522174
12
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
www.furuno.com
Installation Manual
RADAR SENSOR
DRS2D/DRS4D/
DRS4A/DRS6A/DRS12A/DRS25A
SAFETY INSTRUCTIONS ............................................................................i
SYSTEM CONFIGURATION ....................................................................... ii
EQUIPMENT LISTS....................................................................................iv
1. MOUNTING............................................................................................ 1
1.1 Mounting Considerations..............................................................................................1
1.2 Mounting Procedure for DRS2D/4D .............................................................................2
1.3 Mounting Procedure for DRS4A/6A/12A/25A...............................................................3
1.4 Mounting of Power Supply Unit ....................................................................................8
2. WIRING ................................................................................................ 11
2.1 Wiring inside DRS2D/4D ............................................................................................15
2.2 Wiring inside DRS4A/6A/12A/25A..............................................................................19
2.3 Wiring of Power Supply Unit.......................................................................................23
SPECIFICATIONS ................................................................................. SP-1
PACKING LISTS...................................................................................... A-1
OUTLINE DRAWINGS............................................................................. D-1
INTERCONNECTION DIAGRAMS.......................................................... S-1
i
WARNING
WARNING
Wear a safety belt and hard hat when
working on the antenna unit.
Serious injury or death can result if
someone falls from the radar mast.
Model
Distance to
100 W/m
2
point
Distance to
10 W/m
2
point
DRS4A
Nil
1.20 m
Nil
1.20 m
CAUTION
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
Only qualified personnel should work
inside the equipment.
Ground the equipment to prevent
electrical shock and mutual
interference.
Model
Standard
Steering
DRS4A
0.80 m
0.50 m
DRS6A
0.85 m
0.55 m
Radio Frequency Radiation Hazard
DRS6A
SAFETY INSTRUCTIONS
DRS12A
DRS2D
Nil
0.40 m
0.10 m
1.40 m
DRS4D
DRS4D
1.40 m
0.85 m
DRS2D
1.35 m
0.80 m
0.20 m
2.40 m
DRS12A (XN12A)
DRS12A (XN13A)
0.20 m
1.90 m
1.15 m
0.70 m
PSU-012
0.30 m
0.30 m
PSU-013
0.30 m
0.30 m
DRS25A
1.00 m
0.60 m
0.50 m
5.30 m
DRS25A (XN12A)
DRS25A (XN13A)
0.40 m
4.40 m
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Read these safety instructions before installing the equipment.
WARNING
Indicates a potentially hazardous situation which, if not avoided,
canresult in minor or moderate injury.
Warning, Caution
Prohibitive Action
CAUTION
Mandatory Action
The radar antenna emits electromagnetic radio
frequency (RF) energy which can be harmful,
particularly to your eyes. Never look directly into
the antenna aperture from a close distance while
the radar is in operation or expose yourself to the
transmitting antenna at a close distance.
Distances at which RF radiation levels of 100 and
10 W/m
2
exist are given in the table below.
Note: If the antenna unit is installed at a close
distance in front of the wheel house, your
administration may require halt of transmission
within a certain sector of antenna revolution. This
is possible - Ask your FURUNO representive or
dealer to provide this feature.
Construct a suitable service platform
from which to install the antenna
unit.
Serious injury or death can result if the
power is left on or is applied while the
equipment is being installed.
Turn off the power at the mains
switch board before beginning the
installation.
Fire, electrical shock or serious injury
can result if the power is left on or is
applied while the equipment is being
installed.
Observe the following compass safe distance
to prevent deviation of a magnetic compass.
PSU-017
0.30 m 0.30 m
ii
SYSTEM CONFIGURATION
DRS2D/4D/4A/6A/12A
RADAR SENSOR
DRS4A/DRS6A/DRS12A
RECTIFIER
RU-1746B
100/110/220/230 VAC12-24 VDC
NMEA 2000
Equipment
Multi Function Display BlackBox
MFDBB
*
1
:
The power supply unit (PSU-012/017) is necessary in the combination of radar sensor and multi function display.
NMEA 2000
Equipment
RADAR SENSOR
DRS2D/DRS4D
MFD8
MFD12
MFDBB
DRS2D/4D DRS4A DRS6A DRS12A
NO
NO
NO
NO
NO
NO
NO
PSU-012
NO
12-24 VDC
Multi Function Display
MFD8/12, TZT9/14
or
Multi Function Display BlackBox
TZTBB
Multi Function Display
MFD8/12, TZT9/14
or
Multi Function Display BlackBox
TZTBB
TZT9
TZT14
Power Supply Unit*
1
PSU-017*
2
Power Supply Unit*
1
PSU-017*
2
12-24 VDC
PSU-012
PSU-012
PSU-012
PSU-012
PSU-012
PSU-012
PSU-012
PSU-012
PSU-012
PSU-012 or PSU-017
PSU-012 or PSU-017
*
2
:
The disconnecting device (breaker, etc.) is required when the power cable of PSU-017 is connected to ship’s mains.
Power Supply Unit*
1
PSU-012
Power Supply Unit*
1
PSU-012
TZTBB
PSU-012 or PSU-017 PSU-012 PSU-012 PSU-012
or
iii
DRS25A
RADAR SENSOR
DRS25A
RECTIFIER
RU-1746B
100/110/220/230 VAC
12-24 VDC
NMEA 2000
Equipment
Power Supply Unit
PSU-013
12-24 VDC
Multi Function Display
MFD8/12, TZT9/14
or
Multi Function Display BlackBox
MFDBB, TZTBB
Multi Function Display
MFD8/12, TZT9/14
or
Multi Function Display BlackBox
MFDBB, TZTBB
iv
EQUIPMENT LISTS
Standard supply
Name Type Code No. Qty Remarks
Radar Sensor XN10A-RSB-118-092 - 1 For DRS4A, w/CP03-32601
XN12A-RSB-118-093 1 For DRS6A, w/CP03-32601
XN12A-RSB-118-094 - 1 For DRS12A, 1255 mm,
w/CP03-32601
XN13A-RSB-118-094 1 For DRS12A, 1795 mm,
w/CP03-32601
XN12A-RSB-118-095 - 1 For DRS25A, 1255 mm, w/CP03-
32601
XN13A-RSB-118-095 - 1 For DRS25A, 1795 mm, w/CP03-
32601
DRS2D - 1 Radome, 2 kW,
w/CP03-32101
DRS4D - 1 Radome, 4 kW,
w/CP03-32101
Power Supply
Unit
PSU-013 - 1 For DRS25A, w/SP03-16101 and
CP03-32700
Installation
Materials
CP03-32101 001-025-270 1 set For DRS2D/4D
CP03-32601 001-025-780 1 set For DRS4A/6A/12A/25A
CP03-32200 000-011-720 1 Two-way cable, MOD-ASW0001-
100+, 10 m, for DRS2D/4D/4A/6A/12A
CP03-32300 000-011-721 Two-way cable, MOD-ASW0001-
150+, 15 m, for DRS2D/4D/4A/6A/12A
CP03-32400 000-011-722 Two-way cable, MOD-ASW0001-
200+, 20 m, for DRS2D/4D/4A/6A/12A
CP03-32500 000-011-723 Two-way cable, MOD-ASW0001-
300+, 30 m, for DRS2D/4D/4A/6A/12A
CP03-32800 000-011-990 Two-way cable, MOD-ASW0002-
100+, 10 m, for DRS25A
CP03-32810 000-011-991 Two-way cable, MOD-ASW0002-
150+, 15 m, for DRS25A
CP03-32820 000-011-992 Two-way cable, MOD-ASW0002-
200+, 20 m, for DRS25A
CP03-32830 000-011-993 Two-way cable, MOD-ASW0002-
300+, 30 m, for DRS25A
v
Optional supply
*: After the wiring, it is required to wind the vinyl tape around the LAN connector to waterproof.
Name Type Code No. Remarks
Power Supply
Unit
PSU-012 -
PSU-017 - For DRS2D/4D
Gasket OP03-203 001-025-290
For DRS2D/4D, φ10 NMEA2000 cable
OP03-205 001-025-790
For DRS4A/6A, φ10 NMEA2000 cable
OP03-206 001-035-290
For DRS25A, φ10 NMEA2000 cable
Resister Assy OP03-204 001-025-300 For NMEA2000 connection with a unit
Radome
Mount
OP03-208 001-078-340 For DRS4D
OP03-209 001-078-350 For DRS2D
Joint Box* TL-CAT-012 000-167-140-10 For LAN cable extension
LAN Cable MOD-Z072-020+ 000-167-175-10 2 m
MOD-Z072-050+ 000-167-176-10 5 m
MOD-Z072-100+ 000-167-177-10 10 m
Cable Assy M12-05BFFM-010 000-167-965-10
NMEA2000, φ6, w/connector, 1 m
M12-05BFFM-020 000-167-966-10
NMEA2000, φ6, w/connector, 2 m
M12-05BFFM-060 000-167-967-10
NMEA2000, φ6, w/connector, 6 m
CB-05BFFM-010 000-167-971-10
NMEA2000, φ10, w/connector, 1 m
CB-05BFFM-020 000-167-972-10
NMEA2000, φ10, w/connector, 2 m
CB-05BFFM-060 000-167-973-10
NMEA2000, φ10, w/connector, 6 m
1
1. MOUNTING
1.1 Mounting Considerations
The radar sensor is generally installed either on top of the wheelhouse or on the radar mast on
a suitable platform. Locate the radar sensor where there is a good all-round view. Any obstruc-
tion will cause shadow and blind sectors. A mast for instance, with a diameter considerably less
than the horizontal beamwidth of the radiator, will cause only a small blind sector, but a horizon-
tal spreader or crosstrees in the same horizontal plane as the radar sensor would be a much
more serious obstruction; you would need to place the radar sensor well above or below it.
It is rarely possible to place the radar sensor where a completely clear view in all directions is
available. Thus, you should determine the angular width and relative bearing of any shadow
sectors for their influence on the radar at the first opportunity after fitting.
A magnetic compass will be affected if the radar sensor is placed too close to it. Observe the
compass safe distances mentioned in the SAFETY INSTRUCTIONS to prevent interference to
a magnetic compass.
Do not paint the radiator aperture and radome to ensure proper emision of the radar waves.
When this radar sensor is to be installed on large vessels, consider the following points:
The two-way cable run between the radar sensor and MFDBB, MFD8, MFD12 or PSU-012
comes in lengths of 10 m, 15 m, 20 m or 30 m.
Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial per-
formance and hot gases may distort the radiator portion. The radar sensor must not be
mounted where the temperature is more than 55 degrees centigrade.
As shown in the figure below, the radar sensor may be installed on a common mast or on the radar
mast.
For DRS4A/6A/12A/25A
NOTICE
Do not apply paint, anti-corrosive sealant or contact
spray to coating or plastic parts of the equipment.
Those items contain organic solvents that can damage coating and
plastic parts, especially plastic connectors.
(a) Common mast
(b) Radar mast
2
For DRS2D/4D
1.2 Mounting Procedure for DRS2D/4D
1. Remove mounting hardware at the bottom of the radar sensor, four each of hex bolts
(M10x20), spring washers and flat washers. Save the spring washers and flat washers to use
them to fix the radome base to the platform, at step 3. If the thickness of the mounting platform
is 5 mm or less, also save the bolts.
2. Construct a platform (steel or aluminum) 6-10 mm in thickness referring to the outline drawing
at the back of this manual. Fasten the platform to the mounting location. Next, position the
base so the cable entrance is facing the stern.
Note: When drilling holes in the platform, be sure they are parallel with the fore and aft line.
Radar sensor
Radar sensor
Radar sensor
Radar sensor
Screws
(two screws on other side)
Stern
Bow
Cable entry
Hex bolt (M10 x 20)
Spring washer
Flat washer
3
3. Use the hex bolts*, flat washers and spring washers removed at step 1, and fasten the
radome base to the platform. The torque should be between 19.6-24.5N
zm.
*If the thickness of the platform is 6-10 mm, use M10x25 bolts (supplied). For thicker platform, use
locally supplied bolts.
4. Mount the cover tentatively. The cover is opened for wiring at Chapter 2.
1.3 Mounting Procedure for DRS4A/6A/12A/25A
Refer to the outline drawing at the back of this manual, and drill five holes in the mounting platform:
four holes of 15 mm in diameter for fixing the radar sensor and one hole of 25-30 mm in diameter
for the signal cable. The outline drawing shows two cable entrance holes, one on the radar sensor
and one on the rubber mat. Use only the one on the rubber mat.
1.3.1 Fastening the radiator to the radiator bracket
1. Remove the radiator cap from the radiator bracket.
2. Coat the surface of the radiator bracket with silicone sealant as shown in the figure below.
3. Coat threaded holes on the antenna radiator with silicone sealant.
4. Grease the O-ring and set it to the radiator bracket.
Flat
washer
Antenna base
assy.
Spring
washer
Platform
Hex bolt
Apply silicone sealant.
(M10 x 25
or M10 x 20)
Transceiver
module
5 mm or under: M10x20 (local supply)
6-10 mm: M10x25 (supplied)
over 10 mm: locally supplied bolts
As for length, use the bolt
the "L" shown in the figure
in left becomes 10 to 15 mm.
L
RADIATOR BRACKET
(top view)
Coat hatched area with
silicone sealant.
10mm
(Do not coat.)
4
5. Coat the hex bolts (4 pcs.) with silicone sealant. Fasten the antenna radiator to the radiator
bracket with the hex bolts, flat washers and spring washers supplied with the radiator Then,
apply silicone sealant around the junction part between the radiator and bracket.
6. Apply silicone sealant to holes to prevent water ingress.
1.3.2 Mounting the radar sensor
The radar sensor can be mounted using the fixing holes on the outside (200 x 200 mm) or inside
(140 x 150 mm) the radar sensor.
Using outside fixing holes of radar sensor
Use the hex bolts (supplied) to mount the radar sensor as below.
1. Lay the corrosion-proof rubber mat (supplied) on the mounting platform.
Flat washer
Spring washer
Hex bolt
(M8 x 30)
Radiator bracket
Coat bolts with
silicone sealant.
Antenna
radiator
O-ring
Coat threaded
holes with
silicone sealant.
Radiator bracket, bottom view
(four): Holes
where to apply
silicone sealant.
Apply silicone sealant
around the joint part
with the antenna
radiator.
Rubber mat
Ground terminal
Bow mark
5
2. Lay the radar sensor on the mounting platform, orienting it as shown below. (The hinges must
face toward the stern.)
3. Insert four hex bolts (M12 x 60, supplied) and seal washers (φ30, supplied) from the top of the
housing, as shown below.
STERN
BOW
Hinge
CAUTION
Do not lift the radar sensor by the
radiator; lift it by the housing.
The radiator may be damaged.
Hex. bolt
Seal washer
(Face projecting part down.)
Flat washer
Spring washer
Nut
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno DRS12A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno DRS12A in de taal/talen: Engels als bijlage per email.

De handleiding is 23,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info