.4 kt
DPTH
ft
AUTO
MANUAL
120
Current mode
Own ship position (L/L)
Navigation
data
Sounder display, Nav data on
10. VIDEO SOUNDER OPERATION
10-22
10.14 SOUNDER SETUP Menu
The SOUNDER SETUP menu sets up the sounder section.
1. Press the [MENU] key to show the main menu.
2. Rotate the [ENTER] knob to choose SOUNDER and then push the [ENTER]
knob to show the SOUNDER menu.
3. Rotate the [ENTER] knob to choose SOUNDER SETUP and then push the
[ENTER] knob to show the SOUNDER SETUP menu.
TRANSMISSION Off
TRANSMISSION POWER Low
TRANSDUCER 600 W
50 KHz TVG 00
200 KHz TVG 00
50 kHz ECHO OFFSET +00
50 kHz BOTTOM LEVEL +000
200 kHz BOTTOM LEVEL +000
SMOOTHING SM2
DEPTH INFORMATION Large
PLAYBACK SOUNDER IMAGE Off
Sounder setup menu
TRANSMISSION
Turns TX power on/off.
Normally, “On” should be selected. To stop transmission, select “Off”. When
turning the power off and on again, “On” is selected automatically.
TRANSMISSION POWER
Sets transmission power to High or Low.
Normally, select “High”. When the gain becomes too high in shallow waters,
select “Low”.
TRANSDUCER
Selects the transducer to use, 600 W or 1 kW.
CAUTION
Select the transducer properly.
If not, the transducer may be damaged.
TVG (50 KHz, 200 kHz)
TVG (Time Varied Gain) compensates for propagation attenuation of the
ultrasonic waves. It does this by equalizing echo presentation so that fish
schools of the same size appear in the same density in both shallow and deep
waters. In addition, it reduces surface noise. Note that if the TVG level is set too
high short range echoes may not be displayed.
10. VIDEO SOUNDER OPERATION
10-23
ECHO OFFSET (50 kHz, 200 kHz)
If the on-screen echo level appears to be too weak or in manual operation too
strong and the level cannot be adjusted satisfactorily with the gain control on the
display unit, adjust echo offset to compensate for too weak or too strong echoes.
BOTTOM LEVEL (50 kHz, 200 kHz)
If the depth indication is unstable in automatic operation or the bottom echo
cannot be displayed in reddish-brown by adjusting the gain control in manual
operation, you may adjust the bottom echo level detection circuit, for both 50
kHz and 200 kHz, to stabilize the indication.
Note: If the BOTTOM LEVEL is set too low, weak echoes may be recognized as
the sea bottom, and the depth indication may be unstable. Reversely, if
the setting is too high, the depth indication will not be displayed.
SMOOTHING
Smoothes echoes to present stable display. The higher the setting the greater
the smoothing.
DEPTH INFORMATION
Selects the size of the depth indication, Large, Small or Off.
For the SENSOR SETUP menu, see the installation manual.
10. VIDEO SOUNDER OPERATION
10-24
10.15 Interpreting the Sounder Display
This section provides, using typical examples, information necessary for
interpreting the display.
LF
49.6
1/1
m
0.0
20
40
60
80
0
0
Surface
noise
Color bar
Bottom
Zero line
Fish school
Typical display
Color bar
The color bar shows the relation between echo intensity and echo color on the
screen. The top color (reddish brown) is the strongest color and the lower colors
the weakest. The bar can be used as a reference to estimate density of a fish
school, fish species and hardness of the bottom.
R-BRN
RED
ORANGE
YELLOW
GREEN
LIGHT-BLUE
BLUE
DEEP BLUE
Weak
Strong
No signal
49.6
m
Color bar
10. VIDEO SOUNDER OPERATION
10-25
Zero line
The zero line represents the transducers position. It moves off the screen when
a shifted range is used, or is shown at draft depth when ship’s draft is entered.
Zero line
Range shifted
Zero line
Bottom echoes
Bottom echoes are normally strongest and displayed in reddish brown or red, but
colors and width will vary with bottom material, depth, sea condition, installation,
frequency, pulselength and sensitivity.
Second bottom
echo
Color difference
in sea depth
Rugged bottom
Bottom material and bottom profile
Bottom profile
A hard and rough bottom appears with a longer tail because it reflects more of
the ultrasonic pulse. Because of their stronger return, shallow echoes appear
wider than deep ones even when all bottom conditions are equal. Also, a longer
bottom tail appears on slopes because of the difference in traveling time at both
edges of the beam angle. In the rugged bottom, echoes are reflected on many
different planes, overlapping to present a 3D effect.
Slope
Flat bottom
Bottom
with many
undulations
Bottom profile
10. VIDEO SOUNDER OPERATION
10-26
Bottom nature
The nature of the bottom is known from the intensity and length of the bottom tail.
Generally, when observing the bottom nature, the lower sounding frequency is
used, the pulselength is set to long, and the gain setting is not disturbed. In the
hard and craggy bottom, the bottom appears in reddish brown with a long tail. In
the muddy or sandy bottom, the bottom appears less reddish and with a short
tail. However, the bottom with sediment may give a long tail if a low frequency
sounding is used.
Rock base
Mud & sand
Bottom nature
Fish schools
Fish quantity
Fish quantity can be estimated to a certain extent from fish echoes on the screen
if fish school size and fish school density are kept in mind.
Fish school size
Usually the size of fish echoes on the screen is proportional to the actual size of
the fish school. However, if two fish echoes appear at different depths with the
same size, the fish school at shallower depth is smaller because the ultrasonic
beam widens as it propagates and a fish school in deep water is displayed
larger.
Size of
fish school
Small
school
Large
school
School depth
and sounding
time
Deep fish school sounding time
Shallow fish school sounding time
Fish school size
10. VIDEO SOUNDER OPERATION
10-27
Fish school density
If two schools appear with the same color at different depth, the one in deeper
water is denser because the ultrasonic wave attenuates as it propagates and the
fish school in deep water tends to be displayed in a weaker color.
Fish echo
Less Reddish
(Sparse echo)
Reddish
(Dense echo)
Difference in
signal strength
Weak Echo
Strong
Echo
Fish school density
Plankton
A plankton layer, a likely place to find fish, is displayed in green or blue dots. It
usually descends in the day and rises at night.
Fish
School
Plankton
Plankton
Current rip
When two ocean currents meet with different speeds, directions and water
temperatures, a current rip develops. A current rip’s on-screen appearance is as
shown below.
Current
rip
Current rip
10. VIDEO SOUNDER OPERATION
10-28
Surface noise
When the sea is rough or the ship passes over a wake, surface noise may
appear at the top of the screen.
Surface noise
Surface noise
Aerated water
When the sea is rough or the ship makes a quick turn, gaps in the bottom echo
on the screen may appear. This is caused by air bubbles which block
propagation of the sound wave. Generally low frequency ultrasonic waves are
interrupted more easily than high ones.
Ultrasonic wave
blocked by
aerated water
Aerated water
False echo
Every time ultrasonic pulse is transmitted, some radiation escapes on each side
of the beam, called “side lobes.” Echoes from side lobes show on the display as
false images as below.
False echo
Main
Lobe
Side
Lobe
11-1
11. MAINTENANCE &
TROUBLESHOOTING
11.1 Maintenance
Regular maintenance is important for continued performance. Important points to
be checked from time to time are shown below.
Do not open the equipment.
Hazardous voltage which can cause
electrical shock exists inside the
equipment. Only qualified personnel
should work inside the equipment.
WARNING
Location Check point Remedy
Antenna unit Check for loosened and
corroded bolts.
Tighten loosened bolts. Replace
heavily corroded bolts.
Check connection point for
watertightness.
Check connector for tightness
and corrosion.
Antenna cable
Check cables for damage.
Replace damaged parts.
Display unit connectors Check for tight connection. Tighten loosened connectors.
Ground terminal Check for tight connection and
corrosion.
Clean or replace as necessary.
Display unit Dust and foreign material on the
display unit.
Dust or dirt may be removed from
the cabinet with soft cloth.
Water-diluted mild detergent may
be used if desired. DO NOT use
chemical cleaners to clean the
display unit; they may remove paint
and markings.
Wipe the LCD carefully to prevent
scratching, using tissue paper and
an LCD cleaner. To remove dirt or
salt deposits, use an LCD cleaner,
wiping slowly with tissue paper so
as to dissolve the dirt or salt.
Change paper frequently so the
salt or dirt will not scratch the LCD.
Transducer Check the transducer face for
marine life, which can reduce
sensitivity.
Remove marine life from the
transducer when drydocking the
boat. Use a piece of wood to
remove any marine life.
11. MAINTENANCE & TROUBLESHOOTING
11-2
11.2 Replacement of Fuse
Use the correct fuse.
Use of a wrong fuse can cause fire or
damage the equipment.
CAUTION
The fuse on the power cable protects the system from reverse polarity of the
ship’s mains and equipment fault. If the fuse blows, find the cause before
replacing it. Use only a 3A fuse. Using the wrong fuse will damage the unit and
void the warranty.
Name Type Code No.
Fuse FGBO-A 3A AC125V 000-549-063
11.3 Replacement of Battery
A battery installed on the circuit board inside the display unit preserves data
when the power is turned off. The life of the battery is about three years. When
the battery voltage is low the battery icon (
) appears on the display. When this
happens, contact your dealer to request replacement of the battery.
Name Type Code No.
Battery CR2477/1HF 000-150-460-10
Note: If you require data currently displayed, save it to a SD memory card
before replacing the battery.
Be sure the battery is inserted correctly.
Wrong polarity may cause an explosion.
WARNING
11. MAINTENANCE & TROUBLESHOOTING
11-3
11.4 Simple Troubleshooting
This section provides simple troubleshooting procedures which the user can
follow to restore normal operation. If you cannot restore normal operation do not
attempt to check inside the unit. Any trouble should be referred to a qualified
technician.
General troubleshooting
If … Then …
check for blown fuse.
check that the power connector is firmly
fastened.
check for damaged power cable.
check battery for proper voltage output.
you cannot turn on the power
press the [POWER/BRILL] key a little harder.
no picture appears
press the [POWER/BRILL] key and then rotate
the [ENTER] knob.
there is no response when a
key is pressed
turn off and on the power.
the picture goes off suddenly*
press the [POWER/BRILL] key to turn the power
on.
*: When turning off and on again the breaker, press the [POWER/BRILL] key to
power on the equipment.
Plotter troubleshooting
If … Then …
check that antenna connector is firmly
fastened.
position is not fixed within 90 seconds
check number of satellites received, on
the GPS STATUS display.
position is wrong
enter position offset, on the
ADVANCED menu.
check that On is selected at TRACK in
the PLOTTER menu.
the track is not plotted
check that On is selected at VISIBLE in
the PLOTTER menu.
bearing is wrong check the VARIATION in the
ADVANCED menu.
the ship’s speed indication is not zero
after the ship is stopped
try to decrease SPEED FILTER in the
ADVANCED menu.
11. MAINTENANCE & TROUBLESHOOTING
11-4
Sounder troubleshooting
If … Then …
check if STOP is not selected at
PICTURE ADVANCE on the
SOUNDER menu.
check for loosened transducer
connector.
picture does not move although marks
and characters appear
on SOUNDER SETUP menu, set
TRANSMISSION POWER to High.
zero line does not appear through the
picture appears
the picture is shifted. Confirm shift
setting.
check gain setting, if using manual
operation.
marine life or air bubbles may be
clinging to transducer face.
picture sensitivity is too low
on SOUNDER SETUP menu, set
TRANSMISSION POWER to High.
the depth indication is not displayed
adjust gain and range to display the
bottom echo in reddish brown, if you
are using the manual operation.
if no noise appears after turning the
engine off, the engine interference is
suspected. Call your dealer.
check the ground.
noise or interference shows on the
display
other video sounder of the same
frequency as yours may be operating
near you.
temperature on the water on the water
temperature graph is wrong.
check that sensor cable is tightly
fastened.
11. MAINTENANCE & TROUBLESHOOTING
11-5
11.5 Diagnostics
This section provides the procedures for testing the equipment for proper
operation. Four tests are provided: RAM menu, Dim menu, Cartridges and Serial
ports. To access the test menu, do the following:
1. Press the [POWER/BRILL] key to turn on the equipment while holding the
[CLEAR] key down.
2. Release the [CLEAR] key when you hear the beep.
RAM menu
Dim menu
Cartridges
Serial ports
SYSTEM TEST
EC340 V0.00
NTSL V5.0.33R
SYSTEM TEST menu
11.5.1 RAM menu
The RAM menu checks each memory circuit and signal main board. Results for
device checks are shown as OK or NG (No Good). For any NG, request service.
1. Rotate the [ENTER] knob to choose “RAM menu” on the SYSTEM TEST.
2. Push the [ENTER] knob to show the RAM window.
RAM test
RAM clear
RAM window
3. Rotate the [ENTER] knob to select “RAM test” and then push the [ENTER]
knob to start the RAM test.
4. Confirm that “OK” appears.
11. MAINTENANCE & TROUBLESHOOTING
11-6
11.5.2 Dim menu
The Dim menu checks the contrast and backlight control circuits for proper
operation.
1. Rotate the [ENTER] knob to choose “Dim menu” on the SYSTEM TEST.
2. Push the [ENTER] knob to show the Dim window.
Contrast
Backlight
Dim window
3. Rotate the [ENTER] knob to select “Contrast” or “Backlight” as appropriate,
and then push the [ENTER] knob.
4. Press the cursor pad to change the setting.
5. Confirm that the contrast or backlight changes appropriately with adjustment
of the [ENTER] knob.
11.5.3 Cartridge
The Cartridge item checks internal chart data or the chart card data in use.
Checking the internal chart data
1. Rotate the [ENTER] knob to choose “Cartridge” on the SYSTEM TEST.
2. Push the [ENTER] knob to show the Cartridge window.
Internal Data Base Test
SD-CARD TEST
SD-CARD CONNECTOR
Cartridge window
3. Rotate the [ENTER] knob to choose “Internal Data Base Test” and then push
the [ENTER] knob to start the test.
4. Confirm the test result.
Checking the chart card in use
1. Rotate the [ENTER] knob to choose “SD-CARD TEST” on the Cartridge
window.
2. Push the [ENTER] knob to show the card test display.
3. Confirm the test result.
11. MAINTENANCE & TROUBLESHOOTING
11-7
11.5.4 Serial ports
You can confirm the signal input.
1. Rotate the [ENTER] knob to choose Serial port from the SYSTEM TEST.
2. Push the [ENTER] knob to show the Serial port window.
Change parameters
Input data display
Serial port
3. Rotate the [ENTER] knob to choose “Change parameters” and then push the
[ENTER] knob.
Port: PORT2
Baud Rate: 4800
Data Bits: 8
Parity: none
Stop Bits: 1
4. Enter the settings for the port in use and then push the [CLEAR] key.
5. Rotate the [ENTER] knob to choose “Input data display” and then push the
[ENTER] knob.
6. Press the [CLEAR] key twice to finish.
11. MAINTENANCE & TROUBLESHOOTING
11-8
11.6 Clearing the Memory
The memory can be cleared to restart operation with default settings. All tracks,
waypoints and routes are deleted and all default menu settings are restored.
1. Turn the power on while holding the [CLEAR] key down.
2. Release the [CLEAR] key when you hear the beep.
3. Rotate the [ENTER] knob to choose “RAM menu” and then push the
[ENTER] knob.
RAM test
RAM clear
RAM window
4. Rotate the [ENTER] knob to choose “RAM clear” and then push the [ENTER]
knob.
The message “Are you sure?” appears.
5. Push the [ENTER] knob to clean the memory.
The equipment restarts automatically.
11.7 GPS Cold Start
Cold start clears the Almanac (stored in the memory) to receive the latest
Almanac from the GPS satellites. When the equipment has not been used for a
long time (over one year), execute cold start as shown below to receive the
latest Almanac.
1. Choose ADVANCED from the menu bar, and then push the [ENTER] knob to
show the ADVANCED menu.
2. Rotate the [ENTER] knob to choose INPUT/OUTPUT, and then push the
[ENTER] knob.
3. Rotate the [ENTER] knob to choose INTERNAL GPS SETUP and then push
the [ENTER] knob.
RESTART GPS
INTERNAL GPS On
Internal GPS setup window
4. Rotate the [ENTER] knob to choose RESTART GPS.
5. Push the [ENTER] knob to restart.
A
P-1
APPENDIX
Menu Tree
Plotter
LANGUAGE (
English
, others)
KEYPAD BEEP (Off,
On
)
PALETTE (
Normal
, SunLight, Night, Classic)
TIME LINE (
Infinite
, off, 2 min, 10 min, 30 min, 1 hour, 2 hours)
TIME REFERENCE (
UTC
, -19:30 to +19:30 (in 30 min. steps))
TIME FORMAT (
12 hour
, 24 hour)
DATE FORMAT (
MM-DD-YY
, DD-MM-YY)
AUTO INFO (OFF,
On Points
, On All)
SHIP ICON (
,
+
,
)
WIND GRAPH (
True
, Apparent)
UNITS OF MEASUREMENT
GENERAL
DISTANCE (
nm
, sm, km, nm+Ft, NM+m, sm+ft)
SPEED (
km/h
, mph, Knh)
DEPTH (
Ft
, Fm, Mt, Pb)
ALTITUDE (
Ft
, FL, m)
TEMP ( C,
F
)
TRACK
ROUTE (Shows the route list.)
WAYPOINTS (Shows WAYPOINT LIST.)
MEMORY CARD (Shows MEMORY CARD list.)
PLOTTER
TRACKING (
Off
, On)
ACTIVE TRACK (
1
, 2, 3, 4, 5)
VISIBLE (
On
, Off)
LINE COLOR (
Black
, L-green, Red, Pink, Yellow, Gray, Brown, Dark-green)
Delete (
Yes
, No)
STEP UNIT (Time,
DIST
)
DISTANCE (0.01, 0.05,
0.1
, 0.5, 1.0, 2.0, 5.0, 10.0)
TIME (1 sec, 5 sec, 10 sec, 30 sec,
1 min
, 5 min, 10 min, 30 min, 1 h)
DISPLAY MODE (Full, Simple, Fishing, Low,
Custom
)
CURRENT SETTINGS (Shows the current map setting.)
CUSTOMIZE MAP
MAP
NAMES (
On
, Off)
NAV AIDS (
US
, US smpl, INT, INT smpl, Off)
LIGHT SECTOR (
On
, Off)
ATTENTION AREA (
On
, Off)
TIDE & CURRENT (
On
, Off)
SEABED TYPE (
On,
Off)
PORTS & SERVICES (
On
, Off)
TRACKS & ROUTES (
On
, Off)
UNDERWATER OBJECTS (
On
, Off)
MARINE SETTINGS
DEPTH SETTINGS
LAND SETTINGS
CHART SETTINGS
DEPTH AREAS (
On
, Off)
DEPTH AREAS > (
00005 Ft
)
DEPTH AREAS < (
00030 Ft
)
DEPTH LINES & SOUNDINGS (
On
, Off)
DEPTH LINES & SOUNDINGS > (
00000 Ft
)
DEPTH LINES & SOUNDINGS < (
01000 Ft
)
RIVERS & LAKES (
On
, Off)
NATURAL FEATURES (
On,
Off)
CULTURAL FEATURES (
On,
Off)
LANDMARKS (
On
, Off)
LAT/LON GRID (
On
, Off)
CHART BOUNDEARIES (
Auto, On,
Off)
CARTOGRAPHY (
On,
Off)
MIXING LEVELS (
On
, Off)
MENU BAR
1
APPENDIX
AP-2
AUDIO ALARM (
Off
, On)
ARRIVAL ALARM (
Off
, 0.00 to 5.39 nm)
XTE ALARM (Off, 0.00 to 5.39 nm)
TEMPERATURE ALARM (
Off
, MAX/MIN: -004.00 to +103.98 F)
DEPTH ALARM (
Off
, Depth/Range: 0 to 9999.9 ft)
ANCHOR ALARM (
Off
, 0.00 to 5.39 nm)
STW ALARM (
Off
, MAX/MIN: 000.0 to 539.9 kt)
GROUNDING ALARM (Off, 0 to 65
ft)
GROUNDING ALARM RANGE (
0.25 nm,
0.5 nm, 1.0 nm)
GROUNDING ALARM REPORT
FISH ALARM (
Off
, Depth/RANGE: 000.0 to 4000 ft, Level: High,
Medium
, Low)
FISH ALARM (B/L) (
Off
, Depth: 0 to 400, Range: 0 to 30.0 ft)
ALARMS
FIX
ADVANCED
FIX CORRECTION (
Off
, On)
COMPUTER CORRECTION
CORRECTION OFFSET
POSITION FILTER (
Off
, Low, Medium, High)
SPEED FILTER (
Off
, Low, Medium, High)
3
1
NAVIGATE
COORDINATE SYSTEM (
ddd mm.mmm
, ddd mm ss, ddd mm.mm, ddd. dddd, TD)
MAP DATUM (TIMBALAI 1948, TOKYO, TRISTAN 1968, VITI LEVU 16, VOIROL 1875,
VOIROL 1960, WAKE ISL.1952, WAKE-ENIWETOK, WGS 1972,
WGS 1984
)
MAP ORIENTATION (
North Up
, Course Up, Auto Course Up)
MAP ORIENTATION RES (05 to 60 ,
30
)
COMPASS
BEARING (
Mag
, True)
VARIATION (
Auto,
99.9 E to 99.9 W)
CALIBRTION
INPUT/OUTPUT
INTERNAL GPS SETUP (
RESTART GPS,
INTERNAL GPS (
On
, Off),
DIFF CORR SOURCE (Off,
WAAS
), WAAS SEARCH (
Auto
, Manual)
NMEA 1 OUTPUT (NMEA-0183 1200-N81-N,
NMEA-0183 4800-N81-N,
NMEA-0183 4800-N82-N, NMEA-0183 9600-N81-N, NMEA-0183 9600-O81-N,
C-COM, Disable)
NMEA 1 OUTPUT (
GLL, VTG
, BWR, DBT, DPT, MTW, VHW, WCV, APA,
APB
, HDG,
BOD, XTE, RMA,
RMB, RMC
, GGA, HSC, AAM, GTD, MWV,
WPL, RTE, TLL Out
)
NMEA 2 OUTPUT (NMEA-0183 1200-N81-N,
NMEA-0183 4800-N81-N,
NMEA-0183 4800-N82-N, NMEA-0183 9600-N81-N, NMEA-0183 9600-O81-N,
C-COM, Disable)
NMEA 2 OUTPUT (
GLL, VTG
, BWR, DBT, DPT, MTW, VHW, WCV, APA,
APB
, HDG,
BOD, XTE, RMA,
RMB, RMC
, GGA, HSC, AAM, GTD, MWV,
WPL, RTE, TLL Out
)
RS232/NMEA 3 OUTPUT (NMEA-0183 1200-N81-N,
NMEA-0183 4800-N81-N,
NMEA-0183 4800-N82-N, NMEA-0183 9600-N81-N, NMEA-0183 9600-O81-N,
C-COM, Disable)
RS232 3 OUTPUT (
GLL, VTG
, BWR, DBT, DPT, MTW, VHW, WCV, APA,
APB
, HDG,
BOD, XTE, RMA,
RMB, RMC
, GGA, HSC, AAM, GTD, MWV,
WPL, RTE, TLL Out
)
INPUT 3 MODE (
RS232
, NMEA)
DEPTH SOURCE (NMEA,
Sounder
)
TEMP SOURCE (NMEA,
Sounder
)
STW SOURCE (NMEA,
Sounder
)
EXT NMEA
DRAFT SETUP (-20.0 - +39.9 ft,
0.0
)
SPEED CALIBRATION (-50 - +50%,
0
)
TEMP CALIBRATION (-50 - +50 F,
0.0
)
C-FORECAST
C-FORECAST SETUP
DOWNLOAD PREVIEN
BROWSE
DISPLAY (
Off
, Wind, Waves)
WIND SPEED ALERT (
Off
, 000 to 250 km/h)
WAVES HEIGHT ALERT (
Off
, 00.0 to 25.0 m)
WIND SPEED UNIT (kt, m/s,
km/h
, Bft)
WAVE HEIGHT UNIT (ft,
m
)
USER IDTELEPHONE
NUMBER
SIM PIN
MAX SPEED (
00
to 40)
2
APPENDIX
A
P-3
GPS SIMULATION
ADVANCED
SIMULATION MODE (
Off
, On)
COURSE (
0
to 359 )
SPEED (0 to 539 kt,
1.0
)
DATE
TIME
CURSOR CONTROL (
Off
, On)
3
ECHO SOUNDER SIMULATION (
Off
, On)
SYSTEMJ UPDATE
PORT SERVICES
PORT
TIDE STATIONS
WRECKS
OBSTRUCTIONS
ROUTES
WAYPOINTS
COORDINATES (Longitude/Latitude)
INFO
FIND
APPENDIX
AP-4
Sounder
GENERAL (See page AP-1.)
AUTO MODE PRESET (
MANUAL
, FISH, CRUISE)
DISPLAY MODE (
NORMAL
, BOTTOM LOCK, BOTTOM ZOOM, MARKER ZOOM, BOTTOM DISCRIMINATION)
FREQUENCY (
50 kHz
, 200 kHz)
PICTURE ADVANCE (STOP, 1/16, 1/8, 1/4, 1/2,
1/1
. 2/1)
TEMPERATURE GRAPH (
Off
, On)
ZOOM MARKER (
Off
, On)
A-SCOPE (
Off
, On)
SOUNDER SETUP
SENSOR SETUP
SOUNDER
TRANSMISSION (
Off
, On)
TRANSMISSION POWER (
High,
Low)
TRANSDUCER (
600 W
, 1 kW)
50 kHz TVG (
00
to 10)
200 kHz TVG (
00
to 10)
50 kHz ECHO OFFSET (-50 to +50,
00
)
200 kHz ECHO OFFSET (-50 to +50,
00
)
50 kHz BOTTOM LEVEL (-100 to +100,
000
)
200 kHz BOTTOM LEVEL (-100 to +100, 000)
SMOOTING (
Off
, SM1, SM2, Sm3, SM4)
PLAYBACK SOUNDER IMAGE (
Off
, Play, S-Down)
GAIN 50 (0 to 100, 80)
GAIN 200 (0 to 100, 80)
NOISE LIMITER (
OFF
, LOW, MEDIUM, HIGH)
CLUTTER (0 to 16,
0
)
WHITE MARKER (
OFF
, 1 to 16)
SIGNAL LEVEL (Off, SL1 to SL9)*
SENSITIVITY
RANGE 1 (7 to 4000 ft,
15 ft
)
RANGE 2 (7 to 4000 ft,
30 ft
)
RANGE 3 (7 to 4000 ft,
60 ft
)
RANGE 4 (7 to 4000 ft,
120 ft
)
RANGE 5 (7 to 4000 ft,
200 ft
)
RANGE 6 (7 to 4000 ft,
400 ft
)
RANGE 7 (7 to 4000 ft,
1000 ft
)
RANGE 8 (7 to 4000 ft,
1500 ft
)
ZOOM RANGE (15 to 400 ft,
30 ft
)
BOTTOM LOCK RANGE (15,
30
ft)
RANGES
MENU BAR
DRAFT (-20.0 to 39.9 ft,
000.0
)
SPEED CALIBRATION (-50 to +50%,
00.0
)
TEMP CALIBRATION (-50 to 5 F,
0.0
)
ACOUSTIC SPED CALIBRATION (-50 to +50 m/s,
0
)
*: When PALETTE setting is Clasic: SL1 to SL4.
ALARMS (See page AP-2)
Range 1 Range 2 Range 3 Range 4 Range 5 Range 6 Range 7 Range 8 Setting range
3 fa 5 fa 10 fa 20 fa 40 fa 80 fa 150 fa 300 fa 666
5 m 10 m 20 m 40 m 80 m 150 m 300 m 500 m 1219
3 pb 5 pb 10 pb 30 pb 50 pb 100 pb 200 pb 300 pb 738
APPENDIX
A
P-5
What is WAAS?
WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based
Augmentation System) navigation system. An SBAS provider furnishes GPS signal corrections
to SBAS users. Two more SBAS providers are also currently under development, MSAS
(Multi-Functional Satellite Augmentation System) for Japan and EGNOS (Euro Geostationary
Navigation Overlay Service) for Europe. All providers will be compatible with one another, thus
providing “seamless” position fixes to SBAS users.
150
˚
W 120
˚
W 90
˚
W 60
˚
W 30
˚
W 0 30
˚
E 60
˚
E 90
˚
E 120
˚
E 150
˚
E
150
˚
W 120
˚
W 90
˚
W 60
˚
W 30
˚
W 0 30
˚
E 60
˚
E 90
˚
E 120
˚
E 150
˚
E
0
20
˚
S
40
˚
S
60
˚
S
20
˚
N
40
˚
N
60
˚
N
0
20
˚
S
40
˚
S
60
˚
S
20
˚
N
40
˚
N
60
˚
N
WAAS
EGNOS
MSAS
Satellite, Region Position
120, AOR-E
15.5˚W
122, AOR-W
54˚W
131, IOR
64.5˚E
134, POR
178˚E
131
134
122
120
Initial operation time
WAAS: 2003
EGNOS: 2004
MSAS: 2005
At the time of this software release, SBAS is still under development. (Providers are expected to
have initial operations capability from the times shown above.) During this developmental period,
which may last for several years, there is no guarantee of the accuracy, integrity, continuity, or
availability of the SBAS signal. Furuno will accept no responsibility for the use of the signal for
other than the above stated purpose. It is the users responsibility to exercise common
prudence and navigational judgment while using the SBAS signal in the developmental phase.
Note: This manual uses “WAAS” when referring to any SBAS provider.
APPENDIX
AP-6
World Time Chart
SP - 1
E4429S00A
SPECIFICATIONS OF GPS PLOTTER/SOUNDER
GP-7000F
1 GENERAL
1.1 Display 7-inch wide color TFT color LCD, 480 (W) x 234 (H) dots
1.2 Projection Mercator
1.3 Usable Area 80° latitude or below
1.4 Display Mode Plotter, Nav Data, Highway display, Compass display
1.5 Alarms Arrival and Anchor watch, Cross track error, Temperature,
Depth, Grounding, Ship’s speed alarms
2 GPS RECEIVER
2.1 Receiving Channels
GPS 12 channels parallel, 12 satellites tracking
WAAS 1 channel
2.2 Rx Frequency 1575.42 MHz
2.3 Rx Code C/A code, WAAS
2.4 Position Fixing System All in view, 8-state Kalman filter
2.5 Position Accuracy
GPS 10 m (95% of the time, HDOP 4)
WAAS 3 m (95% of the time)
2.6 Tracking Velocity 999 kt
2.7 Position-fixing Time Warm start: 12 s approx., Cold start: 90 s approx.
2.8 Position Update Interval 1 s
3 PLOTTER FUNCTIONS
3.1 Effective Projection Area Depending on chart card in use
3.2 Track Display Plot interval: by time
(1 sec, 5 sec, 10 sec, 30 sec, 1 min, 5 min, 10 min, 30 min, 1 h)
or by distance (0.01, 0.05, 0.1, 0.5, 1.0, 2.0, 5.0, 10.0 nm)
3.3 Memory Capacity Track: 12000 points, waypoint: 2000 points
Route: 200 routes with 35 waypoints each
3.4 MOB 1 point
3.5 Quick Routes 1 route
3.6 Electronic Chart Card C-MAP NT/NT+ chart SD card
SP - 2
E4429S00A
4 INTERFACE
4.1 Input data sentences IEC61162-1 and NMEA 0183 Ver1.5
DBT, DPT, MTW, TLL, WPL, VHW, HDT, HDG, DSC, MWV
4.2 Output data sentences IEC61162-1 or NMEA 0183 Ver1.5 selected on menu
$GPAAM, $GPAPB, $GPBOD, $GPBWC, $GPBWR, $GPGLL,
$GPGTD, $GPHDG, $GPGGA, $GPRMA, $GPRMB, $GPRMC,
$GPVTG, $GPXTE, $GPZDA, $GPWPL, $GPMWV, $GPVHW,
$GPTLL, $GPRTE, $GPMTW, $GPDBT/DPT
5 SOUNDER
5.1 Transmit Frequency 50 and 200 kHz, dual frequency
5.2 Transmission 600 Wrms or 1 kWrms
5.3 Display range 5/10/20/40/80/150/300/500 m, shift; 0-1200 m
15/30/60/120/200/400/1000/1500 ft, shift; 0-4000 ft
5.4 Extension Mode Marker zoom, Bottom zoom, Bottom rock, Bottom descrimination
5.5 Auto Mode Cruising/Fishing selected
5.6 Picture advance 6 steps
6 POWER SUPPLY
6.1 Display Unit 12-24 VDC: 1.5-0.8 A
7 ENVIRONMENTAL CONDITION
7.1 Ambient Temperature Antenna Unit: -20°C to +70°C
Display Unit: -15°C to +55°C
7.2 Relative Humidity 95% or less at 40°C
7.3 Water proofing Antenna Unit: IP46
(IEC60529) Display Unit: IP45
7.4 Vibration • 2 - 5 Hz and up to 13.2 Hz with an excursion of ±1 mm ±10%
(IEC 60945) (7 m/s² maximum acceleration at 13.2 Hz)
• 13.2 - 100 Hz with a constant maximum acceleration of 7 m/s²
8 COATING COLOR
8.1 Antenna Unit N9.5 (white)
8.2 Display Unit Cover: 2.5GY5/1.5, Panel: N3.0
IN-1
INDEX
A
alarms.............................................. 7-1, 10-18
anchor......................................................7-5
arrival.......................................................7-2
audio........................................................7-2
depth........................................................7-6
fish .......................................................10-19
fish (B/L) ..............................................10-19
grounding.................................................7-7
STW.........................................................7-5
temperature .............................................7-4
XTE..........................................................7-3
A-scope......................................................10-8
auto course-up.............................................2-2
auto info.......................................................8-2
automatic sounder.....................................10-8
B
battery........................................................11-2
bottom discrimination ................................10-7
bottom lock ................................................10-6
bottom zoom..............................................10-6
brilliance.......................................................1-4
C
cartridge.....................................................11-6
celestial display ...........................................2-9
chart card.....................................................1-2
chart scale ...................................................2-4
compass ......................................................8-5
compass display..........................................2-6
contrast........................................................1-4
course-up.....................................................2-2
CRUISE .....................................................10-9
cursor...........................................................2-3
current setting..............................................8-2
customize map ............................................8-3
D
date format ..................................................8-2
diagnostics.................................................11-5
Dim menu ..................................................11-6
display mode................................................8-2
download .....................................................9-3
dual frequency.......................................... 10-4
F
FISH.......................................................... 10-9
fix .................................................................8-4
fuse ............................................................11-2
G
gain ..........................................................10-11
GPS cold start............................................11-8
GPS status display ......................................2-8
graph display ............................................ 2-10
H
highway display ...........................................2-7
I
interference............................................. 10-13
K
keypad beep ................................................8-1
L
language......................................................8-1
M
maintenance..............................................11-1
manual sounder...................................... 10-10
marker zoom............................................. 10-7
memory card................................................9-1
menu............................................................1-7
MOB.............................................................1-6
N
nav data.................................................. 10-21
navigate .......................................................8-5
navigation ....................................................6-1
canceling..................................................6-6
route.........................................................6-5
IN-2
waypoints.................................................6-4
navigation data display................................2-5
North-up.......................................................2-1
P
palette..........................................................8-1
picture advance speed ............................10-17
port...............................................................6-3
port service..................................................6-3
Q
quick point ...................................................6-1
R
RAM menu.................................................11-5
route.............................................................5-1
connecting ...............................................5-3
color.........................................................5-7
erasing.....................................................5-8
report .......................................................5-6
reversing..................................................5-8
searching.................................................5-8
S
serial ports.................................................11-7
ship icon ......................................................8-2
simulation mode ..........................................1-9
single frequency ........................................10-2
soft keys.......................................................1-5
sounder display .........................................10-2
T
track.............................................................3-1
active .......................................................3-1
color.........................................................3-2
displaying.................................................3-2
erasing.....................................................3-4
hiding .......................................................3-3
interval .....................................................3-3
method.....................................................3-3
time format...................................................8-1
time line .......................................................8-1
time reference..............................................8-1
U
units of measure..........................................8-2
upload..........................................................9-3
W
WAAS .......................................................AP-5
water temperature graph.........................10-20
waypoint.......................................................4-1
editing ......................................................4-4
entering....................................................4-1
erasing.....................................................4-5
hiding .......................................................4-8
list.............................................................4-3
searching.................................................4-6
showing....................................................4-8
sorting......................................................4-6
wind display...............................................2-11
wind graph...................................................8-2
white marker............................................10-16
123

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno GP-7000F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno GP-7000F in de taal/talen: Engels als bijlage per email.

De handleiding is 1,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Furuno GP-7000F

Furuno GP-7000F Installatiehandleiding - English - 52 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info